CALL:FDDTest

Function

The setting controls the power offset of the P-CPICH transmitted on antenna 2.

Setting

Range: -20 dB to 0 dB

Resolution: 0.01

Increment: 0.1

Query

*RST Setting

Requirements

Lab Application Revision: I.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:ANTenna2:CPIChannel:LEVel:HSDPa -13"
! Sets the FDD Test P-CPICH power offset level to -13 dB.

Function

The setting controls the power offset of the P-CPICH transmitted on antenna 2.

Setting

Query

*RST Setting

Requirements

Test Application Revision: A.20.00 and above, with the required feature license

Lab Application Revision: I.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:ANTenna2:CPIChannel:LEVel:HSPA -13"
! Sets the FDD Test P-CPICH power offset level to -13 dB.

Function

The setting controls the on/off power state of P-CPICH when it is transmitted on antenna 2.

Setting

Range: 1|ON|0|OFF

Query

*RST Setting

Requirements

Lab Application Revision: I.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:ANTenna2:CPIChannel:STATe:HSDPa ON"
! Sets the FDD Test P-CPICH power offset state to on.

Function

The setting controls the on/off power state of P-CPICH when it is transmitted on antenna 2.

Setting

Range: 1|ON|0|OFF

Query

*RST Setting

Requirements

Lab Application Revision: I.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:ANTenna2:CPIChannel:STATe:HSPA ON"
! Sets the FDD Test P-CPICH power offset state to on.

Function

Setting

Query

*RST Setting

Requirements

Lab Application Revision: I.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:ANTenna2:CPIChannel:SLEVel:HSDPa -13"
! Sets the FDD Test P-CPICH power offset Level to -13 dB and turns its state on.

Function

Setting

Query

*RST Setting

Requirements

Lab Application Revision: I.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:ANTenna2:CPIChannel:SLEVel:HSPA -13"
! Sets the FDD Test P-CPICH power offset Level to -13 dB and turns its state on.

Function

The setting specifies whether S-CPICH is transmitted on antenna 2 when Current MIMO Configuration State is Active in FDD Test Operating Mode.

If it is set to On , antenna 1 modulation pattern of S-CPICH will be transmitted on antenna 2. The scrambling code of S-CPICH is UTRA FDD (Cell 1) Primary Scrambling Code .

If it is set to Off , S-CPICH will not be allocated on antenna 2.

Setting

Range: 1|ON|0|OFF

Query

*RST Setting

Requirements

Lab Application Revision: I.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:ANTenna2:CPIChannel:SECondary:CONFig:STATe OFF"
! S-CPICH will not be allocated on antenna 2.

Function

The setting controls the power offset of the S-CPICH transmitted on antenna 2.

Setting

Range: -20 dB to 0 dB

Resolution: 0.01

Increment: 0.1

Query

*RST Setting

Requirements

Test Application Revision: A.20.00 and above, with the required feature license

Lab Application Revision: I.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:ANTenna2:CPIChannel:SECondary:LEVel:HSDPa -13"
! Sets the FDD Test S-CPICH power offset level to -13 dB.

Function

The setting controls the power offset of the S-CPICH transmitted on antenna 2.

Setting

Range: -20 dB to 0 dB

Resolution: 0.01

Increment: 0.1

Query

*RST Setting

Requirements

Test Application Revision: A.20.00 and above, with the required feature license

Lab Application Revision: I.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:ANTenna2:CPIChannel:SECondary:LEVel:HSPA -13"
! Sets the FDD Test S-CPICH power offset level to -13 dB.

Function

The setting controls the on/off power state of S-CPICH when it is transmitted on antenna 2.

Setting

Range: 1|ON|0|OFF

Query

*RST Setting

Requirements

Lab Application Revision: I.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:ANTenna2:CPIChannel:SECondary:STATe:HSDPa ON"
! Sets the FDD Test S-CPICH power offset state to on.

Function

The setting controls the on/off power state of S-CPICH when it is transmitted on antenna 2.

Setting

Range: 1|ON|0|OFF

Query

*RST Setting

Requirements

Lab Application Revision: I.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:ANTenna2:CPIChannel:SECondary:STATe:HSPA ON"
! Sets the FDD Test S-CPICH power offset state to on.

Function

The setting form of this command performs two functions: (1) sets the FDD Test S-CPICH Level (see CALL:FDDTest:ANTenna2:CPIChannel:SECondary:LEVel:HSDPa ) and (2) sets the FDD Test S-CPICH State to on (see CALL:FDDTest:ANTenna2:CPIChannel:SECondary:STATe:HSDPa ).

The query form of this command returns the FDD Test S-CPICH Level .

Setting

Range: -20 dB to 0 dB

Resolution: 0.01dB

Query

*RST Setting

Requirements

Lab Application Revision: I.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:ANTenna2:CPIChannel:SECondary:SLEVel:HSDPa -13"
! Sets the FDD Test S-CPICH power offset Level to -13 dB and turns its state on.

Function

The setting form of this command performs two functions: (1) sets the FDD Test S-CPICH Level (see CALL:FDDTest:ANTenna2:CPIChannel:SECondary:LEVel:HSPA ) and (2) sets the FDD Test S-CPICH State to on (see CALL:FDDTest:ANTenna2:CPIChannel:SECondary:STATe:HSPA ).

The query form of this command returns the FDD Test S-CPICH Level .

Setting

Range: -20 dB to 0 dB

Resolution: 0.01dB

Query

*RST Setting

Requirements

Lab Application Revision: I.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:ANTenna2:CPIChannel:SECondary:SLEVel:HSPA -13"
! Sets the FDD Test S-CPICH power offset Level to -13 dB and turns its state on.

Function

The setting form of this command performs two functions: (1) sets the FDD Test P-CCPCH/SCH Level (see CALL:FDDTest:CCPChannel:PRIMary:LEVel ) and (2) sets the FDD Test P-CCPCH/SCH state to on (see CALL:FDDTest:CCPChannel:PRIMary:STATe ).

The query form of this command returns the FDD Test P-CCPCH/SCH Level .

See FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test or Lab Application Revision: A.01 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CCPChannel:PRIMary -13"
! Sets the FDD Test P-CCPCH/SCH Level to -13 dB and turns its state on.

Function

The setting form of this command performs two functions: (1) sets the HSDPA FDD Test P-CCPCH/SCH Level (see CALL:FDDTest:CCPChannel:PRIMary:LEVel:HSDPa ) and (2) sets the HSDPA FDD Test P-CCPCH/SCH state to on (see CALL:FDDTest:CCPChannel:PRIMary:STATe:HSDPa ).

The query form of this command returns the HSDPA FDD Test P-CCPCH/SCH Level .

See HSDPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CCPChannel:PRIMary:HSDPa -13"
! Sets the HSDPA FDD Test P-CCPCH/SCH Level to -13 dB and turns its state on.

Function

The setting form of this command performs two functions: (1) sets the HSPA FDD Test P-CCPCH/SCH Level (see CALL:FDDTest:CCPChannel:PRIMary:LEVel:HSPA ) and (2) sets the HSPA FDD Test P-CCPCH/SCH state to on (see CALL:FDDTest:CCPChannel:PRIMary:STATe:HSPA ).

The query form of this command returns the HSPA FDD Test P-CCPCH/SCH Level .

See HSPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CCPChannel:PRIMary:HSPA -13"
! Sets the HSPA FDD Test P-CCPCH/SCH Level to -13 dB and turns its state on.

Function

Sets/queries the FDD Test P-CCPCH/SCH Level . See FDD Test Operating Mode .

The FDD Test P-CCPCH/SCH Level can also be set using the CALL:FDDTest:CCPChannel:PRIMary[:SLEVel] command.

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test or Lab Application Revision: A.01 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CCPChannel:PRIMary:LEVel -7"

Function

Sets/queries the HSDPA FDD Test P-CCPCH/SCH Level . See HSDPA in FDD Test Operating Mode .

The HSDPA FDD Test P-CCPCH/SCH Level can also be set using the CALL:FDDTest:CCPChannel:PRIMary[:SLEVel]:HSDPa command.

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CCPChannel:PRIMary:LEVel:HSDPa -7"

Function

Sets/queries the HSPA FDD Test P-CCPCH/SCH Level . See HSPA in FDD Test Operating Mode .

The HSPA FDD Test P-CCPCH/SCH Level can also be set using the CALL:FDDTest:CCPChannel:PRIMary[:SLEVel]:HSPA command.

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CCPChannel:PRIMary:LEVel:HSPA -7"

Function

Sets/queries the FDD Test P-CCPCH/SCH state. See FDD Test Operating Mode .

The FDD Test P-CCPCH/SCH state can also be set using the CALL:FDDTest:CCPChannel:PRIMary[:SLEVel] command.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test or Lab Application Revision: A.01 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CCPChannel:PRIMary:STATe ON" 

Function

Sets/queries the HSDPA FDD Test P-CCPCH/SCH state. See HSDPA in FDD Test Operating Mode .

The HSDPA FDD Test P-CCPCH/SCH state can also be set using the CALL:FDDTest:CCPChannel:PRIMary[:SLEVel] command.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CCPChannel:PRIMary:STATe:HSDPa ON" 

Function

Sets/queries the HSPA FDD Test P-CCPCH/SCH state. See HSPA in FDD Test Operating Mode .

The HSPA FDD Test P-CCPCH/SCH state can also be set using the CALL:FDDTest:CCPChannel:PRIMary[:SLEVel]:HSDPa command.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CCPChannel:PRIMary:STATe:HSPA ON" 

Function

Sets/queries the FDD Test UL CL Power Ctrl Algorithm .

Setting

Range:

• ALG1
• ALG2

Query

*RST Setting

Requirements

Test Application Revision A.07 and above

Lab Application Revision C.02 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CLPControl:UPLink:ALGorithm ALG1" 
! Sets FDD Test UL CL Power Ctrl Algorithm to One.

Function

Sets/queries the FDD Test UL CL Power Ctrl Mode .

Setting

Range:

• ACTive (Active bits)
• DOWN (All Down bits)
• UDOWn (Alternating bits)
• UDOWn10 (10 Up/Down bits)
• UP (All Up bits)

Query

Range: ACT|DOWN|UDOW|UDOW10|UP

*RST Setting

Requirements

Test or Lab Application Revision: A.01 and above

Test Application Revision A.07 and above added ACTive

Lab Application Revision C.02 and above added ACTive

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CLPCONTROL:UPLink:MODE UDOWN" 
!Sets the closed loop power control mode to alternating up, down bits.

Function

Sets/queries the FDD Test UL CL Power Ctrl Stepsize when FDD Test UL CL Power Ctrl Algorithm is set to One (see CALL:FDDTest:CLPControl:UPLink:ALGorithm ).

Setting

Range: 1 to 2 dB

Resolution: 1 dB

Query

*RST Setting

Requirements

Test Application Revision A.07 and above

Lab Application Revision C.02 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CLPControl:UPLink:STEPsize 2 dB" 
! Sets FDD Test UL CL Power Ctrl Stepsize to 2 dB.

Function

Sets/queries Deactivation Type .

Setting

Range:

• IMM (Immediate)
• CFN (Specific CFN)

Query

*RST Setting

Requirements

Lab Application Revision: B.01 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:COMPressed:DACTivation:TYPe CFN"

 
! Sets deactivation type to CFN.

Function

Sets/queries Ending CFN .

Setting

Range: 0 to 255

Resolution: 1

Query

*RST Setting

Requirements

Lab Application Revision: B.01 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:COMPressed:ECFNumber 16"

Function

This command is obsolete. Please use CALL:FDDTest:COMPressed:TGPSequence:ALL:SCFNumber or CALL:FDDTest:COMPressed:TGPSequence([1]|2|3|4):SCFNumber .

Sets/queries Starting CFN for TGPS 1.

Setting

Range: 0 to 255

Resolution: 1

Query

*RST Setting

Requirements

Lab Application Revision: B.01 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:COMPressed:SCFNumber 4"

Function

Sets/queries <num> TG Starting CFN for the first through fourth TGPSs (the first num value sets First TG Starting CFN , the second num value sets Second TG Starting CFN , etc.). You can set TG Starting CFN for an individual TGPS using the CALL:FDDTest:COMPressed:TGPSequence([1]|2|3|4):SCFNumber commands.

Setting

Range: 0 to 255

Resolution: 1

Query

*RST Setting

Requirements

Programming Example

 
OUTPUT 714;"CALL:FDDTest:COMPressed:TGPSequence:ALL:SCFNumber 0,4,12,28"
! Sets First TG Starting CFN to 0, Second TG Starting CFN to 4, 
! Third TG Starting CFN to 12, and Fourth TG Starting CFN to 28.

Function

Sets/queries <num> TG Starting CFN for the first, second, third or fourth TGPS (sending :TGPSequence or :TGPSequence1 sets First TG Starting CFN , sending :TGPSequence2 sets Second TG Starting CFN , etc.). You can set TG Starting CFN for all four TGPSs using the CALL:FDDTest:COMPressed:TGPSequence:ALL:SCFNumber command.

