|
|
SETup:PVTime
Last updated: March 17, 2009
GPIB Command Conventions
SETup:PVTime:BURSt:CAPTure
|
Function
|
GSM TA
|
This command sets/queries the Burst Capture Range for Power versus Time measurement. See
Burst Capture Range
|
|
GPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
EGPRS TA
|
|
Setting |
SINGle | ALL
|
|
Query
|
SING | ALL |
|
*RST Setting |
SINGle |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.08 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: E.02 and above
|
|
Programming Example
OUTPUT 714;"SETup:PVTime:BURSt:CAPTure SINGle"
! Sets Burst Capture Range to SINGle.
|
SETup:PVTime[:BURSt[1]]:MASK[:SELected]
SETup:PVTime:BURSt2|3|4|5|6:MASK[:SELected]
|
Function
|
GSM TA
|
This command sets/queries the type of mask to be used for the specified burst in the single slot or multislot configuration.
Setting this command to ETSI selects the appropriate ETSI compliant mask for the specified burst.
Setting this command to CUSTom1 selects the user-defined CUSTOM 1 mask for the specified burst.
Setting this command to CUSTom2 selects the user-defined CUSTOM 2 mask for the specified burst.
Setting this command to NOMask disables mask checking for the specified burst.
Note that if you want to select a custom mask (CUSTOM 1 or CUSTOM 2), you need to configure the mask settings before use.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
ETSI | CUSTom1|CUSTom2|NOMask
|
|
Query
|
ETSI | CUST1|CUST2|NOM
|
|
*RST Setting |
ETSI
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
Revision: A.08 adds Burst 3 and 4
Revision: A.09 adds Burst 5
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
Revision: E.02 adds Burst 3 and 4
Revision: F.01 adds Burst 5
Revision: G.00.00 adds Burst 6
|
|
Programming Example
OUTPUT 714;"SETUP:PVTIME:BURST:MASK CUSTOM1"
! Sets burst 1 to use the custom1 mask for the pass/fail comparison
|
SETup:PVTime[:BURSt[1]]:MASK:GPERiod
SETup:PVTime:BURSt2|3|4|5:MASK:GPERiod
|
Function
|
GSM TA
|
This command sets/queries the guard period mask type for Power versus Time measurements.
Setting this command to ETSI selects the ETSI compliant mask for the guard period.
Setting this command to CUSTom selects the user-defined CUSTOM mask for the guard period.
Setting this command to NOMask disables mask checking for the guard period.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
ETSI | CUSTom|NOMask
|
|
Query
|
ETSI | CUST||NOM
|
|
*RST Setting |
ETSI
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
Revision: A.08 adds Burst 2 and 3
Revision: A.09 adds Burst 4
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
Revision: E.02 adds Burst 2 and 3
Revision: F.01 adds Burst 4
Revision: G.00.00 adds Burst 5
|
|
Programming Example
OUTPUT 714;"SETUP:PVT:BURST1:MASK:GPERIOD CUSTOM
! Sets the measurement to use the custom guard period settings.
|
SETup:PVTime[:BURSt[1]]:MASK:GPERiod:CUSTom:HIGH
|
Function
|
GSM TA
|
This command sets/queries the custom guard period high level offset. This is the guard period level in dBc relative to the first burst's carrier power level.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
Range: -200 dB to +200 dB
Resolution: 0.01 dB
|
|
Query
|
Range: -200 dB to +200 dB
Resolution: 0.01 dB
|
|
*RST Setting |
+1 dBc (relative to the previous burst)
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:PVTIME:BURST1:MASK:GPERIOD:CUSTOM:HIGH 2"
! Sets the custom guard period high value to be 2 dBc
|
SETup:PVTime[:BURSt[1]]:MASK:GPERiod:CUSTom:LOW
|
Function
|
GSM TA
|
This command sets/queries the custom guard period low level offset. This is the guard period level in dBc relative to the second burst's carrier power level.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
Range: -200 dB to +200 dB
Resolution: 0.01 dB
|
|
Query
|
Range: -200 dB to +200 dB
Resolution: 0.01 dB
|
|
*RST Setting |
+4 dBc (relative to the next burst)
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:PVTIME:BURST1:MASK:GPERIOD:CUSTOM:LOW 5"
! Sets the custom guard period low value to be 5dBc
|
SETup:PVTime[:BURSt[1]]:MASK[:SELected]:LOWer?
