|
|
SETup:ORFSpectrum
Last updated: December 3, 2008
GPIB Command Conventions
SETup:ORFSpectrum:AUTO:FILTer:TYPE?
|
Function
|
GSM TA
|
Queries the test set to determine the fastest measurement filter type based on the currently installed hardware and test set configuration. The possible measurement filter types are
ANALog
and
DIGital
. See
Output RF Spectrum Measurement Description
for more information regarding the measurement filter type and other information on the ORFS measurement.The result of this query is the type of measurement filter the test set uses if the measurement filter type is set to
AUTO
.
The command to set the measurement filter type is
SETup:ORFSpectrum:FILTer:TYPE
.
For more information on how the hardware affects the measurement filter type, see:
http://www.agilent.com/find/8960upgrades
|
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range: ANALog|DIGital
|
|
Query
|
Range: ANALog|DIGital
|
|
*RST Setting |
ANAL |
|
Requirements
|
GSM/GPRS/
EGPRS TA
|
Revision: A.06 and above
|
|
GSM/GPRS/ EGPRS LA
|
Revision: D.03 and above |
|
Programming Example
OUTPUT 714;"SETup:ORFSpectrum:AUTO:FILTer:TYPe?"
! Queries the ORFS modulation measurement filter type that would give the fastest measurement results.
|
SETup:ORFSpecturm:CONTinuous
|
Function
|
GSM TA
|
This command selects/queries the trigger state for output RF spectrum measurements.
|
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range:
-
Continuous trigger mode = 1 | ON
-
Single trigger mode = 0 | OFF
|
|
Query
|
Range: 1 | 0
|
|
*RST Setting |
1 | ON |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.02 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.02 and above
|
|
Programming Example
OUTPUT 714;"ABORT:ALL"
! Aborts all active measurements in progress.
OUTPUT 714;"SETUP:CONTINUOUS OFF"
! Sets trigger mode to single for an ORFS measurement.
|
SETup:ORFSpectrum:COUNt:STATe
|
Function
|
GSM TA
|
This command selects/queries the ORFS due to switching and modulation multi-measurement count state.
|
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range: 0 | OFF | 1 | ON
|
|
Query
|
Range: 0 | 1
|
|
*RST Setting |
1 | ON |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.02 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.02 and above
|
|
Programming Example
OUTPUT 714;"SETUP:ORFSPECTRUM:COUNT:STATE ON"
! Sets count state for both ORFS due to switching and modulation measurements.
|
SETup:ORFSpectrum:FAST
|
Function
|
GSM TA
|
This command sets/queries the fast measurement state, which determines whether or not the ORFS due to modulation measurement is performed exactly as defined in the ETSI standards.
When set to On, the measurement is performed on both the front and back sections of the burst. With this setting, the test set can provide two modulation measurements per burst, effectively doubling measurement throughput.
When set to Off, the measurement is only performed on the latter section of the burst as defined in the ETSI GSM standards.
When the ORFS measurement filter type (
SETup:ORFSpectrum:FILTer:TYPE
) is set to
DIGital
the measurement ignores the fast measurement state if the expected power for the selected burst is lower than the expected power of the burst that is immediately before it.
|
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range: 0 | OFF | 1 | ON
|
|
Query
|
Range: 0 | 1
|
|
*RST Setting |
1 | ON |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.03 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.03 and above
|
|
Programming Example
OUTPUT 714;"SETUP:ORFSPECTRUM:FAST OFF"
! Sets the ORFS modulation measurement to be performed exactly as defined in the ETSI standards.
|
SETup:ORFSpectrum:FILTer:TYPE
|
Function
|
GSM TA
|
Sets/Queries the filter type. The possible measurement filter options are Analog, Digital, and AUTO.
The analog and digital measurement filter types each include ORFS due to modulation and ORFS due to switching. When set to AUTO, the test set automatically selects the filter type that will result in the fastest measurement speed based on the test set's hardware specification and the current test set configuration. The filter type chosen by the test set can be queried using the command
SETup:ORFSpectrum:AUTO:FILTer:TYPE?
. See also
Output RF Spectrum Measurement Description
for more information regarding the measurement filter type and other information on the ORFS measurement.
|
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range: ANALog|AUTO|DIGital
|
|
Query
|
Range: ANALog|AUTO|DIGital
|
|
*RST Setting |
ANAL |
|
Requirements
|
GSM/GPRS/
EGPRS TA
|
Revision: A.06 and above
|
|
GSM/GPRS/ EGPRS LA
|
Revision: D.03 and above |
|
Programming Example
OUTPUT 714;"SETup:ORFSpectrum:FILTer:TYPe AUTO"
! Allows the test set to determine which measurement type was the fastest.