Setting

Range: 0 to 255

Resolution: 1

Query

*RST Setting

• First TGPS: 0
• Second TGPS: 2
• Third TGPS: 6
• Fourth TGPS: 14

Requirements

Programming Example

 
OUTPUT 714;"CALL:FDDTest:COMPressed:TGPSequence3:SCFNumber 12"
! Sets Third TG Starting CFN to 12.

Function

Sets/queries the CPC Activation CFN. This setting controls the specific CFN used by the UE and test set to start the CPC operation immediately after radio frames determined by the "Enabling Delay" parameter has passed.

Setting

Range: 0 to 255

Resolution: 1

Query

*RST Setting

Requirements

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CPC:ACFNumber 0"
! Sets the CPC Activation CFN to 0.

Function

Queries the CPC Configured parameter.

Query

Range: 1|0

*RST Setting

Requirements

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CPC:CONFigured 0"

Function

The setting form of this command performs two functions: (1) sets the FDD Test CPICH Level (see CALL:FDDTest:CPIChannel:LEVel ) and (2) sets the FDD Test CPICH state to on (see CALL:FDDTest:CPIChannel:STATe ).

The query form of this command returns the FDD Test CPICH Level .

See FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test or Lab Application Revision: A.01 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CPIChannel -13"
! Sets the FDD Test CPICH Level to -13 dB and turns its state on.

Function

The setting form of this command performs two functions: (1) sets the HSDPA FDD Test CPICH Level (see CALL:FDDTest:CPIChannel:LEVel:HSDPa ) and (2) sets the HSDPA FDD Test CPICH state to on (see CALL:FDDTest:CPIChannel:STATe:HSDPa ).

The query form of this command returns the HSDPA FDD Test CPICH Level .

See HSDPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CPIChannel:HSDPa -13"
! Sets the HSDPA FDD Test CPICH Level to -13 dB and turns its state on.

Function

The setting form of this command performs two functions: (1) sets the HSPA FDD Test CPICH Level (see CALL:FDDTest:CPIChannel:LEVel:HSPA ) and (2) sets the HSPA FDD Test CPICH state to on (see CALL:FDDTest:CPIChannel:STATe:HSPA ).

The query form of this command returns the HSPA FDD Test CPICH Level .

See HSPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CPIChannel:HSPA -13"
! Sets the HSPA FDD Test CPICH Level to -13 dB and turns its state on.

Function

Sets/queries the FDD Test CPICH Level . See FDD Test Operating Mode .

The FDD Test CPICH Level can also be set using the CALL:FDDTest:CPIChannel[:SLEVel] command.

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test or Lab Application Revision: A.01 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CPIChannel:LEVel -7"

Function

Sets/queries the HSDPA FDD Test CPICH Level . See HSDPA in FDD Test Operating Mode .

The HSDPA FDD Test CPICH Level can also be set using the CALL:FDDTest:CPIChannel[:SLEVel]:HSDPa command.

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CPIChannel:LEVel:HSDPa -7"

Function

Sets/queries the HSPA FDD Test CPICH Level . See HSPA in FDD Test Operating Mode .

The HSPA FDD Test CPICH Level can also be set using the CALL:FDDTest:CPIChannel[:SLEVel]:HSPA command.

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CPIChannel:LEVel:HSPA -7"

Function

Sets/queries the FDD Test CPICH state. See FDD Test Operating Mode .

The FDD Test CPICH state can also be set using the CALL:FDDTest:CPIChannel[:SLEVel] command.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test or Lab Application Revision: A.01 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CPIChannel:STATe ON" 

Function

Sets/queries the HSDPA FDD Test CPICH state. See HSDPA in FDD Test Operating Mode .

The HSDPA FDD Test CPICH state can also be set using the CALL:FDDTest:CPIChannel[:SLEVel]:HSDPa command.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CPIChannel:STATe:HSDPa ON" 

Function

Sets/queries the HSPA FDD Test CPICH state. See HSPA in FDD Test Operating Mode .

The HSPA FDD Test CPICH state can also be set using the CALL:FDDTest:CPIChannel[:SLEVel]:HSPA command.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CPIChannel:STATe:HSPA ON" 

Function

The setting form of this command performs two functions: (1) sets the FDD Test DPCH Level (see CALL:FDDTest:DPCHannel:LEVel ) and (2) sets the FDD Test DPCH state to on (see CALL:FDDTest:DPCHannel:STATe ).

The query form of this command returns the FDD Test DPCH Level .

See FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test or Lab Application Revision: A.01 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:DPCHannel -13"
! Sets the FDD Test DPCH Level to -13 dB and turns its state on.

Function

The setting form of this command performs two functions: (1) sets the HSDPA FDD Test DPCH Level (see CALL:FDDTest:DPCHannel:LEVel:HSDPa ) and (2) sets the HSDPA FDD Test DPCH state to on (see CALL:FDDTest:DPCHannel:STATe:HSDPa ).

The query form of this command returns the HSDPA FDD Test DPCH Level .

See HSDPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:DPCHannel:HSDPa -13"
! Sets the HSDPA FDD Test DPCH Level to -13 dB and turns its state on.

Function

The setting form of this command performs two functions: (1) sets the HSPA FDD Test DPCH Level (see CALL:FDDTest:DPCHannel:LEVel:HSPA ) and (2) sets the HSPA FDD Test DPCH state to on (see CALL:FDDTest:DPCHannel:STATe:HSPA ).

The query form of this command returns the HSPA FDD Test DPCH Level .

See HSPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:DPCHannel:HSPA -13"
! Sets the HSPA FDD Test DPCH Level to -13 dB and turns its state on.

Function

Setting

Range: 0 to 149

Resolution: 1

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above

Lab Application Revision: C.04 and above

Lab Application Revision: D.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:DPCHannel:FOFFset 6"
! Sets DPCH Frame Offset to 6 x 256 chips.

Function

Sets/queries the FDD Test DPCH Level . See FDD Test Operating Mode .

The FDD Test DPCH Level can also be set using the CALL:FDDTest:DPCHannel[:SLEVel] command.

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test or Lab Application Revision: A.01 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:DPCHannel:LEVel -7"

Function

Sets/queries the HSDPA FDD Test DPCH Level . See HSDPA in FDD Test Operating Mode .

The HSDPA FDD Test DPCH Level can also be set using the CALL:FDDTest:DPCHannel[:SLEVel]:HSDPa command.

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:DPCHannel:LEVel:HSDPa -7"

Function

Sets/queries the HSPA FDD Test DPCH Level . See HSPA in FDD Test Operating Mode .

The HSPA FDD Test DPCH Level can also be set using the CALL:FDDTest:DPCHannel[:SLEVel]:HSPA command.

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:DPCHannel:LEVel:HSPA -7"

Function

Sets/queries the FDD Test DPCH state. See FDD Test Operating Mode .