SETup:PVTime:BURSt2|3|4|5|6:MASK[:SELected]:LOWer?
|
Function
|
GSM TA
|
This query returns the lower limits for the actual mask being used by the specified burst.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Query
|
Range:
0 to 32 comma-separated triple values containing Time, Relative Power, and Absolute Power within the following ranges:
-
Time: -50 us to 593 us
-
Relative Power and Absolute Power: -200 to +200 dBc and 9.91E+37 (NAN) for Absolute Power values.
Resolution:
-
Time: 1 ns
-
Relative Power and Absolute Power: 0.1 dB
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
Revision: A.08 adds Burst 3 and 4
Revision: A.09 adds Burst 5
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
Revision: E.02 adds Burst 3 and 4
Revision: F.01 adds Burst 5
Revision: G.00.00 adds Burst 6
|
SETup:PVTime[:BURSt[1]]:MASK[:SELected]:LOWer:POINts?
SETup:PVTime:BURSt2|3|4|5|6:MASK[:SELected]:LOWer:POINts?
|
Function
|
GSM TA
|
This query returns the number of reference points for the lower mask being used by the specified burst.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Query
|
Range: 0 to 32
Resolution: 1
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
Revision: A.08 adds Burst 3 and 4
Revision: A.09 adds Burst 5
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
Revision: E.02 adds Burst 3 and 4
Revision: F.01 adds Burst 5
Revision: G.00.00 adds Burst 6
|
SETup:PVTime[:BURSt[1]]:MASK[:SELected]:UPPer?
SETup:PVTime:BURSt2|3|4|5|6:MASK[:SELected]:UPPer?
|
Function
|
GSM TA
|
This query returns the upper limits for the actual mask being used by the specified burst.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Query
|
Range:
0 to 32 comma-separated triple values containing Time, Relative Power, and Absolute Power within the following ranges:
-
Time: -50 us to 593 us
-
Relative Power and Absolute Power: -200 to +200 dBc and 9.91E+37 (NAN) for Absolute Power values.
Resolution:
-
Time: 1 ns
-
Relative Power and Absolute Power: 0.1 dB
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
Revision: A.08 adds Burst 3 and 4
Revision: A.09 adds Burst 5
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
Revision: E.02 adds Burst 3 and 4
Revision: F.01 adds Burst 5
Revision: G.00.00 adds Burst 6
|
SETup:PVTime[:BURSt[1]]:MASK[:SELected]:UPPer:POINts?
SETup:PVTime:BURSt2|3|4|5|6:MASK[:SELected]:UPPer:POINts?
|
Function
|
GSM TA
|
This query returns the number of reference points for the lower mask being used by the specified burst.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Query
|
Range: 0 to 32
Resolution: 1
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
Revision: A.08 adds Burst 3 and 4
Revision: A.09 adds Burst 5
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
Revision: E.02 adds Burst 3 and 4
Revision: F.01 adds Burst 5
Revision: G.00.00 adds Burst 6
|
SETup:PVTime[:BURSt[1]]:TIME[:OFFSet][:SELected]
SETup:PVTime:BURSt2|3|4|5|6:TIME[:OFFSet][:SELected]
|
Function
|
GSM TA
|
This command sets/queries the time offsets (for the specified burst of the multislot configuration) for the power vs time power measurement, (not the mask measurement) in the active (that is the selected) format.
All 12 time offsets are set to on by default. If less than 12 values are sent with this command, the remaining offsets are turned off, see
Power versus Time Measurement Description
. These values are referenced to the occurrence of bit 0 in a normal burst.
The units (S|MS|US|NS) are optional, if no units are specified then units default to S.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
Range: 0 to 12 comma-separated values ranging from: -50 us to 590 us
Note that there is a further restriction on this range to ensure that a valid result is returned when testing a GPRS mobile which supports a multislot configuration with two uplink timeslots. For more details, see
Time Offset Range Restrictions for GPRS and EGPRS Mobiles
.
