RFANalyzer

Function

GSM TA

Sets/queries which channel (RACH, TCH or PDTCH) is measured when the operating mode is GSM BCH, GPRS BCH or EGPRS BCH. See Measurement Channel in BCH Only Mode .

EGPRS TA

GSM/GPRS LA

EGPRS LA

Setting

Query

Range: RACH | TCH | PDTCh

Revision: A.07 and above

Revision: E.01 and above

Programming Example

 
OUTPUT 714;"RFANalyzer:CONTrol:BTESt:CHANnel TCH" 
! Sets the Measurement Channel in BCH Only Mode to TCH.

Function

GSM TA

Sets/queries whether the test set's receiver is set to automatic (AUTO ON) or manual (AUTO OFF) measurement frequency control. See Receiver Control .

EGPRS TA

GSM/GPRS LA

EGPRS LA

Setting

Query

Range: 1 | 0

Revision: A.01 and above

Revision: C.01 and above

Programming Example

 
OUTPUT 714;"RFANalyzer:CONTrol:MEASurement:FREQuency:AUTO OFF" 
! Enables manual control of the measurement receiver's frequency.

Function

GSM TA

Sets/queries whether the test set receiver's expected power setting is set to automatic (AUTO ON) or manual (AUTO OFF) power control. See Receiver Control .

GPRS TA

EGPRS TA

GSM/GPRS LA

EGPRS LA

Setting

Range: 1 | ON | 0 | OFF

Query

Range: 1 | 0

Revision: A.01 and above

Revision: C.01 and above

Programming Example

 
OUTPUT 714;"RFANalyzer:CONTrol:POWer:AUTO OFF"

Function

GSM TA

Sets/queries whether the test set's demodulation receiver is set to automatic (AUTO ON) or manual (AUTO OFF) uplink frequency control. See Receiver Control .

GPRS TA

EGPRS TA

GSM/GPRS LA

EGPRS LA

Setting

Range: 1 | ON | 0 | OFF

Query

Range: 1 | 0

Revision: A.01 and above

Revision: C.01 and above

Programming Example

 
OUTPUT 714;"RFANalyzer:CONTrol:UPLink:FREQuency:AUTO OFF" 
! The test set's demodulation receiver is set to manual uplink frequency control.

Function

GSM TA

Sets/queries the power level in DBM that the mobile station is expected to transmit in CW mode. The units DBM are optional. The test set will set up its input signal path to measure this power level. See Expected Power Control .

GPRS TA

EGPRS TA

GSM/GPRS LA

EGPRS LA

Setting

Range: -60 to +53 dBm, after the Amplitude Offset (optional) has been factored in. see Amplitude Offset .

Resolution: 0.01 dBm

Query

Range: -60 to +53 dBm, after the Amplitude Offset (optional) has been factored in. see Amplitude Offset .

Resolution: 0.01 dBm

Expected Power: +13 dBm

Revision: A.01 and above

Revision: C.01 and above

Programming Example

 
OUTPUT 714;"RFANalyzer:CW:EXPected:POWer -20 DBM" 
! Sets the expected power transmit level to -20 dBm.

Function

GSM TA

This command automatically sets the receiver to manual mode and changes the measurement frequency, which is used to tune the test set's measuring receiver.

GPRS TA

EGPRS TA

GSM/GPRS LA

Setting

Range: 292.5 MHz to 2700 MHz

Resolution: 1 Hz

Query

Range: 292.5 MHz to 2700 MHz

Resolution: 1 Hz

Revision: A.01 and above

Revision: C.01 and above

Programming Example

 
OUTPUT 714;"RFANalyzer:MANual:MEASurement:MFRequency 942.6 MHZ" 
! Enables manual receiver control and sets the test set's receiver frequency to 942.6 MHz.

Function

GSM TA

Sets/queries the frequency used to tune the test set's measuring receiver, when manual mode is selected (RFANalyzer:CONTrol:MEASurement:FREQuency:AUTO OFF).

GPRS TA

EGPRS TA

GSM/GPRS LA

EGPRS LA

Setting

Range: 292.5 MHz to 2700 MHz

Resolution: 1 Hz

Query

Range: 292.5 MHz to 2700 MHz

Resolution: 1 Hz

Revision: A.01 and above

Revision: C.01 and above

Programming Example

 
OUTPUT 714;"RFANalyzer:MANual:MEASurement:FREQuency 942.6 MHZ" 
! Sets the test set's receiver frequency to 942.6 MHz when manual control is used.

Function

GSM TA

This command sets/queries the power level in dBm that the test set's receiver is expecting the mobile station uplink burst to transmit at for the active (that is the selected) format.

This setting applies when the Multislot Configuration setting allows the number of uplink bursts that you wish to set, or Uplink Test Sequence Burst Count (while in FastTune operating mode) is at least as high as the burst power you wish to set.

Bursts 5 through 8 only apply when the operating mode is set to FastTune .

Note: Only burst 1 is applicable to GSM TCH measurements.

GPRS TA

EGPRS TA

GSM/GPRS LA

EGPRS LA

Setting

Range: -60 dBm to +53 dBm, after the Amplitude Offset (optional) has been included, see Amplitude Offset .

Resolution: 0.01 dBm

Query

Range: -60 dBm to +53 dBm, after the Amplitude Offset (optional) has been included, see Amplitude Offset .

Resolution: 0.01 dBm

13 dBm

Revision: A.01 and above

Revision A.03 adds Burst3 and Burst4

Revision A.04 adds Burst 5 through 8.

Revision: C.01 and above

Revision D.01 adds Burst3 and Burst4

Revision E.01 adds Burst 5 through 7.

Programming Example

 
OUTPUT 714;"RFANalyzer:MANual:POWer:BURSt 7" 
! Sets the test set expected burst power of the first burst level to 7 dBm.

Function

GSM TA

Sets/queries the test set's demodulation receiver frequency, used to demodulate information from the mobile's reverse channel transmission.

GPRS TA

EGPRS TA

GSM/GPRS LA

EGPRS LA

Setting

Range: 292.5 MHz to 2700 MHz

Resolution: 1 Hz

Query

Revision: A.01 and above

Revision: C.01 and above

Programming Example

 
OUTPUT 714;"RFANalyzer:MANual:UPLink:MFRequency 1955.030 MHz" 
! Enables manual demodulation receiver control and sets the test set's 
! demodulation receiver frequency to 1955.030 MHz.

Function

GSM TA

Sets/queries the test set's demodulation receiver frequency used to demodulate information from the mobile's reverse channel transmission when manual mode is selected (RFANalyzer:CONTrol:MEASurement:FREQuency:AUTO OFF).

GPRS TA

EGPRS TA

GSM/GPRS LA

EGPRS LA

Setting

Range: 292.5 MHz to 2700 MHz

Resolution: 1 Hz

Query

Range: 292.5 MHz to 2700 MHz

Resolution: 1 Hz

Revision: A.01 and above

Revision: C.01 and above

Programming Example

 
OUTPUT 714;"RFANalyzer:MANual:UPLink:FREQuency 942.6 MHZ" 
! Sets the test set's demodulation receiver frequency to 942.6 MHz.