The FDD Test DPCH state can also be set using the CALL:FDDTest:DPCHannel[:SLEVel] command.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test or Lab Application Revision: A.01 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:DPCHannel:STATe ON" 

Function

Sets/queries the HSDPA FDD Test DPCH state. See HSDPA in FDD Test Operating Mode .

The HSDPA FDD Test DPCH state can also be set using the CALL:FDDTest:DPCHannel[:SLEVel]:HSDPa command.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:DPCHannel:STATe:HSDPa ON" 

Function

Sets/queries the HSPA FDD Test DPCH state. See HSPA in FDD Test Operating Mode .

The HSPA FDD Test DPCH state can also be set using the CALL:FDDTest:DPCHannel[:SLEVel]:HSPA command.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:DPCHannel:STATe:HSPA ON" 

Function

The setting form of this command performs two functions: (1) sets the HSPA FDD Test E-AGCH Level (see CALL:FDDTest:EAGChannel:LEVel ) and (2) sets the FDD Test E-AGCH state to on (see CALL:FDDTest:EAGChannel:STATe ).

The query form of this command returns the HSPA FDD Test E-AGCH Level .

See HSPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision: A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:EAGChannel -20"
! Sets the HSPA FDD Test E-AGCH Level
 to -20 dB and turns its state on.

Function

Sets/queries the HSPA FDD Test E-AGCH Level .

The HSPA FDD Test E-AGCH Level can also be set using the CALL:FDDTest:EAGChannel[:SLEVel] command.

See HSPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision: A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:EAGChannel:LEVel -20"

Function

Sets/queries the HSPA FDD Test E-AGCH Level state.

The HSPA FDD Test E-AGCH Level state can also be set using the CALL:FDDTest:EAGChannel[:SLEVel] command.

See HSPA in FDD Test Operating Mode .

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test Application Revision: A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:EAGChannel:STATe ON" 

Function

Sets/queries FDD Test E-DPDCH Max Channel Codes .

Setting

Range: SF64|SF32|SF16|SF8|SF4|TSF4|TSF2

Query

Same as setting

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:EDPDchannel:CCODes:MAX TSF4" 
! Sets FDD Test E-DPDCH Max Channel Codes to 2SF4.

Function

Sets/queries the FDD Test Mode E-DPDCH Max Channelisation Codes (HSPA Only).

This setting is used to inform the test set what value the UE is using for E-DPDCH Max Channelisation Codes while operating in FDD Test Mode with "UTRA FDD RB Test Mode Channel Type" set to"HSPA Only." This value is required to be able to translate the E-TFCI value that the UE transmits on the E-DPCCH to the spreading factor and number of channels used on the E-DPDCH.If "UTRA FDD RB Test Mode Channel Type" is set to "12.2k RMC + HSPA," this parameter is ignored.

Setting

Range: SF64|SF32|SF16|SF8|SF4|TSF4|TSF2|T2T4 (2SF2+2SF4)

Query

Same as setting

*RST Setting

Requirements

Test Application Revision A.13 and above, with the required feature license.

Lab Application Revision: E.01 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:EDPDchannel:CCODes:MAX:HSPA T2T4" 
! Sets FDD Test E-DPDCH Max Channel Codes (HSPA Only) to 2SF2+2SF4.

Function

The setting form of this command performs two functions: (1) sets the HSPA FDD Test E-HICH Level (see CALL:FDDTest:EHIChannel:LEVel ) and (2) sets the HSPA FDD Test E-HICH Level state to on (see CALL:FDDTest:EHIChannel:STATe ).

The query form of this command returns the HSPA FDD Test E-HICH Level .

See HSPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision: A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:EHIChannel -20"
! Sets the HSPA FDD Test E-HICH Level
 to -20 dB and turns its state on.

Function

Sets/queries the HSPA FDD Test E-HICH Level .

The HSPA FDD Test E-HICH Level can also be set using the CALL:FDDTest:EHIChannel[:SLEVel] command.

See HSPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision: A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:EHIChannel:LEVel -20"

Function

Sets/queries the HSPA FDD Test E-HICH Level state.

The HSPA FDD Test E-HICH Level state can also be set using the CALL:FDDTest:EHIChannel[:SLEVel] command.

See HSPA in FDD Test Operating Mode .

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test Application Revision: A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:EHIChannel:STATe ON" 

Function

The setting form of this command performs two functions: (1) sets the HSPA FDD Test E-RGCH Level (see CALL:FDDTest:ERGChannel:LEVel ) and (2) sets the HSPA FDD Test E-RGCH Level state to on (see CALL:FDDTest:ERGChannel:STATe ).

The query form of this command returns the HSPA FDD Test E-RGCH Level .

See HSPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision: A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:ERGChannel -20"
! Sets the HSPA FDD Test E-RGCH Level
 to -20 dB and turns its state on.

Function

Sets/queries the HSPA FDD Test E-RGCH Level .

The HSPA FDD Test E-RGCH Level can also be set using the CALL:FDDTest:ERGChannel[:SLEVel] command.

See HSPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision: A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:ERGChannel:LEVel -20"

Function

Sets/queries the HSPA FDD Test E-RGCH Level state.

The HSPA FDD Test E-RGCH Level state can also be set using the CALL:FDDTest:ERGChannel[:SLEVel] command.

See HSPA in FDD Test Operating Mode .

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test Application Revision: A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:ERGChannel:STATe OFF" 

Function

Sets/queries the E-TFCI Boost setting in the FDD Test Operating Mode. This setting determines the E-TFCI threshold beyond which boosting of E-DPCCH is enabled.

Setting

Range: 0 - 127

Query

Range: 0 - 127

*RST Setting

Requirements

Test Application Revision: A.17.00 and above, with the required feature license.
Lab Application Revision: G.01.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:ETFCi:BOOSt 127" 

Function

Setting

Range: 0 to 9

Resolution: 1

Query

*RST Setting

Requirements

Test Application Revision: A.15 and above

Lab Application Revision: F.01 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:FDPChannel:SLOT:FORMat 0"
! Sets FDD Test Mode F-DPCH Slot Format to 0.

Function

Sets/queries the FDD Test F-DPCH State .

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Lab Application Revision: F.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:FDPChannel:STATe OFF" 

Function

Sets/queries the FDD Test Mode FRC H-Set 8 UE IR Buffer Size.

This Setting controls the FDD Test Mode H-Set 8 UE IR Buffer Size, either 40000 bits or as specified in 25.101v870. If this setting is Standard (STD), the test set will determine the IR buffer size per HARQ process.

Setting

Range: 40000|STD

Query

*RST Setting

Requirements

Test Application Revision A.15 and above.