Resolution: 1 ns
|
|
Query
|
Range: 1 to 12 comma-separated values ranging from: -50 us to 590 us and 9.91E+37 (NAN) if no offsets are specified
Resolution: 1 ns
|
|
*RST Setting
|
Time offsets 1 through 12 are on and set to these values:
|
|
|
Burst 1
-
time offset 1 = -28 us
-
time offset 2 = -18 us
-
time offset 3 = -10 us
-
time offset 4 = 0 us
-
time offset 5 = 321.2 us
-
time offset 6 = 331.2 us
-
time offset 7 = 339.2 us
-
time offset 8 = 349.2 ms
-
time offset 9 = 542.8 us
-
time offset 10 = 552.8 us
-
time offset 11 = 560.8 us
time offset 12 = 570.8 us
|
Burst 2
-
time offset 1 = 0 us
-
time offset 2 = 0 us
-
time offset 3 = 0 us
-
time offset 4 = 0 us
-
time offset 5 = 321.2 us
-
time offset 6 = 331.2 us
-
time offset 7 = 339.2 us
-
time offset 8 = 349.2 us
-
time offset 9 = 542.8 us
-
time offset 10 = 552.8 us
-
time offset 11 = 560.8 us
-
time offset 12 = 570.8 us
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
Revision: A.08 adds Burst 3 and 4
Revision: A.09 adds Burst 5
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
Revision: E.02 adds Burst 3 and 4
Revision: F.01 adds Burst 5
Revision: G.00.00 adds Burst 6
|
|
Programming Example
OUTPUT 714;"SETUP:PVTIME:BURSt2:TIME:OFFSET 0US, 0US, 0US, 0US, 321.2.0US, 331.2US"
! Configures the first six time offset points and turns the remaining six off for burst 2.
! Using the query form of this command would return six time offset values.
|
SETup:PVTime[:BURSt[1]]:TIME:POINts[:SELected]?
SETup:PVTime:BURSt2|3|4|5|6:TIME:POINts[:SELected]?
|
Function
|
GSM TA
|
This command queries the number of the specified burst's Measurement Offset points that are turned on during a power versus time measurement in the active (that is the selected) format.
This command is useful for determining how many time values are returned in a comma-separated list when the
SETup:PVTime[:BURSt[1]]:TIME[:OFFSet][:SELected]
query is sent, and how many power values are returned when the
FETCh:PVTime[:BURSt[1]]:POWer[:ALL][:MAXimum]?
command is sent.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Query
|
Range: 0 to 12
Resolution: 1
|
|
*RST Setting |
12 |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
Revision: A.08 adds Burst 3 and 4
Revision: A.09 adds Burst 5
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
Revision: E.02 adds Burst 3 and 4
Revision: F.01 adds Burst 5
Revision: G.00.00 adds Burst 6
|
SETup:PVTime:CONTinuous[:SELected]
|
Function
|
GSM TA
|
This command sets/queries the trigger state for power versus time measurements in the active (that is the selected) format. See
Measurement States
.
|
|
GPRS TA
|
|
EGPRS TA |
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
Setting |
Range:
-
Single trigger mode = 0 | OFF
-
Continuous trigger mode = 1 | ON
|
|
Query
|
Range: 0 | 1
|
|
*RST Setting |
1 |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:PVTIME:CONTINUOUS OFF"
! Specifies single trigger mode for power versus time measurements.
|
SETup:PVTime:COUNt[:SNUMber]
|
Function
|
GSM TA
|
This command sets/queries the number of power versus time measurements made by the test set. This command sets the count state to ON for this value to take effect.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
Range: 1 to 999
Resolution: 1
|
|
Query
|
Range: 1 to 999
Resolution: 1
|
|
*RST Setting |
10 |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:PVTIME:COUNT:SNUMBER 25"
! Sets the state to on and the multi-measurement count value to 25.