! The measurement filter type that is used is what the test set returns from the query
! SETup:ORFSpectrum:AUTO:FILTer:TYPE?
|
SETup:ORFSpectrum:ICOunt:MAXimum?
|
Function
|
GSM TA
|
This command queries the total number of measurements made each time an ORFS measurement is initiated. This number will vary depending on the number of offsets and number of multi-measurements that you choose.
The total number of measurements is calculated using the following formula:
ICO MAX = 1 + M + S
-
Where:
-
M= (
the number of modulation offsets
) ¥ (
the number of multi-measurements for ORFS due to modulation
).
-
S= (
the number of switching offsets
) ¥ (
the number of multi-measurements for ORFS due to switching
).
See
Output RF Spectrum Measurement Description
for a description of modulation and switching offsets.
|
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Query
|
Range: 1 to 30970
Resolution: 1
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
SETup:ORFSpectrum:LIMit:SOURce
|
Function
|
GSM TA
|
This command selects whether the ORFS measurement uses the ETSI defined limits, or user-defined limits you have specified using the MANual or CUSTom commands.
This command is implemented in the active (that is the selected) format.
|
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range: ETSI | MANual[1] | MANual2|CUSTom[1]| CUSTom2|NOMask
|
|
Query
|
Range: ETSI | MAN | MAN2|CUST| CUST2|NOMask
|
|
*RST Setting |
ETSI |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714"SETUP:ORFSPECTRUM:LIMIT:SOURCE MAN"
! Allows you to manually set the limits.
|
SETup:ORFSpectrum:MODulation:ABSolute:LIMit:CUSTom<[1]|2>
|
Function
|
GSM TA
|
This command sets/queries the absolute limits for the specified custom mask to be used with the ORFS Modulation measurement. Custom limit testing differs from Manual limit testing because a limit mask is defined separately from the frequency offset. When a frequency offset is changed, the limit value is recalculated for the new frequency offset by interpolating the Custom Mask.
A total of 32 reference points (frequency point / limit value mask point pairs) are available to you when defining a custom mask. Frequency Offsets that fall outside the Custom Mask will always return a PASS result. The custom mask is turned off when no points are specified in this command.
|
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range:
0 to 32 comma-separated value pairs containing frequency point and limit value within the following ranges:
-
Frequency: -1800Hz to -10Hz and +10Hz to +1800kHz
-
Limit Value: -200dBm to +100dBm
Resolution:
-
Frequency: 10 Hz
-
Limit Value: 0.1 dB
|
|
Query
|
Range:
0 to 32 comma-separated value pairs containing frequency point and limit value within the following ranges:
-
Frequency: -1800Hz to -10Hz, +10Hz to +1800kHz, and 9.91E+37 (NAN) if no offsets are specified.
-
Limit Value: -200dBm to +100dBm
Resolution:
-
Frequency: 10 Hz
-
Limit Value: 0.1 dB
|
|
*RST Setting |
No Mask |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.03 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.03 and above
|
SETup:ORFSpectrum:MODulation:ABSolute:LIMit:CUSTom<[1] |2>:POINts?
|
Function
|
GSM TA
|
This query returns the number of enabled reference points for the ORFS Modulation Absolute custom mask you specify.
|
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Query
|
Range: 0 to 32
Resolution: 1
|
|
*RST Setting |
0 |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.03 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.03 and above
|
SETup:ORFSpectrum:MODulation:COUNt[:SNUMber]
|
Function
|
GSM TA
|
This command sets/queries the number of ORFS due to modulation multi-measurements the test set will make. This command sets the count state to ON.
|
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range: 1 to 999
Resolution: 1
|
|
Query
|
Range: 1 to 999
Resolution: 1
|
|
*RST Setting |
20
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714"SETUP:ORFSPECTRUM:MODULATION:COUNT:SNUMBER 99"
! Sets the value to 99 multi-measurements and the state to on.
|
SETup:ORFSpectrum:MODulation:COUNt:NUMBer
|
Function
|
GSM TA
|
This command sets/queries the number of ORFS due to modulation multi-measurements the test set will make when the multi-measurement count state is on. See
Output RF Spectrum Measurement Description
. |
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range: 1 to 999
Resolution: 1
|
|
Query
|
Range: 1 to 999
Resolution: 1
|
|
*RST Setting |
20 |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:ORFSPECTRUM:MODULATION:COUNT:NUMBER 75"
! Sets the multi-measurement count number for ORFS due to modulation measurements to 75.