Lab Application Revision: F.01 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:FRC:HSET8:MS:IREDundancy:BUFFer:SIZE 40000" 
! Sets FDD Test Mode FRC H-Set 8 UE IR Buffer Size to 40000 bits.

Function

Sets/queries the FDD Test Primary Precoding Weight .

Setting

Range: DEF3412101|STATic

Query

*RST Setting

Requirements

Test Application Revision: A.20.00 and above, with the required feature license

Programming Example

 
OUTPUT 714;"CALL:FDDTest:FRC:MIMO:PPWeight:CONFig DEF3412101" 
! Sets the downlink primary precoding weight to be determined as per the specification in the TS34.121-1 section 9.2.4.

Function

Sets/queries the FDD Test "FRC Type" .

Setting

Range:

QAM1|QAM2|QAM3|QAM3A |QAM6|QAM6A|QAM64H8|QAM64H8A|QAM16H10|

QAM16H10A|QPSK1|QPSK2 |QPSK3||QPSK3A|QPSK4|QPSK5|QPSK6|QPSK6A|

QPSKH10|QPSK10A|QPSKH12|HSET9|HSET11

Query

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Test Application Revision A.10.01 and Lab Application Revision D.01.01 added QAM6 and QPSK6.

Lab Application Revision F.00 added QAM64H8, QAM16H10, QPSKH10.

Test Application Revision: A.19.00 and above with the required feature license and Lab Application Revision: H.01.00 and above, added QPSK3A, QAM16H3A, QPSK6A, QAM16H6A, QAM64H8A, QPSK10A, QAM16H10A, QPSK12.

Lab Application Revision I.00.00 added HSET9 and HSET11

Programming Example

 
OUTPUT 714;"CALL:FDDTest:FRC:TYPE QPSK2" 
! Sets FRC Type to H-Set 2 QPSK.

Function

Sets/queries FDD Test Primary H-RNTI (Hex) .

Setting

Range: 0 to FFFF

(1 to 4 characters from the set 0123456789AaBbCcDdEeFf)

Query

Range: "0000" to "FFFF"

(The return string is always 4 characters from the set 0123456789ABCDEF, enclosed by double quotes.)

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HRNTi 'EEEE'" 
! Sets FDD Test Primary H-RNTI (Hex) to EEEE.

Function

Sets/queries FDD Test Alternate H-RNTI (Hex) .

Setting

Range: 0 to FFFF

(1 to 4 characters from the set 0123456789AaBbCcDdEeFf)

Query

Range: "0000" to "FFFF"

(The return string is always 4 characters from the set 0123456789ABCDEF, enclosed by double quotes.)

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HRNTi:ALTernate '2222'" 
! Sets FDD Test Alternate H-RNTI (Hex) to 2222.

Function

Sets/queries FDD Test "HS-SCCH1 Alternate H-RNTI (Hex)" .

Setting

Range: 0 to FFFF

(1 to 4 characters from the set 0123456789AaBbCcDdEeFf)

Query

Range: "0000" to "FFFF"

(The return string is always 4 characters from the set 0123456789ABCDEF, enclosed by double quotes.)

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HRNTi:ALTernate '2222'" 
! Sets FDD Test HS-SCCH 1 Alternate H-RNTI (Hex) to 2222.

Function

Sets/queries FDD Test "HS-SCCH2 Alternate H-RNTI (Hex)" .

Setting

Range: 0 to FFFF

(1 to 4 characters from the set 0123456789AaBbCcDdEeFf)

Query

Range: "0000" to "FFFF"

(The return string is always 4 characters from the set 0123456789ABCDEF, enclosed by double quotes.)

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HRNTi:ALTernate '2222'" 
! Sets FDD Test HS-SCCH 2 Alternate H-RNTI (Hex) to 2222.

Function

Sets/queries FDD Test "HS-SCCH2 Alternate H-RNTI (Hex)" .

Setting

Range: 0 to FFFF

(1 to 4 characters from the set 0123456789AaBbCcDdEeFf)

Query

Range: "0000" to "FFFF"

(The return string is always 4 characters from the set 0123456789ABCDEF, enclosed by double quotes.)

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HRNTi:ALTernate '2222'" 
! Sets FDD Test HS-SCCH 3 Alternate H-RNTI (Hex) to 2222.

Function

Sets/queries FDD Test "HS-SCCH4 Alternate H-RNTI (Hex)" .

Setting

Range: 0 to FFFF

(1 to 4 characters from the set 0123456789AaBbCcDdEeFf)

Query

Range: "0000" to "FFFF"

(The return string is always 4 characters from the set 0123456789ABCDEF, enclosed by double quotes.)

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HRNTi:ALTernate '2222'" 
! Sets FDD Test HS-SCCH 4 Alternate H-RNTI (Hex) to 2222.

Function

Sets/queries the FDD Test Dual Carrier Band Configuration .

This parameter can only be set when Call/Data Status is Idle .

Setting

Range: SBANd|DBANd|UDEFined

Query

*RST Setting

Requirements

Test Application Revision: A.20.00 and above, with the required feature license

Lab Application Revision I.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDPa:MCARrier:BAND:CONFig:TYPE SBANd"
! Sets the FDD Test primary and secondary serving cell DL UARFCN use UARFCNs that are in the single band.

Function

Setting

Range: FRC|UDEFined

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above, with the required feature license

Lab Application Revision: C.04 and above

Lab Application Revision: D.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDSchannel:CONFig UDEFined"
! Sets FDD Test HS-DSCH Configuration Type to User Defined.

Function

Sets/queries FDD Test "HS-DSCH Data Pattern" .

Setting

Range:

• ABITs (Alternating)
• INCRement (Incrementing)
• ONES (All Ones)
• PRBS23 (CCITT PRBS23)
• PRBS20 (CCITT PRBS20)
• PRBS15 (CCITT PRBS15)
• PRBS9 (CCITT PRBS9)
• ZERos (All Zeros)

Query

Range:

• ABIT (Alternating)
• INCR (Incrementing)
• ONES (All Ones)
• PRBS23 (CCITT PRBS23)
• PRBS20 (CCITT PRBS20)
• PRBS15 (CCITT PRBS15)
• PRBS9 (CCITT PRBS9)
• ZER (All Zeros)

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Lab Application Revision: F.00 added PRBS23 and PRBS20

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDSchannel:DATA ONES" 
! Sets FDD Test HS-DSCH Data Pattern to All Ones.

Function

Sets/queries FDD Test "N_cqi_typeA/M_cqi Ratio" .