|
SETup:PVTime:COUNt:NUMBer
|
Function
|
GSM TA
|
This command sets/queries the number of Power vs Time measurements made by the test set. The multi-measurement count state must be on.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
Range: 1 to 999
Resolution: 1
|
|
Query
|
Range: 1 to 999
Resolution: 1
|
|
*RST Setting |
10 |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:PVTIME:COUNT:NUMBER 20"
! Sets multi-measurement count value to 20.
|
SETup:PVTime:COUNt:STATe
|
Function
|
GSM TA
|
This command sets/queries the power versus time multi-measurement count state in the active (that is the selected) format.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
Range: 0 | OFF | 1 | ON
|
|
Query
|
Range: 0 | 1
|
|
*RST Setting |
0 | OFF
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:PVTIME:COUNT:STATE ON"
! Sets multi-measurement count state to on.
|
SETup:PVTime:CUSTom1:MASK:LOWer?
SETup:PVTime:CUSTom2:MASK:LOWer?
|
Function
|
GSM TA
|
This command sets/queries the lower limits for the specified custom mask to be used with the Power versus Time measurement.
A total of 32 reference points are available to you when defining a custom mask. All custom masks have a step profile rather than a linearly interpolated profile. Each custom mask has a fixed starting point which is located -50 us relative to the middle of the zero-th symbol (that is, T0). All mask reference points that you specify are end points of one section of the custom mask.
If you use this command without specifying any parameters, the previously defined mask is cleared.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
Range:
0 to 32 comma-separated value pairs containing Time and Relative Power within the following ranges:
-
Time: -50 us to 593 us
-
Relative Power and Absolute Power: -200 to +200 dBc
Resolution:
-
Time: 1 ns
-
Relative Power: 0.1 dB
|
|
Query
|
Range:
0 to 32 comma-separated value pairs containing Time and Relative Power within the following ranges:
-
Time: -50 us to 593 us and 9.91E+37 (NAN) if no offsets are specified
-
Relative Power and Absolute Power: -200 to +200 dBc
Resolution:
-
Time: 1 ns
-
Relative Power: 0.1 dB
|
|
*RST Setting |
ETSI GMSK Mask |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:PVTIME:CUSTOM1:MASK:LOWER 0us, -2, 300us, 3
! Sets the first 2 points of the lower custom mask. All other points are blanked.
|
SETup:PVTime:CUSTom1:MASK:LOWer:POINts?
SETup:PVTime:CUSTom2:MASK:LOWer:POINts?
|
Function
|
GSM TA
|
This query returns the number of reference points for the specified user settable lower mask.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Query
|
Range: 0 to 32
Resolution: 1
|
|
*RST Setting |
0 |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
SETup:PVTime:CUSTom1:MASK:UPPer?
SETup:PVTime:CUSTom2:MASK:UPPer?
|
Function
|
GSM TA
|
This command sets/queries the upper limits for the specified custom mask to be used with the Power versus Time measurement.
A total of 32 reference points are available to you when defining a custom mask. All custom masks have a step profile rather than a linearly interpolated profile. Each custom mask has a fixed starting point which is located -50 us relative to the middle of the zero-th symbol (that is, T0). All mask reference points that you specify are end points of one section of the custom mask.
If you use this command without specifying any parameters, the previously defined mask is cleared.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
Range:
0 to 32 comma-separated value pairs containing Time and Relative Power within the following ranges:
-
Time: -50 us to 593 us
-
Relative Power and Absolute Power: -200 to +200 dBc
Resolution:
-
Time: 1 ns
-
Relative Power: 0.1 dB
|
|
Query
|
Range:
0 to 32 comma-separated value pairs containing Time and Relative Power within the following ranges:
-
Time: -50 us to 593 us and 9.91E+37 (NAN) if no offsets are specified
-
Relative Power and Absolute Power: -200 to +200 dBc
Resolution:
-
Time: 1 ns
-
Relative Power: 0.1 dB
|
|
*RST Setting |
ETSI GMSK Mask |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:PVTIME:CUSTOM1:MASK:UPPER -40us, 50, -20us, 10, 0us, 1, 300us, 2"
! Sets the first 4 points of the upper custom mask. All other points are blanked.
|
SETup:PVTime:CUSTom1:MASK:UPPer:POINts?
