SETup:TXPower
Last updated: December 3, 2008
GPIB Command Conventions
SETup:TXPower:BURSt:CAPTure
|
Function
|
GSM TA
|
This command sets/queries the Burst Capture Range for TX power measurement. See
Burst Capture Range
|
|
GPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
EGPRS TA
|
|
Setting |
SINGle | ALL
|
|
Query
|
SING | ALL |
|
*RST Setting |
SINGle |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.07 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: E.01 and above
|
|
Programming Example
OUTPUT 714;"SETup:TXPower:BURSt:CAPTure SINGle"
! Sets Burst Capture Range to SINGle.
|
SETup:TXPower:CONTinuous
|
Function
|
GSM TA
|
This command sets/queries the trigger state for TX power measurements.
|
|
GPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
EGPRS TA
|
|
Setting |
Range:
-
Single trigger mode = 0 | OFF
-
Continuous trigger mode = 1 | ON
|
|
Query
|
Range: 0 | 1
|
|
*RST Setting |
0
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETup:TXPower:CONTInuous OFF"
! Specifies single trigger mode for TX power measurements.
|
SETup:TXPower:COUNt[:SNUMber]
|
Function
|
GSM TA
|
This command sets/queries the number of TX power measurements made by the test set. This command sets the count state to ON. See
Multi-measurement Count
|
|
GPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
EGPRS TA
|
|
Setting |
Range: 1 to 999
Resolution: 1
|
|
Query
|
Range: 1 to 999
Resolution: 1
|
|
*RST Setting |
10 |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETup:TXPower:COUNt:SNUMber 99"
! Sets the state to on and the multi-measurement count value to 99.
|
SETup:TXPower:COUNt:NUMBer
|
Function
|
GSM TA
|
This command sets/queries the number of TX power measurements the test set makes in the active (that is the selected) format. The multi-measurement count state must be on.
|
|
GPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
EGPRS TA
|
|
Setting |
Range: 1 to 999
Resolution: 1
|
|
Query
|
Range: 1 to 999
Resolution: 1
|
|
*RST Setting |
10 |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETup:TXPower:COUNt:NUMBer 5"
! Sets the TX Power multi-measurementcount number to 5.
|
SETup:TXPower:COUNt:STATe
|
Function
|
GSM TA
|
This command sets/queries the TX power multi-measurement count state.
|
|
GPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
EGPRS TA
|
|
Setting |
Range: 0 | OFF | 1 | ON
|
|
Query
|
Range: 0 | 1
|
|
*RST Setting |
0
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETup:TXPower:COUNt:STATe ON"
! Sets the multi-measurement count state to on.
|
SETup:TXPower:ECPower:STATe
|
Function
|
GSM TA
|
This command is only applicable when the Burst Capture Range is set to All.
This command sets/queries the Estimated Carrier Power State. See
Estimated Carrier Power
|
|
GPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
EGPRS TA
|
|
Setting |
Range: 0 | OFF | 1 | ON |
|
Query
|
Range: 0 | 1
|
|
*RST Setting |
1
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.07 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: E.01 and above
|
|
Programming Example
OUTPUT 714;"SETup:TXPower:ECPower:STATe ON"
! Sets the Estimated Carrier Power state to on.
|
SETup:TXPower:FRAMe:QUALifier
|
Function
|
GSM TA
|
This command sets/queries the frame qualification for TX power measurements when the operating mode is not Fast Device Tune. See
Frame Qualification
.
|
|
GPRS TA
|
|
GSM/GPRS LA |
|
EGPRS LA
|
|
EGPRS TA
|
|
Setting |
Range: 0 | OFF | 1 | ON
|
|
Query
|
Range: 0 | 1
|
|
*RST Setting |
0 |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.07 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: E.01 and above
|
|
Programming Example
OUTPUT 714;"SETup:TXPower:FRAMe:QUALifier ON"
! Sets TX Power meas Frame Qualification state to on.
|
SETup:TXPower:GFDTune:RSET
|
Function
|
GSM TA
|
This command sets/queries the measurement results of which Uplink Sequence Step are returned when the FETCH GPIB commands other than FETCh:TXPower:TSEQuence and FETCh:TXP:SSTep are used. This parameter is only applicable when the operating mode is set to Fast Device Tune. See
Fast Device Tune Result Set
|
|
GPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
EGPRS TA
|
|
Setting |
Range: 1 to 50
Resolution: 1 |
|
Query
|
Range: 1 to 50
Resolution: 1 |
|
*RST Setting |
1 |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.08 and above, with the required feature license.
|
|
GSM/GPRS/
EGPRS LA
|
Revision: E.02 and above.
|
|
Programming Example
OUTPUT 714;"SETup:TXPower:GFDTune:RSET 10"
! The results of USS 10 will be returned.
|
SETup:TXPower:GFDTune:THReshold
|
Function
|
GSM TA
|
This command sets/queries the threshold for the first RF trigger in the Fast Device Tune operating mode. See
Fast Device Tune Trigger Threshold
|
|
GPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
EGPRS TA
|
|
Setting |
Range: 10 dB to 35 dB
Resolution: 1 dB |
|
Query
|
Range: 10 dB to 35 dB
Resolution: 1 dB |
|
*RST Setting |
35 dB |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.09 and above, with the required feature license.
|
|
GSM/GPRS/
EGPRS LA
|
Revision: F.01 and above.
|
|
Programming Example
OUTPUT 714;"SETup:TXPower:GFDTune:THReshold 10"
! Sets the Trigger Threshold to 10dB in the Fast Device Tune operating mode.
|
SETup:TXPower:RANGe:AUTO
|
Function
|
GSM TA
|
This command is only applicable when the Burst Capture Range is set to All.