Setting

Range: R1To2| R2To3|R3To4| |R4To5|R5To6|R6To7|R7To8|R8To9|R9To10|R1To1

Query

*RST Setting

Requirements

Test Application Revision: A.20.00 and above, with the required feature license

Lab Application Revision: I.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDSchannel:MIMO:NMRatio R1To1"
! Sets the N_cqi_typeA/M_cqi ratio on the HS-DPCCH to 1/1 when operating in FDD Test Mode.

Function

Sets/queries FDD Test Static Primary Precoding Weight .

Setting

Range: 0|1|2|3|

Query

*RST Setting

Requirements

Test Application Revision: A.20.00 and above, with the required feature license

Lab Application Revision: I.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDSchannel:MIMO:PPWeight:STATic 2"
! Sets the primary precoding weight applied in the FDD Test Mode to 2.

Function

Sets/queries FDD Test Mode "Number of Transport Blocks" .

Setting

Range: 1 | 2

Query

*RST Setting

Requirements

Test Application Revision: A.20.00 and above, with the required feature license

Lab Application Revision: I.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDSchannel:MIMO:TBLock:COUNt 2"
! Sets the number of transport blocks scheduled on the HS-DSCH to 2 when operating in FDD Test Mode.

Function

Sets/queries FDD Test UE HS-DSCH Category .

This command is only applicable when CALL:FDDTest:HSDSchannel:UDEFined:MS:IREDundancy:BUFFer:ALLocation is set to IMPLicit .

Setting

Range: 1 to 14,17,18,21-24

Resolution: 1

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above, with the required feature license

Lab Application Revision: C.04 and above

Lab Application Revision: D.00 and above

Test Application Revision A.10 and Lab Application Revision D.01 added UE categories 7 and 8

Test Application Revision: A.19.00 and above with the required feature license, added 21-24.
Lab Application Revision: H.01.00 and above, added 21-24.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDSchannel:MS:CATegory 12"
! Sets FDD Test UE HS-DSCH Category to 12.

Function

Sets/queries whether the FDD Test Mode HSDPA/HSPA cell configuration should include DC-HSDPA. If it is set to ON, DC-HSDPA will be configured.

Setting

Range: 1|ON|0|OFF

Query

*RST Setting

Requirements

Test Application Revision: A.19.00 and above, with the required feature license

Lab Application Revision: H.01.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDSchannel:UDEFined:DCHSdpa ON"
! Sets FDDT DC-HSDPA State to ON.

Function

Setting

Range: 1 to 8

Resolution: 1

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above, with the required feature license

Lab Application Revision: C.04 and above

Lab Application Revision: D.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDSchannel:UDEFined:HARQ:PROCess:COUNt 1"
! Sets FDD Test User Defined Number of HARQ Processes to 1.

Function

Setting

Range: 1 to 15

Resolution: 1

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above, with the required feature license

Lab Application Revision: C.04 and above

Lab Application Revision: D.00 and above

Test Application Revision A.10 and Lab Application Revision D.01 expanded range from "1 to 5" to "1 to 10"

Test Application Revision A.15 and Lab Application Revision F.01 expanded range from "1 to 10" to "1 to 15"

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDSchannel:UDEFined:HSPDschannel:COUNt 3"
! Sets FDDT User Defined Number of Active HS-PDSCHs to 3.

Function

Setting

Range: 1 to 3

Resolution: 1

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above, with the required feature license

Lab Application Revision: C.04 and above

Lab Application Revision: D.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDSchannel:UDEFined:ITTI 1"
! Sets FDD Test User Defined Inter-TTI Interval to 1.

Function

Setting

Range: HSPeed | EHSPeed

Query

*RST Setting

Requirements

Lab Application Revision: F.00 and above

Test Application Revision: A.14 and above, with the required feature license

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDSchannel:UDEFined:MAC HSPeed"
! Sets the FDD Test Mode HS-DSCH MAC entity to MAC-hs.

Function

Setting

Range: BIT | OCTet

Query

*RST Setting

Requirements

Lab Application Revision: F.00 and above

Test Application Revision: A.14 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDSchannel:UDEFined:MACEHS:TBSTable:ALIGnment OCTet"
! Sets the FDD Test Mode MAC-ehs HS-DSCH TB size table to octet-aligned.

Function

Sets/queries FDD Test HSDPA MIMO State

This application requires the installation of 8.0 hardware or later.

This setting can not be configured when FDD Test Mode DC-HSDPA State is set to On .

Setting

Range: 1|ON|0|OFF

Query

*RST Setting

Requirements

Test Application Revision: A.20.00 and above, with the required feature license

Lab Application Revision: I.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDSchannel:UDEFined:MIMO:STATe ON"
! Sets the MIMO be configured in the serving cell when operating in FDD Test Mode.

Function

Sets/queries FDD Test Number of HARQ Processes for MIMO

Setting

Range: 12|14|16

Query

*RST Setting

Requirements

Test Application Revision: A.20.00 and above, with the required feature license

Lab Application Revision: I.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDSchannel:UDEFined:MIMO:HARQ:PROCess:COUNt 14"
! Sets the number of HARQ processes that are active in the MAC-ehs layer to 14 when FDD Test Mode HSDPA MIMO State
 is set to On
.

Function

Sets/queries FDD Test "User Defined Modulation Type" .

The setting is for the primary transport block when MIMO is configured.

Setting the modulation type with the value lower than FDD Test "Secondary TB Modulation Type" will post the error message: "FDD call operation rejected; primary transport modulation type must not be lower than secondary transport block modulation type".

Setting

Range: QPSK|QAM16|QAM64

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above, with the required feature license

Lab Application Revision: C.04 and above

Lab Application Revision: D.00 and above

Lab Application Revision: F.00 and Test Application Revision: A.14, added QAM64

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDSchannel:UDEFined:MODulation QAM16"
! Sets FDD Test User Defined Modulation Type to 16QAM.

Function

Sets/queries FDD Test User Defined UE IR Buffer Allocation .

When this command is set to IMPLicit , the UE IR buffer size is determined by the CALL:FDDTest:HSDSchannel:MS:CATegory setting.

When this command is set to EXPLicit , the UE IR buffer size is determined by the CALL:FDDTest:HSDSchannel:UDEFined:MS:IREDundancy:BUFFer:SIZE[:EXPLicit] setting.

Setting

Range: IMPLicit|EXPLicit

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above, with the required feature license

Lab Application Revision: C.04 and above

Lab Application Revision: D.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDSchannel:UDEFined:MS:IREDundancy:BUFFer:ALLocation EXPLicit"
! Sets FDD Test User Defined UE IR Buffer Allocation to Explicit.

Function

Sets/queries FDDT "User Defined Explicit UE IR Buffer Size" .

This command is only applicable when CALL:FDDTest:HSDSchannel:UDEFined:MS:IREDundancy:BUFFer:ALLocation is set to EXPLicit .