SETup:PVTime:CUSTom2:MASK:UPPer:POINts?
|
Function
|
GSM TA
|
This query returns the number of reference points for the specified user settable upper mask.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Query
|
Range: 0 to 32
Resolution: 1
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
SETup:PVTime:ETXPower[:METHod]
|
Function
|
GSM TA
|
This command is not applicable to GSM.
|
|
GPRS TA
|
This command is not applicable to GPRS.
|
|
GSM/GPRS LA
|
This command is not applicable to the GSM/GPRS LA. |
|
EGPRS TA
|
This command allows you to specify how to calculate the Transmit Power (which constitutes the 0dB level in the mask). This command is only available in the 8PSK version of the Power versus Time measurement.
|
|
EGPRS LA
|
|
Setting |
CARRier | BURSt |
|
Query
|
CARR | BURS
|
|
*RST Setting |
CARRier |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.03 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.03 and above
|
SETup:PVTime:GRAPh:POWer:REFerence
|
Function
|
GSM TA
|
This command sets/queries the reference value for the graph. See
Graph Power Reference
for more information
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
Range: STRongest | BURSt1 | BURSt2 | BURSt3 | BURSt4 | BURSt5
|
|
Query
|
Range: STRongest | BURS1 | BURS2 | BURS3 | BURS4 | BURS5
|
|
*RST Setting |
STRongest |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
Revision: A.08 adds Burst 3 and 4
Revision: A.09 adds Burst 5
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
Revision: E.02 adds Burst 3 and 4
Revision: F.01 adds Burst 5 a
|
SETup:PVTime:GRAPh:STATe
|
Function
|
GSM TA
|
This command sets/queries the power versus time graphics state.
Turning the graphics state ON causes the measurement time to increase significantly.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
Range: 0 | OFF | 1 | ON
|
|
Query
|
Range: 0 | 1
|
|
*RST Setting |
0 | OFF
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SET:PVT:GRAP:STAT ON"
! Sets PvT graphic state to on.
|
SETup:PVTime:GRAPh:TIME:REFerence
|
Function
|
GSM TA
|
This command sets/queries the time reference for the graph. See
Graph Power Reference
for more information.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
Range: BURSt1 | BURSt2 | BURSt3 | BURSt4 | BURSt5
|
|
Query
|
Range: BURS1 | BURS2 | BURS3 | BURS4 | BURS5
|
|
*RST Setting |
BURSt1
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
Revision: A.08 adds Burst 3 and 4
Revision: A.09 adds Burst 5
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
Revision: E.02 adds Burst 3 and 4
Revision: F.01 adds Burst 5
|
SETup:PVTime:LIMit:ETSI:PCS
|
Function
|
GSM TA
|
This command sets/queries the mask specification used for the PCS band in the active (that is the selected) format. ETSI define a relaxed mask specification for the PCS band in 3GPP 51.010-1 section 13.3.5(c).
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
NARRow | RELaxed
|
|
Query
|
NARR | REL
|
|
*RST Setting |
NARRow |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:PVTIME:LIMIT:ETSI:PCS REL"
! Selects the relaxed mask specification for power versus time measurements in the PCS band.
|
SETup:PVTime:RANGing[:MODE]
|
Function
|
GSM TA
|
This command sets/queries the ranging mode for the power versus time measurement.
When set to High Linearity Mode (HLINearity), the hardware ranges for measuring the second burst such that the first burst never overranges the hardware by more than 20 dB. This will prevent overshoot sufficiently but it also reduces the dynamic range (since this solution lifts the noise floor). This High Linearity Mode results in less dynamic range.When set to High Dynamic Range Mode (HDynamic), the hardware is ranged when measuring the second burst based on its expected power level. Consequently the burst is optimal with regards to dynamic range but a large overrange (due to the first burst) will effect the amplitude accuracy at the beginning of the useful part of the second burst (This may result in an Overshoot condition).