|
SETup:ORFSpectrum:MODulation:FREQuency[:OFFSet]
|
Function
|
GSM TA
|
This command sets/queries the list of ORFS due to modulation frequency offsets. Each offset listed in the command is turned on by default. If no frequency offsets (null list) are sent, the output RF spectrum due to modulation measurement will not be made. The units (GHZ|MHZ|KHZ|HZ) are optional, if no units are specified than units default to HZ. see
Output RF Spectrum Measurement Description
. |
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range: 0 to 22 comma-separated values ranging from -1.8 MHz to -10 Hz, and +10 Hz to +1.8 MHz
Resolution: 10 Hz
|
|
Query
|
Range: 0 to 22 comma-separated values ranging from -1.8 MHz to -10 Hz, and +10 Hz to +1.8 MHz
Resolution: 10 Hz
|
|
*RST Setting |
Offset 1: 400.0 kHz
Offset 2: 600.0 kHz
Offsets 3 to 22: off
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:ORFSPECTRUM:MODULATION:FREQUENCY:OFFSET 400 KHZ, 700 KHZ"
! Turns on the first two ORFS due to modulation measurement offsets and sets
! them to 400 kHz and 700 kHz offsets. All other offsets are in the off state.
OUTPUT 714;"SETUP:ORFSPECTRUM:MODULATION:FREQUENCY:OFFSET 700 KHZ"
! Turns on the first ORFS due to modulation measurement offset and sets it to A 700 kHz
! offset. All other offsets are in the off state.
OUTPUT 714;"SETUP:ORFSPECTRUM:MODULATION:FREQUENCY:OFFSET"
! Turns all offsets for ORFS due to modulation measurement to the off state.
|
SETup:ORFSpectrum:MODulation:FREQuency:OFFSet:ALL
|
Function
|
GSM TA
|
This command turns on or off all of the frequency offsets for the ORFS Modulation measurement. |
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range: 0 | OFF | 1 | ON
|
|
*RST Setting |
Offset 1: On
Offset 2: On
Offsets 3 to 22: Off
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
SETup:ORFSpectrum:MODulation:FREQuency:POINts?
|
Function
|
GSM TA
|
This command queries the number of frequency offsets currently on during an ORFS due to modulation measurement in the active (that is the selected) format. See
Output RF Spectrum Measurement Description
.
|
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Query
|
Range: 0 to 22
Resolution: 1
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
SETup:ORFSpectrum:MODulation:LIMit:MANual<[1]|2>[:SELected]
SETup:ORFSpectrum:MODulation:LIMit:MANual<[1]|2>:(DCS|EGSM|GSM450|GSM480|GSM750|GSM850|PCS|PGSM|RGSM|TGSM810)
|
Function
|
GSM TA
|
This command allows you to set the specified manual limits for the ORFS due to modulation measurement. You can enter up to 22 limit values, one for each of the ORFS due to modulation offset frequencies. The n
th
limit value is the value for the n
th
offset frequency, regardless of whether the offset frequency is switched on or off. Changing the offset value has no effect on the limit value. If you supply fewer than 22 limit values, the remainder of the limit values remain unchanged.
The optional [:SELected] node allows you to select which traffic channel band the setting is implemented in. The default band is the currently selected band, otherwise you can specify PGSM, EGSM, DCS, PCS, RGSM, GSM450, GSM480, GSM750, GSM850, or TGSM810.
|
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range: 1 to 22 comma-separated values ranging from -200 dB to +100 dB
Resolution: 0.1
|
|
Query
|
Range: 22 comma-separated values ranging from -200 dB to +100 dB
Resolution: 0.1
|
|
*RST Setting |
Offset 1: -60 dB
Offset 2: -60 dB
Offset 3: +0.5 dB
Offset 4: +0.5 dB
Offset 5: -30 dB
Offset 6: -30 dB
Offset 7: -33 dB
Offset 8: -33 dB
Offset 9: -60 dB
Offset 10: -60 dB
Offset 11: -60 dB
Offset 12: -60 dB
Offset 13: -60 dB
Offset 14: -60 dB
Offset 15: -60 dB
Offset 16: -60 dB
Offset 17: -60 dB
Offset 18: -60 dB
Offset 19: -60 dB
Offset 20: -60 dB
Offset 21: -60 dB
Offset 22: -60 dB
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
Revision A.06 adds the TGSM810 band.
