Agilent Technologies Home Page 8960 Series 10 Wireless Communications Test Set
- +
Home | Product Web Site | Contact Us
+
- -
+ -
8960 cdma2000 Online User's Guide
E1962B, E6702B
Search this guide for     
search tips


Feedback
Did the information on this web page help answer your question or solve a problem?

Yes
No
Did not apply

Please provide additional comments about this page.
(Optional, 255 character max)


Email address (optional):

Privacy Notice: We will not sell or give away your email address to any third party.

 

Terminologies on the Test Set Adherence to Standard

Last updated: October 28, 2004

This table lists the parameters required to be set in most standard tests. It is to help you quickly find the menus/softkeys on the test set's front panel to configure the parameters as specified in the standard.

Test Parameters
Parameters in Standard

Equivalent Settings on the Test Set
Ioc (dBm/1.23 MHz)

AWGN Power (see How Do I Change AWGN Power Levels? )
Î or (dBm/1.23 MHz)

Cell Power ( F7 on the Call Parms 1 of 3 ) (see How Do I Change Call Parameters? )
Ior/Ioc (dB)

Ior/Ioc is the ratio of Cell Power to AWGN. See Configuring Cell Power and AWGN Power Levels .
It is not directly settable. Normally, the Ioc has been specified. You need to set Cell Power to the value of (Ioc + Ior/Ioc) to achieve this setting.

Pilot Ec/Ior (dB)
Sync Ec/Ior (dB)
Paging Ec/Ior (dB)
QPCH Ec/Ior (dB)
BCCH Ec/Ior (dB)
FCCCH Ec/Ior (dB)
FCH Ec/Ior (dB)
SCH Ec/Ior (dB)

Cell F-Pilot Level
Cell F-Sync Level
Cell F-Paging Level
Cell F-QPCH Level
Cell F-BCCH Level
Cell F-CCCH Level
Cell F-FCH/Traffic Level
Cell F-SCH Level
(see How Do I Change Generator Information? and Configuring Forward Channel Power Levels and Walsh Codes )
Traffic Ec/Ior (dB)

Cell F-FCH/Traffic Level (see How Do I Change Generator Information? )
Eb/Nt (dB)

It is not directly settable. It is calculated according to other specified parameters. See TIA-EIA/98-E test standard for details on calculation equations for the specific code channels.

Example Settings

The following table is an example settings as specified in the standard. It also shows how to set on the test set to achieve the specified values. The Ioc, Traffic Ec/Ior, and Pilot Ec/Ior are all directly settable on the test set. For Ior/Ioc, which is the ratio of cell power to AWGN, you need to adjust Cell 1 Power (for Channel 1) and Cell 2 Power (for Channel 2) to achieve the correct levels relative to AWGN.

Test Parameters for Candidate Set Pilot Detection
Parameters in Standard Units Test 1

Equivalent Settings on the Test Set
Ior/Ioc dB -3.1

Set Cell Power to - 58.1 dBm/1.23 MHz (Ioc + Ior/Ioc)
Pilot Ec/Ior dB -7 Set Cell F-Pilot Level to -7 dB
Traffic Ec/Ior dB -7

Set Cell F-FCH/Traffic Level to -7 dB
Ioc dBm/1.23 MHz -55

Set AWGN Power to -55 dBm/1.23 MHz.

Top of pagetop of page     

+
Privacy Statement | Terms of Use | Webmaster  +  © Agilent 2000-2008
+