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
HLINearity | HDYNamic
|
|
Query
|
HLIN | HDYN
|
|
*RST Setting |
HLIN
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETup:PVTime:RANGing:MODE HDYN"
! Selects high dynamic range mode.
|
SETup:PVTime:BSYNc
SETup:PVTime:SYNC
|
Function
|
GSM TA
|
This command sets/queries the burst synchronization mode for power versus time measurements in the active (that is the selected) format. See
Burst Synchronization
for more information.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
MIDamble | AMPLitude | NONE
|
|
Query
|
MID | AMPL | NONE
|
|
*RST Setting |
MID
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:PVTIME:SYNC MIDAMBLE"
! Selects burst synchronization to midamble for GPRS power versus time measurements.
|
SETup:PVTime:TIMeout[:STIMe]
|
Function
|
GSM TA
|
This command sets/queries the timeout value in seconds that is used for power versus time measurements in the active (that is the selected) format. This command also sets the timeout state to on. The units (S|MS) are optional, if no units are specified then units default to S.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
Range: 0.1 to 999 seconds
Resolution: 0.1 seconds
|
|
Query
|
Range: 0.1 to 999 seconds
Resolution: 0.1 seconds
|
|
*RST Setting |
10 seconds |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:PVTIME:TIMEOUT:STIME 4"
! Sets the state to on and the timeout value to 4 seconds.
|
SETup:PVTime:TIMeout:TIME
|
Function
|
GSM TA
|
This command sets/queries the timeout value in seconds that will be used for power versus time measurements in the active (that is the selected) format. The units (S|MS) are optional, if no units are specified then units default to S.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
Range: 0.1 to 999 seconds
Resolution: 0.1 seconds
|
|
Query
|
Range: 0.1 to 999 seconds
Resolution: 0.1 seconds
|
|
*RST Setting |
10 seconds
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:PVTIME:TIMEOUT:TIME 6"
! Sets the timeout value to 6 seconds.
|
SETup:PVTime:TIMeout:STATe
|
Function
|
GSM TA
|
This command sets/queries power versus time timeout state in the active (that is the selected) format.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
Range: 0 | OFF | 1 | ON
|
|
Query
|
Range: 0 | 1
|
|
*RST Setting |
0 | OFF
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:PVTIME:TIMEOUT:STATE ON"
! Sets timeout state to on.
|
SETup:PVTime:TRIGger:DELay
|
Function
|
GSM TA
|
This command selects/queries the trigger delay in seconds for power versus time measurements in the active (that is the selected) format. The units (S|MS|US|NS) are optional, if no units are specified then units default to S.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
Range: -2.31 ms to +2.31 ms
Resolution: 5 significant digits or 100 ns, whichever is greater
|
|
Query
|
Range: -2.31 ms to +2.31 ms
Resolution: 5 significant digits or 100 ns, whichever is greater
|
|
*RST Setting |
0 seconds |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:PVTIME:TRIGGER:DELAY 1.1MS"
! Sets trigger delay value to 1.1 milli-seconds.
|
SETup:PVTime:TRIGger:SOURce
|
Function
|
GSM TA
|
This command selects/queries the trigger source for power versus time measurements in the active (that is the selected) format. See
Triggering of Measurements
.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
AUTO | PROTocol | RISE | IMMediate | EXTernal
|
|
Query
|
AUTO | PROT | RISE | IMM | EXT
|
|
*RST Setting |
AUTO
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:PVTIME:TRIGGER:SOURCE AUTO"
! Sets trigger source to automatic.
|
SETup:PVTime:VIDeo:FILTer:BWIDth
|
Function
|
GSM TA
|
This command selects/queries the bandwidth of the video log filter.
|
|
EGPRS LA
|
|
GSM/GPRS LA
|
|
GPRS TA
|
|
EGPRS TA
|
|
Setting |
VBW_WIDE | VBW_300K | VBW_100K | VBW_30K |
|
Query
|
VBW_WIDE | VBW_300K | VBW_100K | VBW_30K
|
|
*RST Setting |
VBW_WIDE |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.05 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: D.02 and above
|
|
Programming Example
OUTPUT 714;"SETup:PVTime:VIDeo:FILTer:BWIDth VBW_WIDE"
! Do not use video filtering.
|
|
|
top
of page