8960 GSM/GPRS/EGPRS Online User's Guide

E1968A, E6701F, E6704A

Contents

Call Processing

Manual Operation

Protocol Logging

Troubleshooting

Downloadable Manual

CALL:PPRocedure:PMEasurement:PIPE

Last updated: May 19, 2009

GPIB Command Conventions

CALL:PPRocedure:PMEasurement:PIPE

Function	GSM TA	This command is not applicable to the GSM Test Application.
	GPRS TA	This command is not applicable to the GPRS Test Application.
	EGPRS TA	This command is not applicable to the EGPRS Test Application.
	GSM/GPRS LA	Sets or queries the state of the RRLP pipe. When the RRLP pipe mode is enabled, the test set's RRLP message based E-OTD testing is disabled. E-OTD RRLP messages can still be sent, but not encoding or decoding of messages is provided by the test set.
	EGPRS LA
Setting		0\|OFF\|1\|ON
Query		0 \| 1
*RST setting		0
Requirements	GSM/GPRS/ EGPRS LA	Revision: C.03 and above
Programming Example: OUTPUT 714;"CALL:PPRocedure:PMEasurement:PIPE ON"

CALL:PPRocedure:PMEasurement:PIPE:DATA:RX?

Function	GSM TA	This command is not applicable to the GSM Test Application.
	GPRS TA	This command is not applicable to the GPRS Test Application.
	EGPRS TA	This command is not applicable to the EGPRS Test Application.
	GSM/GPRS LA	Queries the raw data from the last RRLP message received from a mobile station. The maximum length of the RRLP message is controlled by the RRLP Header State. See CALL:PPRocedure:PMEasurement:PIPE:HEADer[:STATe] .
	EGPRS LA
Query		Range: A string of 0 to 2000 hexadecimal characters when the RRLP Header state is set to ON. A string of 0 to 251 hexadecimal characters when the RRLP Header state is set to OFF.
*RST setting		""
Requirements	GSM/GPRS/ EGPRS LA	Revision: C.03 and above
Programming Example: OUTPUT 714;"CALL:PPRocedure:PMEasurement:PIPE:DATA:RX?"

CALL:PPRocedure:PMEasurement:PIPE:DATA:RX:AVAilable?

Function	GSM TA	This command is not applicable to the GSM Test Application.
	GPRS TA	This command is not applicable to the GPRS Test Application.
	EGPRS TA	This command is not applicable to the EGPRS Test Application.
	GSM/GPRS LA	Queries whether a response to the last message transmitted to the mobile station using the RRLP pipe has been received and if receiver results are available.
	EGPRS LA
Query		0\|1
*RST setting		0
Requirements	GSM/GPRS/ EGPRS LA	Revision: C.03 and above
Programming Example: OUTPUT 714;"CALL:PPRocedure:PMEasurement:PIPE:DATA:RX:AVA?"

CALL:PPRocedure:PMEasurement:PIPE:DATA:RX:TSTamp?

Function	GSM TA	This command is not applicable to the GSM Test Application.
	GPRS TA	This command is not applicable to the GPRS Test Application.
	EGPRS TA	This command is not applicable to the EGPRS Test Application.
	GSM/GPRS LA	Query the received RRLP pipe message with it's associated GSM frame number. The resolution of both the transmit and receive times is one GSM frame period (4.615mS). This is an extension to the existing CALL:PPRocedure:PMEasurement:PIPE:DATA:RX? command which returns only the <string> with no frame number. See Time To First Fix (TTFF) response time
	EGPRS LA
Query		Range: A string of 0 to 2000 hexadecimal characters, NAN, 0 to 2715647
*RST setting		NAN
Requirements	GSM/GPRS/ EGPRS LA	Revision: G.00.08 and above
Programming Example: OUTPUT 714;"CALL:PPRocedure:PMEasurement:PIPE:DATA:RX:TST?"

CALL:PPRocedure:PMEasurement:PIPE:DATA:TX

Function	GSM TA	This command is not applicable to the GSM Test Application.
	GPRS TA	This command is not applicable to the GPRS Test Application.
	EGPRS TA	This command is not applicable to the EGPRS Test Application.
	GSM/GPRS LA	Sets or queries the string of data to be sent using the RRLP pipe. The data should be formatted as hexadecimal characters and can be up to 2000 characters long. The maximum length of the RRLP message is controlled by the RRLP Header State. See CALL:PPRocedure:PMEasurement:PIPE:HEADer[:STATe]
	EGPRS LA
Setting		Range: 0 to 2000 ASCII formatted hexadecimal characters when the RRLP Header state is set to ON. 0 to 251 ASCII formatted hexadecimal characters when the RRLP Header state is set to OFF.
Query		Range: 0 to 2000 ASCII formatted hexadecimal characters.
*RST setting		""
Requirements	GSM/GPRS/ EGPRS LA	Revision: C.03 and above
Programming Example: OUTPUT 714;"CALL:PPRocedure:PMEasurement:PIPE:DATA:TX `00000000000000000000000000'"

CALL:PPRocedure:PMEasurement:PIPE:HEADer[:STATe]

Function	GSM TA	This command is not applicable to the GSM Test Application.
	GPRS TA	This command is not applicable to the GPRS Test Application.
	EGPRS TA	This command is not applicable to the EGPRS Test Application.
	GSM/GPRS LA	Sets or queries the RRLP Header State which controls the automatic header creation and segmentation of the RRLP pipe message.
	EGPRS LA
Setting		Range: 1\|ON\|0\|OFF
Query		Range: 0\|1
*RST setting		1\|ON
Requirements	GSM/GPRS/ EGPRS LA	Revision: F.00.37 and above
Programming Example: OUTPUT 714;"CALL:PPRocedure:PMEasurement:PIPE:HEADer:STATe ON" ! Set the RRLP Header State to ON.

