Test Adherence to Standards

Last updated: October 16, 2009

Standards Table

Unless otherwise indicated, the capabilities shown in the tables apply to both the E1966A and the E6706A applications.

Support of C.S0033 Tests
C.S0033-A Test	Supported by Test Set?	Comments
3. Receiver Tests
3.1 Frequency Coverage Requirements	Yes	Supports Band Classes 0, 1, 3, 4, 5, 6, 10 and 14. See Cell Band .
3.2.1 Demodulation of Forward Traffic Channel in AWGN	Yes	See Testing 3.2.1 Demodulation of Forward Traffic Channel in AWGN .
3.2.2 Demodulation of Forward Traffic Channel in Multipath Fading Channel	Yes. ( Lab Application Only )	Requires external fader and AWGN generator. For example, the E5515C Fading Solution, see Digital Bus Information for reference information. ( Lab Application Only ) See also Testing 3.2.2 Demodulation of Forward Traffic Channel in Multipath Fading Channel (Lab Application Only) .
3.2.3 Decision of Power Control Bit for Channels Belonging to Different Power Control Sets During Soft Handoff	No	Requires soft handoff capability.
3.2.4 Decision of Power Control Bit for Channels Belonging to the Same Power Control Set	No	Requires soft handoff capability.
3.2.5 Demodulation of Reverse Power Control Channel During Soft Handoff	No	Requires soft handoff capability.
3.2.6 Demodulation of ARQ Channel	Yes	See Testing 3.2.6 Demodulation of ARQ Channel
3.2.7 Demodulation of Broadcast Channel	No
3.3.1 Receiver Sensitivity and Dynamic Range	Yes	See Testing 3.3.1 Receiver Sensitivity and Dynamic Range .
3.3.2 Single Tone Desensitization	Partially	Requires external CW signal generator.
3.3.3 Intermodulation Spurious Response Attenuation	Partially	Requires two external CW signal generators.
3.3.4 Adjacent Channel Selectivity	Partially	Requires external HRPD (1xEV-DO) and CDMA sources.
3.3.5 Receiver Blocking Characteristics	Partially	Requires external CW signal generator.
3.4.1 Conducted Spurious Emissions	No	Requires full spectrum analyzer
3.4.2 Radiated Spurious Emissions	No	Requires full spectrum analyzer

4. Transmitter Tests
4.1.1 Frequency Coverage	Yes	Supports Band Classes 0, 1, 3, 4, 5, 6, 10 and 14. See Cell Band .
4.1.2 Frequency Accuracy	Yes	See Testing 4.2.2 Waveform Quality and Frequency Accuracy .
4.2.1 Time Reference	Partially	Supports static time reference only. See Testing 4.2.2 Waveform Quality and Frequency Accuracy .
4.2.2 Waveform Quality and Frequency Accuracy	Yes	See Testing 4.2.2 Waveform Quality and Frequency Accuracy .
4.3.1 Range of Open Loop Output Power	Partially	Supports 100% forward packet activity only (see Fixed Settings ). See Testing 4.3.1 Range of Open Loop Output Power . If you want to view the access probe sequence graphically, use Measuring Graphical Access Probe Power ( Lab Application Only ).
4.3.2 Time Response of Open Loop Power Control	Yes	See Testing 4.3.2 Time Response of Open Loop Power Control
4.3.3 Range of Closed Loop Power Control	Partially	Supports tests 1 and 3-11, Minimum Standard (a) only, by remote program only.
4.3.4 Maximum RF Output Power	Yes	See Testing 4.3.4 Maximum RF Output Power
4.3.5 Minimum Controlled Output Power	Yes	See Testing 4.3.5 Minimum Controlled Output Power
4.3.6 Standby Output Power	Partially	Supports idle standby output power fully. Supports measurement of standby power between access probe bursts by remote program only.
4.3.7 RRI Channel Output Power	Yes	See Testing 4.3.7 RRI Channel Output Power
4.3.8.1 DRC Channel Output Power	Yes	See Testing 4.3.8 Code Domain Power
4.3.8.2 ACK Channel Output Power	Yes	See Testing 4.3.8 Code Domain Power
4.3.8.3 Data Channel Output Power	Partially	Supports tests 1-5, 8-10. See Testing 4.3.8 Code Domain Power
4.3.8.4 DSC Channel Output Power	Yes	This test is only used for subtype 2 physical layer testing. See Testing 4.3.8 Code Domain Power
4.4.1 Conducted Spurious Emissions	Yes	Supports adjacent and alternate channels only. Testing 4.4.1 Conducted Spurious Emissions
4.4.2 Radiated Spurious Emissions	Partially	Requires external spectrum analyzer.
4.4.3 Occupied Bandwidth	Partially	Requires external spectrum analyzer.
5 MAC Layer Minimum Standards
5.2 Data Rate Control Performance	Yes	Supports tests 1-5. See Testing 5.2 Data Rate Control Performance

Test Adherence to Standards

Standards Table

Related Topics