This command set/queries whether the instrument ranges the hardware to the highest burst or not. See
Auto Range to Highest Burst
|
|
GPRS TA
|
|
GSM/GPRS LA |
|
EGPRS LA
|
|
EGPRS TA
|
|
Setting |
Range: 0 | OFF | 1 | ON
|
|
Query
|
Range: 0 | 1
|
|
*RST Setting |
0
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.07 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: E.01 and above
|
|
Programming Example
OUTPUT 714;"SETup:TXPower:RANGe:AUTO ON"
! Sets Auto-Ranging state to on.
|
SETup:TXPower:SSTep:FRAMes?
|
Function
|
GSM TA
|
This command queries the number of uplink TDMA frames required in an uplink sequence step. This parameter is only applicable when the operating mode is set to Fast Device Tune. See
Uplink Frames per Step
. |
|
GPRS TA
|
|
GSM/GPRS LA |
|
EGPRS LA
|
|
EGPRS TA
|
|
Query
|
Range: 1 to 100000
Resolution: 1
|
|
*RST Setting |
-1 |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.08 and above, with the required feature license.
|
|
GSM/GPRS/
EGPRS LA
|
Revision: E.02 and above.
|
|
Programming Example
OUTPUT 714;"SETup:TXPower:SSTep FRAMes?
! Queries the uplink frames per sequence step in FDT mode.
|
SETup:TXPower:TIMeout[:STIMe]
|
Function
|
GSM TA
|
This command sets/queries the TX power measurement timeout value. This command also sets the count state to on. The units (S|MS) are optional, if no units are specified then units default to S. See
Measurement Timeout
.
|
|
GPRS TA
|
|
GSM/GPRS LA |
|
EGPRS LA
|
|
EGPRS TA
|
|
Setting |
Range: 0.1 to 999 seconds
Resolution: 0.1 seconds
|
|
Query
|
Range: 0.1 to 999 seconds
Resolution: 0.1 seconds
|
|
*RST Setting |
10 seconds
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETup:TXPower:TIMeout:STIMe 20"
! Sets the state to on and the timeout value to 20 seconds.
|
SETup:TXPower:TIMeout:TIME
|
Function
|
GSM TA
|
This command sets/queries the timeout value in seconds that will be used for TX power measurements in the active (that is the selected) format. The units (S|MS) are optional, if no units are specified then units default to S. See
Measurement Timeout
.
|
|
GPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
EGPRS TA
|
|
Setting |
Range: 0.1 to 999 seconds
Resolution: 0.1 seconds
|
|
Query
|
Range: 0.1 to 999 seconds
Resolution: 0.1 seconds
|
|
*RST Setting |
10 seconds
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETup:TXPower:TIMeout:TIME 20"
! Sets the TX power measurement timeout to 20 seconds.
|
SETup:TXPower:TIMeout:STATe
|
Function
|
GSM TA
|
This command selects/queries TX power measurement timeout state in the active (that is the selected) format. See
Measurement Timeout
.
|
|
GPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
EGPRS TA
|
|
Setting |
Range: 0 | OFF | 1 | ON
|
|
Query
|
Range: 0 | 1
|
|
*RST Setting |
0
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETup:TXPower:TIMeout:STATe 1"
! Turns the TX power timeout state on.
|
SETup:TXPower:TRIGger:DELay
|
Function
|
GSM TA
|
This command sets/queries the trigger delay in seconds for TX power measurements in the active (that is the selected) format. The units (S|MS|US|NS) are optional, if no units are specified then units default to S.
|
|
GPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA |
|
EGPRS TA
|
|
Setting |
Range: -2.31 ms to +2.31 ms
Resolution: 5 significant digits or 100 ns, whichever is greater
|
|
Query
|
Range: -2.31 ms to +2.31 ms
Resolution: 5 significant digits or 100 ns, whichever is greater
|
|
*RST Setting |
0 seconds |
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETup:TXPower:TRIGger:DELay 1.5MS"
! Set trigger delay time to 1.5 milliseconds
|
SETup:TXPower:TRIGger:QUALifier
|
Function
|
GSM TA
|
This command is only applicable when the Burst Capture Range is set to All.
This command sets/queries the trigger qualification for TX power measurements in the active (that is the selected) format. When ON, an automatic trigger re-arm occurs if a measurement is triggered when no valid signal (burst) is present. See
Trigger Qualification Description
.
|
|
GPRS TA
|
|
GSM/GPRS LA |
|
EGPRS LA
|
|
EGPRS TA
|
|
Setting |
Range: 0 | OFF | 1 | ON
|
|
Query
|
Range: 0 | 1
|
|
*RST Setting |
1
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETup:TXPower:TRIGger:QUALifier ON"
! Sets trigger qualifier state to on.
|
SETup:TXPower:TRIGger:SOURce
|
Function
|
GSM TA
|
This command selects/queries the trigger source for TX power measurements in the active (that is the selected) format. See
Triggering of Measurements
.
|
|
GPRS TA
|
|
GSM/GPRS LA
|
|
EGPRS LA
|
|
EGPRS TA
|
|
Setting |
AUTO | PROTocol | RISE | IMMediate | EXTernal
|
|
Query
|
AUTO | PROT | RISE | IMM | EXT
|
|
*RST Setting |
AUTO
|
|
Requirements |
GSM/GPRS/
EGPRS TA
|
Revision: A.01 and above
|
|
GSM/GPRS/
EGPRS LA
|
Revision: C.01 and above
|
|
Programming Example
OUTPUT 714;"SETup:TXPower:TRIGger:SOURce AUTO"
! Sets trigger source to automatic.
|
|
top
of page