CALL:PPRocedure:PMEasurement:PIPE:RTIMe

Function	GSM TA	This command is not applicable to the GSM Test Application.
	GPRS TA	This command is not applicable to the GPRS Test Application.
	EGPRS TA	This command is not applicable to the EGPRS Test Application.
	GSM/GPRS LA	Sets or queries the maximum amount of time to wait for a response from the mobile station when sending it information using the RRLP pipe.
	EGPRS LA
Setting		Range:0 to 140 seconds Resolution: 1 second
Query		Range:0 to 140 seconds Resolution: 1 second
*RST setting		10
Requirements	GSM/GPRS/ EGPRS LA	Revision: C.03 and above
Programming Example: OUTPUT 714;"CALL:PPRocedure:PMEasurement:PIPE:RTIMe 60"

CALL:PPRocedure:PMEasurement:PIPE:SEND

Function	GSM TA	This command is not applicable to the GSM Test Application.
	GPRS TA	This command is not applicable to the GPRS Test Application.
	EGPRS TA	This command is not applicable to the EGPRS Test Application.
	GSM/GPRS LA	Sends the data setup using the CALL:PPRocedure:PMEasurement:PIPE:DATA:TX command to the mobile station using the RRLP pipe. This command also clears the results returned by the CALL:PPRocedure:PMEasurement:PIPE:DATA:RX:AVAilable? command.
	EGPRS LA
Requirements	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example: OUTPUT 714;"CALL:PPRocedure:PMEasurement:PIPE:SEND"

CALL:PPRocedure:PMEasurement:PIPE:SEND:EVENt

Function	GSM TA	This command is not applicable to the GSM Test Application.
	GPRS TA	This command is not applicable to the GPRS Test Application.
	EGPRS TA	This command is not applicable to the EGPRS Test Application.
	GSM/GPRS LA	This command sets/queries the Network Event at which the RRLP pipe data will be sent. Backwards compatibility is achieved by setting the default RRLP event type to `None'. See Event Based RRLP for more information
	EGPRS LA
Setting		Range: ASSignment \| NONe \| HANDover \| RRRelease \| LUPDate
Query		Range: ASSignment \| NONe \| HANDover \| RRRelease \| LUPDate
*RST Setting		NONe
Requirements	GSM/GPRS/ EGPRS LA	Revision: G.00.08 and above
Programming Example: OUTPUT 714;"CALL:PPRocedure:PMEasurement:PIPE:SEND:EVENt ASS"

CALL:PPRocedure:PMEasurement:PIPE:SEND:EVENt:TIMeout

Function	GSM TA	This command is not applicable to the GSM Test Application.
	GPRS TA	This command is not applicable to the GPRS Test Application.
	EGPRS TA	This command is not applicable to the EGPRS Test Application.
	GSM/GPRS LA	This command sets/queries the maximum time to wait for the configured event type occur. See Event Based RRLP for more information
	EGPRS LA
Setting		Range: 0 to 600 seconds
Query		Range: 0 to 600 seconds
*RST Setting		300
Requirements	GSM/GPRS/ EGPRS LA	Revision: G.00.08 and above
Programming Example: OUTPUT 714;"CALL:PPRocedure:PMEasurement:PIPE:SEND:EVEN:TIM 10"

CALL:PPRocedure:PMEasurement:PIPE:SEND:TSTamp?

Function	GSM TA	This command is not applicable to the GSM Test Application.
	GPRS TA	This command is not applicable to the GPRS Test Application.
	EGPRS TA	This command is not applicable to the EGPRS Test Application.
	GSM/GPRS LA	Query the GSM frame number of the last transmitted RRLP pipe message. The resolution is 1 GSM frame (4.615ms). See Time To First Fix (TTFF) response time
	EGPRS LA
Query		Range: NAN, 0 to 2715647
*RST Setting		NAN
Requirements	GSM/GPRS/ EGPRS LA	Revision: G.00.08 and above
Programming Example: OUTPUT 714;"CALL:PPRocedure:PMEasurement:PIPE:SEND:TST?"

CALL:PPRocedure:PMEasurement:PIPE:SEND:TSTamp:CLEar

Function	GSM TA	This command is not applicable to the GSM Test Application.
	GPRS TA	This command is not applicable to the GPRS Test Application.
	EGPRS TA	This command is not applicable to the EGPRS Test Application.
	GSM/GPRS LA	Clear the RRLP pipe message send frame number. Then the transmit timestamp is reset to NAN. See Time To First Fix (TTFF) response time
	EGPRS LA
Requirements	GSM/GPRS/ EGPRS LA	Revision: G.00.08 and above
Programming Example: OUTPUT 714;"CALL:PPRocedure:PMEasurement:PIPE:SEND:TST:CLE"