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
Revision D.03 adds the TGSM810 band.
|
|
Programming Example
OUTPUT 714;"SETUP:ORFSPECTRUM:MODULATION:LIMIT:MANUAL -58DB,-58DB"
! Sets the first two offsets to -58 dB and -58 dB respectively.
|
SETup:ORFSpectrum:MODulation:RELative:LIMit:CUSTom<[1]|2>
|
Function
|
GSM TA
|
This command sets/queries the relative limits for the specified custom mask to be used with the ORFS Modulation measurement. Custom limit testing differs from Manual limit testing because a limit mask is defined separately from the frequency offset. When a frequency offset is changed, the limit value is recalculated for the new frequency offset by interpolating the Custom Mask.
A total of 32 reference points (frequency point / limit value mask point pairs) are available to you when defining a custom mask. Frequency Offsets that fall outside the Custom Mask will always return a PASS result.
|
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range:
0 to 32 comma-separated value pairs containing frequency point and limit value within the following ranges:
-
Frequency: -1800 Hz to -10 Hz and +10 Hz to +1800 kHz
-
Limit Value: -200 dB to +100 dB
Resolution:
-
Frequency: 10 Hz
-
Limit Value: 0.1 dB
|
|
Query
|
Range:
0 to 32 comma-separated value pairs containing frequency point and limit value within the following ranges:
-
Frequency: -1800 Hz to -10 Hz, +10 Hz to +1800 kHz, and 9.91E+37 (NAN) if no offsets are specified.
-
Limit Value: -200 dB to +100 dB
Resolution:
-
Frequency: 10 Hz
-
Limit Value: 0.1 dB
|
|
*RST Setting |
No Mask |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.03 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.03 and above
|
SETup:ORFSpectrum:MODulation:RELative:LIMit:CUSTOM<[1]|2>:POINts?
|
Function
|
GSM TA
|
This query returns the number of enabled reference points for the ORFS Modulation Relative custom mask you specify.
|
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Query
|
Range: 0 to 32
Resolution: 1
|
|
*RST Setting |
0 |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.03 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.03 and above
|
SETup:ORFSpectrum:SWITching:COUNt[:SNUMber]
|
Function
|
GSM TA
|
This command sets/queries the ORFS due to switching multi-measurement count value and turns the state on.
|
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range: 1 to 999
Resolution: 1
|
|
Query
|
Range: 1 to 999
Resolution: 1
|
|
*RST Setting |
10 |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:COUNT:SNUMBER 55"
! Sets the multi-measurment value to 10 and the state to on.
|
SETup:ORFSpectrum:SWITching:COUNt:NUMBer
|
Function
|
GSM TA
|
This command sets/queries the ORFS due to switching multi-measurement count value. See
Output RF Spectrum Measurement Description
. |
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA |
|
Setting |
Range: 1 to 999
Resolution: 1
|
|
Query
|
Range: 1 to 999
Resolution: 1
|
|
*RST Setting |
10 |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:COUNT:NUMBER 15"
! Sets the multi-measurement count number for ORFS due to switching to 15.
|
SETup:ORFSpectrum:SWITching:FREQuency[:OFFSet]
|
Function
|
GSM TA
|
This command sets/queries the list of ORFS due to switching frequency offsets in the active (that is the selected) format. Each offset listed in the command is turned on by default. If no frequency offsets (null list) are sent, the output RF spectrum due to switching measurement will not be made. The units (GHZ|MHZ|KHZ|HZ) are optional, if no units are specified than units default to HZ. See
Output RF Spectrum Measurement Description
. |
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range: 0 to 8 comma-separated values ranging from -1.8 MHz to -10 Hz, and +10 Hz to +1.8 MHz
Resolution: 10 Hz
|
|
Query
|
Range: 0 to 8 comma-separated values ranging from -1.8 MHz to -10 Hz, and +10 Hz to +1.8 MHz
Resolution: 10 Hz
|
|
*RST Setting |
Offset 1 = 400.0 kHz
Offset 2 = 600.0 kHz
Offsets 3 to 8 off
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:FREQUENCY:OFFSET 400 KHZ, 700 KHZ"
! Turns on the first two ORFS due to switching measurement offsets and sets them
! to 400 kHz and 700 kHz offsets. All other offsets are in the off state.
OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:FREQUENCY:OFFSET 700 KHZ"
! Turns on the first ORFS due to switching measurement offset and sets it to 700 kHz
! offsets. All other offsets are in the off state.
OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:FREQUENCY:OFFSET"
! Turns all of the ORFS due to switching measurements offsets to off.
|
SETup:ORFSpectrum:SWITching:FREQuency:OFFSet:ALL
|
Function
|
GSM TA
|
This command turns on or off all of the frequency offsets for the ORFS Switching measurement. |
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range: 0 | OFF | 1 | ON
|
|
*RST Setting |
Offset 1: On
Offset 2: On
Offsets 3 to 8: Off
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
SETup:ORFSpectrum:SWITching:FREQuency:POINts?
|
Function
|
GSM TA
|
This command queries the number of frequency offsets currently on during an ORFS due to switching measurement. See
Output RF Spectrum Measurement Description
. |
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Query
|
Range: 0 to 8
Resolution: 1
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
SETup:ORFSpectrum:SWITching:LIMit:CUSTom
|
Function
|
GSM TA
|
This command sets/queries the absolute limits for the custom mask to be used with the ORFS Switching measurement. Custom limit testing differs from Manual limit testing because a limit mask is defined separately from the frequency offset. When a frequency offset is changed, the limit value is recalculated for the new frequency offset by interpolating the Custom Mask.
A total of 32 reference points (frequency point / limit value mask point pairs) are available to you when defining a custom mask. Frequency Offsets that fall outside the Custom Mask will always return a PASS result.
|
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range:
0 to 32 comma-separated value pairs containing frequency point and limit value within the following ranges:
-
Frequency: -1800 Hz to -10H z and +10 Hz to +1800 kHz
-
Limit Value: -200 dBm to +100 dBm
Resolution:
-
Frequency: 10 Hz
-
Limit Value: 0.1 dB
|
|
Query
|
Range:
0 to 32 comma-separated value pairs containing frequency point and limit value within the following ranges:
-
Frequency: -1800 Hz to -10 Hz, +10 Hz to +1800 kHz, and 9.91E+37 (NAN) if no offsets are specified.
-
Limit Value: -200 dBm to +100 dBm
Resolution:
-
Frequency: 10 Hz
-
Limit Value: 0.1 dB
|
|
*RST Setting |
No Mask |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.03 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.03 and above
|
SETup:ORFSpectrum:SWITching:LIMit:CUSTom:POINts?
|
Function
|
GSM TA
|
This query returns the number of enabled reference points for the ORFS Switching Absolute custom mask.
|
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Query
|
Range: 0 to 32
Resolution: 1
|
|
*RST Setting |
0 |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.03 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.03 and above
|
SETup:ORFSpectrum:SWITching:LIMit:MANual[:SELected]
SETup:ORFSpectrum:SWITching:LIMit:MANual:(DCS|EGSM|GSM450|GSM480|GSM750|GSM850|PCS|PGSM|RGSM|TGSM810)
|
Function
|
GSM TA
|
This command allows you to set the limits for the ORFS due to switching measurement. You can enter up to eight limit values, one for each of the ORFS due to switching offset frequencies. The n
th
limit value is the value for the n
th
offset frequency, regardless of whether the offset frequency is switched on or off. Changing the offset value has no effect on the limit value. If you supply fewer than eight limit values, the remainder of the limit values remain unchanged.
The optional [:SELected] node allows you to select which traffic channel band the setting is implemented in. The default band is the currently selected band, otherwise you can specify PGSM, EGSM, DCS, PCS, RGSM, GSM450, GSM480, GSM750, GSM850, or TGSM810.
|
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range: 1 to 8 comma-separated values ranging from -200 dBm to +100 dBm
Resolution: 0.1
|
|
Query
|
Range:8 comma-separated values ranging from -200 dBm to +100 dBm
Resolution: 0.1
|
|
*RST Setting |
Offset 1: -23 dBm
Offset 2: -26 dBm
Offset 3: -23 dBm
Offset 4: -26 dBm
Offset 5: -32 dBm
Offset 6: -32 dBm
Offset 7: -36 dBm
Offset 8: -36 dBm
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
Revision A.06 adds the TGSM810 band.
