How Do I Change Call Parameters?
Last updated: July 23, 2008
General Procedure
-
Press the
CALL SETUP
key.
-
Select any
Call Parms
softkey (
F7
to
F12
) to select a parameter.
-
Change the parameter as needed using the knob and/or keypad.
-
Select
More
(
1 of 3
) under
Call Parms
for additional call parameters.
-
Depending upon the current setting of the physical layer subtype, the Call Parms menus are different.
To Configure the Test Set to FTAP/RTAP Protocols
When the test set is configured to subtype 0 physical layer, the following parameters can be configured from the Application Configuration Window by selecting the
Application Config
(
F10
on
Call Parms 1 of 3
).
Application Configuration (for Subtype 0 Physical Layer)
-
To establish an FTAP connection for AT's receiver test in subtype 0 physical layer, you should set
Test Application Protocol
to
FTAP
. Change other parameters as needed for your tests.
-
To establish an RTAP connection for AT's transmitter test in subtype 0 physical layer, you should set
Test Application Protocol
to
RTAP
. Change other parameters as needed for your tests.
-
(
Lap Application Only
) To establish a DPA connection for data application test, you should set
Session Application Type
to
Default Packet Application
. (See
Session Application Type
).
Your settings are displayed in the
Application Configuration
window on the
Call Setup
screen. Also, the application (
FTAP
,
RTAP
or
DPkt
) and physical layer subtype (
PLSub0
) currently configured in the test set are displayed at the bottom of the screen.
To Configure the Test Set to FETAP/RETAP Protocols
When the test set is configured to subtype 2 physical layer, the following parameters can be configured from the Application Configuration Window by selecting the
Application Config
(
F10
on
Call Parms 1 of 3
).
Application Configuration (for Subtype 2 Physical Layer)
-
To establish an FETAP connection for AT's receiver test in subtype 2 physical layer, you should set
Enhanced Test Application Protocol
to
FETAP
. Change other parameters as needed for your tests.
-
To establish an RETAP connection for AT's transmitter test in subtype 2 physical layer, you should set
Enhanced Test Application Protocol
to
RETAP
. Change other parameters as needed for your tests.
-
(
Lap Application Only
) The test set currently does not support DPA test in subtype 2 physical layer.
Your settings are displayed in the
Application Configuration
window on the
Call Setup
screen. Also, the application (
FETAP
or
RETAP
) and physical layer subtype (
PLSub0
or
PLSub2
) being configured in the test set are displayed at the bottom of the screen.
To Configure the Test Set to FMCTAP/RMCTAP Protocols
When the test set is configured to subtype 3 physical layer, the following parameters can be configured from the Application Configuration Window by selecting the
Application Config
(
F10
on
Call Parms 1 of 3
).
Application Configuration (for Subtype 3 Physical Layer)
-
To establish an FMCTAP connection for AT's receiver test in subtype 3 physical layer, you should set
Multicarrier Test Application Protocol
to
FMCTAP
. Change other parameters as needed for your tests.
-
To establish an RMCTAP connection for AT's transmitter test in subtype 3 physical layer, you should set
Multicarrier Test Application Protocol
to
RMCTAP
. Change other parameters as needed for your tests.
Your settings are displayed in the
Application Configuration
window on the
Call Setup
screen. Also, the application (
FMCTAP
or
RMCTAP
) and physical layer subtype (
PLSub3
) being configured in the test set are displayed at the bottom of the screen.
To Configure the Test Set to Subtype 0 Physical Layer
To configure the test set to subtype 0 physical layer,
-
set the
Protocol Rel
(
F11
on Call Parms 2 of 3) to
0 (1xEV-DO)
, or
-
set the
Protocol Rel
(
F11
on Call Parms 2 of 3) to
A (1xEV-DO-A)
and set the
Release A Physical Layer Subtype
to
Subtype 0
from the
Protocol Subtype Configuration
menu by pressing the
F12
(
Protocol Subtype Config
).
To Configure the Test Set to Subtype 2 Physical Layer
To configure the test set to subtype 2 physical layer, set the
Protocol Rel
(
F11
on Call Parms 2 of 3) to
A (1xEV-DO-A)
and set the
Release A Physical Layer Subtype
(
F12
on Call Parms 2 of 3) to
Subtype 2
from the
Protocol Subtype Configuration
menu by pressing the
F12
(
Protocol Subtype Config
).
To Configure the Test Set to Subtype 3 Physical Layer
To configure the test set to subtype 3 physical layer, set the
Protocol Rel
(
F11
on Call Parms 2 of 3) to
B (1xEV-DO-B)
and set the
Release B Physical Layer Subtype
(
F12
on Call Parms 2 of 3) to
Subtype 3
from the
Protocol Subtype Configuration
menu by pressing the
F12
(
Protocol Subtype Config
).
Related Topics
How Do I Open a Session and Test Data Connection?
Cell Power
Cell Band
Channel
Application Config:
Session Application Type
(
Lab Application Only
),
Test Application Protocol
,
Limited TAP
,
AT Directed Packets
,
DRC Value Fixed Mode Attribute
,
ACK Channel Bit Fixed Mode Attribute
,
Enhanced Test Application Protocol
,
ACK Channel Modulation Type
,
Reverse Data Transmission Mode
,
Enhanced Access Rate
FTAP Rate
RTAP Rate
F-Traffic Format
F-Traffic Config
R-Data Pkt Size
Reverse Closed Loop Power Control
Power Control Step
Call Limit Mode
Call Drop Timer
Protocol Rel
Protocol subtype config:
Release A Physical Layer Subtype
,
Access Channel MAC Subtype
Session Close
Tx Timing Advance
Rcvr Power Ctrl (
Manual Operation: Manual Receiver Control
)
Meas Frequency (
Manual Operation: Manual Receiver Control
)
top
of page