Setting

Range: 800, 1600, 2400, 3200, 4000, 4800, 5600, 6400, 7200, 8000, 8800, 9600, 10400, 11200, 12000, 12800, 13600, 14400, 15200, 16000, 17600, 19200, 20800, 22400, 24000, 25600, 27200, 28800, 30400, 32000, 36000, 40000, 44000, 48000, 52000, 56000, 60000, 64000, 68000, 72000, 76000, 80000, 88000, 96000, 104000, 112000, 120000, 128000, 136000, 144000, 152000, 160000, 176000, 192000, 208000, 224000, 240000, 256000, 272000, 288000, 304000

Resolution: 1

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above, with the required feature license

Lab Application Revision: C.04 and above

Lab Application Revision: D.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDSchannel:UDEFined:MS:IREDundancy:BUFFer:SIZE 9600"
! Sets FDDT User Defined Explicit UE IR Buffer Size to 9600.

Function

Sets/queries FDD Test "Secondary TB Modulation Type" and determines the actual transport block size described in Test Mode User Def TBS(Secondary Data Stream) .

Setting the modulation type to 64 QAM when FDD Test "User Defined 64QAM State" is Off will post +237 error message: "FDD call operation rejected; 64QAM must be configured when modulation type is 64QAM".

Setting the modulation type with the value higher than FDD Test "User Defined Modulation Type" will post the error message: "FDD call operation rejected; primary transport modulation type must not be lower than secondary transport block modulation type".

Setting

Range: QAM16|QPSK|QAM64

Query

*RST Setting

Requirements

Test Application Revision: A.20.00 and above, with the required feature license

Lab Application Revision: I.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDSchannel:UDEFined:STBLock:MODulation:TYPE QPSK"
! Sets the secondary transport block modulation type to QPSK when FDD Test Mode HSDPA MIMO State
 is set to On
.

Function

Sets/queries FDD Test "Secondary TB Size Index" .

Setting

Range: 0 to 62

Query

*RST Setting

Requirements

Test Application Revision: A.20.00 and above, with the required feature license

Lab Application Revision: I.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDSchannel:UDEFined:STBSize:INDex 48"
! Sets the secondary transport block size index to 48 when FDD Test Mode HSDPA MIMO State
 is set to On
.

Function

Sets/queries FDDT "User Defined Transport Block Size Index" .

You can query the transport block size using the CALL:STATus:HSDSchannel:TBSize? query.

Setting

Range: 0 to 62

Resolution: 1

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above, with the required feature license

Lab Application Revision: C.04 and above

Lab Application Revision: D.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDSchannel:UDEFined:TBSize:INDex 48"
! Sets FDDT User Defined Transport Block Size Index to 48.

Function

Sets/queries FDD Test "User Defined 64QAM State" . This parameter is used when CALL:FDDTest:HSDSchannel:UDEFined:MAC is set to EHSPeed (MAC-ehs).

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test or Lab Application Revision: F.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSDSchannel:UDEFined:QAM64:STATe OFF" 

Function

The setting form of this command performs two functions: (1) sets the HSDPA FDD Test HS-PDSCHs Level (Sum) (see CALL:FDDTest:HSPDschannel:LEVel ) and (2) sets the HSDPA FDD Test HS-PDSCHs Level (Sum) state to on (see CALL:FDDTest:HSPDschannel:STATe ).

The query form of this command returns the HSDPA FDD Test HS-PDSCHs Level (Sum) .

See HSDPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSPDschannel -4"
! Sets the FDD Test HS-PDSCHs Level (Sum)
 to -4 dB and turns its state on.

Function

The setting form of this command performs two functions: (1) sets the HSPA FDD Test HS-PDSCHs Level (Sum) (see CALL:FDDTest:HSPDschannel:LEVel:HSPA ) and (2) sets the HSPA FDD Test HS-PDSCHs Level (Sum) state to on (see CALL:FDDTest:HSPDschannel:STATe:HSPA ).

The query form of this command returns the HSPA FDD Test HS-PDSCHs Level (Sum) .

See HSPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSPDschannel:HSPA -4"
! Sets the HSPA FDD Test HS-PDSCHs Level (Sum)
 to -4 dB and turns its state on.

Function

THIS COMMAND IS OBSOLETE. Please use CALL:FDDTest:HSPDschannel:CCODe:CODE .

Sets/queries FDD Test First HS-PDSCH Channelization Code .

Setting

Range: CODE5|CODE6|CODE7|CODE8|CODE9|CODE10|CODE11|CODE12|CODE13|CODE14

Query

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Test Application Revision A.10.01 and Lab Application Revision D.01.01 added CODE5 and CODE6.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSPDschannel:CCODe CODE8" 
! Sets FDD Test First HS-PDSCH Channelization Code to 8.

Function

Sets/queries FDD Test First HS-PDSCH Channelization Code .

Setting

Range: 1 to 15

Query

*RST Setting

Requirements

Lab Application Revision: F.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSPDschannel:CCODe:CODE 7" 
! Sets FDD Test First HS-PDSCH Channelization Code to 7.

Function

Sets/queries the HSDPA FDD Test HS-PDSCHs Level (Sum) . See HSDPA in FDD Test Operating Mode .

The HSDPA FDD Test HS-PDSCHs Level (Sum) can also be set using the CALL:FDDTest:HSPDschannel[:SLEVel] command.

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSPDschannel:LEVel -4"

Function

Sets/queries the HSPA FDD Test HS-PDSCHs Level (Sum) . See HSPA in FDD Test Operating Mode .

The HSPA FDD Test HS-PDSCHs Level (Sum) can also be set using the CALL:FDDTest:HSPDschannel[:SLEVel]:HSPA command.

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSPDschannel:LEVel:HSPA -4"

Function

Sets/queries the HSDPA FDD Test HS-PDSCHs Level (Sum) state. See HSDPA in FDD Test Operating Mode .

The HSDPA FDD Test HS-PDSCHs Level (Sum) state can also be set using the CALL:FDDTest:HSPDschannel[:SLEVel] command.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSPDschannel:STATe ON" 

Function

Sets/queries the HSPA FDD Test HS-PDSCHs Level (Sum) state. See HSPA in FDD Test Operating Mode .

The HSPA FDD Test HS-PDSCHs Level (Sum) state can also be set using the CALL:FDDTest:HSPDschannel[:SLEVel]:HSPA command.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSPDschannel:STATe:HSPA ON" 

Function

The setting form of this command performs two functions: (1) sets the FDD Test HS-SCCH 1 Level (see CALL:FDDTest:HSSCchannel[1]:LEVel ) and (2) sets the FDD Test HS-SCCH 1 Level state to on (see CALL:FDDTest:HSSCchannel[1]:STATe ).