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
Revision D.03 adds the TGSM810 band.
|
|
Programming Example
OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:LIMIT:MANUAL -30DBM,-32DBM"
! Sets the first two offsets to -30 dBm and -32 dBm respectively.
|
SETup:ORFSpectrum:SWITching:TIME:DOMain:STATe
|
Function
|
GSM TA
|
This command sets/queries the Time Domain Trace state for ORFS due to Switching measurement. You can turn on/off the Time Domain Trace by setting this parameter. However, turn on the Time Domain Trace will significantly slow down the measurement speed. |
|
GPRS TA |
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range: 1|ON|0|OFF
|
|
Query
|
Range: 1|0
|
|
*RST Setting |
0|OFF |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.09 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: F.01 and above
|
|
Programming Example
OUTPUT 714;"SET:ORFS:SWIT:TIME:DOM:STAT ON"
! Turn on the Time Domain Trace.
|
SETup:ORFSpectrum:SWITching:TIME:DOMain:FREQuency:OFFSet:INDex
|
Function
|
GSM TA
|
This command sets/queries the frequency that the time domain trace is made on. the frequency is either equal to that of the carrier or an offset towards the carrier. You can use
SETup:ORFSpectrum:SWITching:FREQuency[:OFFSet]
to set the offset value. |
|
GPRS TA |
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range: CARRier|OFFSet1|OFFSet2|OFFSet3|OFFSet4|OFFSet5|OFFSet6| OFFSet7|OFFSet8|CARRier
|
|
Query
|
Range: CARR|OFFS1|OFFS2|OFFS3|OFFS4|OFFS5|OFFS6| OFFS7|OFFS8 |
|
*RST Setting |
CARRier |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.09 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: F.01 and above
|
|
Programming Example
OUTPUT 714;"SETup:ORFSpectrum:SWITching:TIME:DOMain:FREQuency:OFFSet:INDex OFFSet1"
! Sets the Frequency Offset Index to OFFSet1.
|
SETup:ORFSpectrum:TIMeout:TIME
|
Function
|
GSM TA
|
This command selects/queries the timeout value in seconds that will be used for ORFS measurements when the
SETup:ORFSpectrum:TIMeout:STATe
is ON. The units (S | MS) are optional. Units default to S if units are not specified. |
|
GPRS TA |
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range: 0.1 to 999 seconds
Resolution: 0.1 seconds
|
|
Query
|
Range: 0.1 to 999 seconds
Resolution: 0.1 seconds
|
|
*RST Setting |
10 seconds
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:ORFSPECTRUM:TIMEOUT:TIME 15"
! Sets the timeout value to 15 seconds.
|
SETup:ORFSpectrum:TIMeout[:STIMe]
|
Function
|
GSM TA
|
This command sets/queries the timeout value in seconds that will be used for ORFS measurements and turns the timeout state on. The units (S|MS) are optional. If no units are specified than units default to S.
|
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA |
|
Setting |
Range: 0.1 to 999 seconds
Resolution: 0.1 seconds
|
|
Query
|
Range: 0.1 to 999 seconds
Resolution: 0.1 seconds
|
|
*RST Setting |
10 seconds
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:ORFSPECTRUM:TIMEOUT:STIME 12"
! Sets the timeout value to 12 seconds and the state to on.
|
SETup:ORFSpectrum:TIMeout:STATe
|
Function
|
GSM TA
|
This command selects/queries the ORFS measurement timeout state.
|
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range: 0 | OFF | 1 | ON
|
|
Query
|
Range: 0 | 1
|
|
*RST Setting |
0 | OFF |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:ORFSPECTRUM:TIMEOUT:STATE ON"
! Sets timeout state to on.
|
SETup:ORFSpectrum:TRIGer:DELay
|
Function
|
GSM TA
|
This command sets/queries the trigger delay for ORFS measurements. The units (S | MS | US | NS) are optional, units default to S if units are not specified.
|
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range: -2.31 ms to +2.31 ms
Resolution: 5 significant digits or 100 nanoseconds whichever is greater
|
|
Query
|
Range: -2.31 ms to +2.31 ms
Resolution: 5 significant digits or 100 nanoseconds whichever is greater
|
|
*RST Setting |
0 seconds |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:ORFSPECTRUM:TRIGGER:DELAY 1MS"
! Sets the trigger delay value to 1 millisecond.
|
SETup:ORFSpectrum:TRIGger:SOURce
|
Function
|
GSM TA
|
This command selects/queries the trigger source for ORFS measurements. See
Output RF Spectrum Measurement Description
. |
|
GPRS TA
|
|
EGPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA |
|
Setting |
Range: AUTO | IMMediate | PROTocol | RISE | EXTernal
See
Triggering of Measurements
.
|
|
Query
|
Range: AUTO | IMM | PROT | RISE | EXT
|
|
*RST Setting |
AUTO
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:ORFSPECTRUM:TRIGGER:SOURCE AUTO"
! Sets the trigger source to automatic.
|
|
|
top
of page