|
|
Data Connection Processing
Last updated: June 18, 2009
This page provides links to descriptions of the numerous settings and operations available in the test set for base station emulation and data connection processing including:
Data Connection Processing Overview
,
Access Network Emulator Configuration
,
Data Connection Processing Operations
,
Access Terminal Information
,
Test Set Operating Modes
and
General Information
.
If you have trouble finding the information you need below, use the "Search" functionality to search the contents of this guide. If you are new to using the test set, it may be helpful to review the
Getting Started with Data Connection Processing
section, which further describes where to find key data connection processing content.
Data Connection Processing Overview
Access Network Emulator Configuration
|
Parameters Under Call Control Menus
|
Parameters Under Call Parms Menus
|
|
Operating Mode
,
System Type
|
Cell Power
|
|
Handoff
Setup |
Cell Band
|
|
AT Max Power Parameter:
|
Channel
|
|
Session App Pre Configure
|
|
|
Access Network Info:
-
Configurable Attribute Parms:
Preferred Control Channel Cycle Control
,
Rate 1M8 Supported Control
(
only for subtype 2 physical layer
),
Enhanced Idle State Protocol Slotted Control
(Lab Application Only
)
-
Cell Parameters:
Sector ID
,
Country Code
,
Color Code
,
Subnet Mask
,
Control Channel Data Rate
,
Preferred Control Channel Cycle
,
Pilot Drop
-
Channel Gain/Traffic Info:
-
Traffic Parameters:
DRC Length
-
Channel Gain Parameters:
ACK Channel Gain
,
DRC Channel Gain
,
Data Offset 9k6|19k2|38k4|76k8|153k6
,
Data Offset Nom
,
Auxiliary Pilot Channel Gain
(
only for subtype 2 and subtype 3 physical layer
),
DSC Channel Gain
(
only for subtype 2 and subtype 3 physical layer
)
-
Power Parameters Info
(
only for subtype 2 and subtype 3 physical layer
) including:
T2P Transition Settings
,
Termination Target Settings
,
TxT2P Gain Settings
,
Power Parameters Screen
-
Enhanced Traffic Parameters
(
only for subtype 2 and subtype 3 physical layer
) including:
Auxiliary Pilot Channel Min Payload
,
DSC Length
,
Short Packet Enabled Threshold
(
only for subtype 2 physical layer
),
DRC Length
-
RRI Gain Parameters
(
only for subtype 2 and subtype 3 physical layer
)
-
Access Parameters (
for subtype 0 physical layer
) or Enhanced Parameters (
for subtype 2 and subtype 3 physical layer
):
-
CDMA System Time / Sync Info:
CDMA System Time Parameters
,
Multi-unit Synchronization
(applicable to the lab application and to a test application with the required feature license
)
|
Application Config:
|
|
Generator Info:
|
FTAP Rate
(
only for subtype 0 physical layer
)
F-Traffic Format
(
only for subtype 2 and subtype 3 physical layer
)
F-Traffic Config
(
only for subtype 2 and subtype 3 physical layer
)
|
|
Multi-carrier Multi-unit (MCMU)
(
only for subtype 3 physical layer
)
|
|
|
Data Channel
(Lab Application Only
)
|
RTAP Rate
(
only for subtype 0 physical layer
)
R-Data Pkt Size
(
only for subtype 2 and subtype 3 physical layer
)
|
|
Ping
(Lab Application Only
)
|
Reverse Closed Loop Power Control
|
|
Protocol Logging
(applicable to the lab application and to a test application with the required feature license
)
|
Power Control Step
|
|
Digital Bus Information
(
applicable to the lab application and to a test application with the required feature license with rear panel digital bus only
)
|
Call Drop Timer
|
|
Multi-Flow Packet Application Info: (
only for Lab Application and subtype 2 or subtype 3 physical layer
)
|
Call Limit Mode
|
|
Enh M-Flow Pkt Application Info (
only for Lab Application and subtype 2 or subtype 3 physical layer
)
|
|
|
Traffic Channel MAC Info: (
only for Lab Application and subtype 2 or subtype 3 physical layer
)
|
Protocol Rel
|
|
|
Protocol Subtype Config:
|
|
|
Session Close
|
|
|
Receiver Control
|
|
|
Tx Timing Advance
|
Data Connection Processing Operations
Access Terminal Information
|
|
top
of page