The query form of this command returns the FDD Test HS-SCCH 1 Level .

See HSDPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel -11"
! Sets the FDD Test HS-SCCH 1 Level

 to -11 dB and turns its state on.

Function

The setting form of this command performs two functions: (1) sets the HSPA FDD Test HS-SCCH 1 Level (see CALL:FDDTest:HSSCchannel[1]:LEVel:HSPA ) and (2) sets the HSPA FDD Test HS-SCCH 1 Level state to on (see CALL:FDDTest:HSSCchannel[1]:STATe:HSPA ).

The query form of this command returns the HSPA FDD Test HS-SCCH 1 Level .

See HSPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel:HSPA -11"
! Sets the HSPA FDD Test HS-SCCH 1 Level

 to -11 dB and turns its state on.

Function

Sets/queries the FDD Test Mode HSDPA/HSPA HS-SCCH 1 Channel Configuration State.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Lab Application Revision: F.00 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel:CONFig:STATe ON" 

Function

Sets/queries the FDD Test HS-SCCH 1 Level . See HSDPA in FDD Test Operating Mode .

The FDD Test HS-SCCH 1 Level can also be set using the CALL:FDDTest:HSSCchannel[1][:SLEVel] command.

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel:LEVel -11"

Function

Sets/queries the HSPA FDD Test HS-SCCH 1 Level . See HSPA in FDD Test Operating Mode .

The HSPA FDD Test HS-SCCH 1 Level can also be set using the CALL:FDDTest:HSSCchannel[1][:SLEVel]:HSPA command.

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel:LEVel:HSPA -11"

Function

Sets/queries the FDD Test HS-SCCH 1 Level state. See HSDPA in FDD Test Operating Mode .

The FDD Test HS-SCCH 1 Level state can also be set using the CALL:FDDTest:HSSCchannel[1][:SLEVel] command.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel:STATe ON" 

Function

Sets/queries the HSPA FDD Test HS-SCCH 1 Level state. See HSPA in FDD Test Operating Mode .

The HSPA FDD Test HS-SCCH 1 Level state can also be set using the CALL:FDDTest:HSSCchannel[1][:SLEVel]:HSPA command.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel:STATe:HSPA ON" 

Function

The setting form of this command performs two functions: (1) sets the FDD Test HS-SCCH 2 Level (see CALL:FDDTest:HSSCchannel2:LEVel ) and (2) sets the FDD Test HS-SCCH 2 Level state to on (see CALL:FDDTest:HSSCchannel2:STATe ).

The query form of this command returns the FDD Test HS-SCCH 2 Level .

See HSDPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel2 -11"
! Sets the FDD Test HS-SCCH 2 Level

 to -11 dB and turns its state on.

Function

The setting form of this command performs two functions: (1) sets the HSPA FDD Test HS-SCCH 2 Level (see CALL:FDDTest:HSSCchannel2:LEVel:HSPA ) and (2) sets the HSPA FDD Test HS-SCCH 2 Level state to on (see CALL:FDDTest:HSSCchannel2:STATe:HSPA ).

The query form of this command returns the HSPA FDD Test HS-SCCH 2 Level .

See HSPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel2:HSPA -11"
! Sets the HSPA FDD Test HS-SCCH 2 Level

 to -11 dB and turns its state on.

Function

Sets/queries the FDD Test Mode HSDPA/HSPA HS-SCCH 2 Channel Configuration State.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Lab Application Revision: F.00 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel2:CONFig:STATe ON" 

Function

Sets/queries the FDD Test HS-SCCH 2 Level . See HSDPA in FDD Test Operating Mode .

The FDD Test HS-SCCH 2 Level can also be set using the CALL:FDDTest:HSSCchannel2[:SLEVel] command.

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel2:LEVel -11"

Function

Sets/queries the HSPA FDD Test HS-SCCH 2 Level . See HSPA in FDD Test Operating Mode .

The HSPA FDD Test HS-SCCH 2 Level can also be set using the CALL:FDDTest:HSSCchannel2[:SLEVel]:HSPA command.

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel2:LEVel:HSPA -11"

Function

Sets/queries the FDD Test HS-SCCH 2 Level state. See HSDPA in FDD Test Operating Mode .

The FDD Test HS-SCCH 2 Level state can also be set using the CALL:FDDTest:HSSCchannel2[:SLEVel] command.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel2:STATe ON" 

Function

Sets/queries the HSPA FDD Test HS-SCCH 2 Level state. See HSPA in FDD Test Operating Mode .

The HSPA FDD Test HS-SCCH 2 Level state can also be set using the CALL:FDDTest:HSSCchannel2[:SLEVel]:HSPA command.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel2:STATe:HSPA ON" 

Function

The setting form of this command performs two functions: (1) sets the FDD Test HS-SCCH 3 Level (see CALL:FDDTest:HSSCchannel3:LEVel ) and (2) sets the FDD Test HS-SCCH 3 Level state to on (see CALL:FDDTest:HSSCchannel3:STATe ).

The query form of this command returns the FDD Test HS-SCCH 3 Level .

See HSDPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel3 -11"
! Sets the FDD Test HS-SCCH 3 Level

 to -11 dB and turns its state on.

Function

The setting form of this command performs two functions: (1) sets the HSPA FDD Test HS-SCCH 3 Level (see CALL:FDDTest:HSSCchannel3:LEVel:HSPA ) and (2) sets the HSPA FDD Test HS-SCCH 3 Level state to on (see CALL:FDDTest:HSSCchannel3:STATe:HSPA ).

The query form of this command returns the HSPA FDD Test HS-SCCH 3 Level .

See HSPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel3:HSPA -11"
! Sets the HSPA FDD Test HS-SCCH 3 Level

 to -11 dB and turns its state on.

Function

Sets/queries the FDD Test Mode HSDPA/HSPA HS-SCCH 3 Channel Configuration State.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Lab Application Revision: F.00 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel3:CONFig:STATe ON" 

Function

Sets/queries the FDD Test HS-SCCH 3 Level . See HSDPA in FDD Test Operating Mode .

The FDD Test HS-SCCH 3 Level can also be set using the CALL:FDDTest:HSSCchannel3[:SLEVel] command.

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel3:LEVel -11"

Function

Sets/queries the HSPA FDD Test HS-SCCH 3 Level . See HSPA in FDD Test Operating Mode .

The HSPA FDD Test HS-SCCH 3 Level can also be set using the CALL:FDDTest:HSSCchannel3[:SLEVel]:HSPA command.

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel3:LEVel:HSPA -11"

Function

Sets/queries the FDD Test HS-SCCH 3 Level state. See HSDPA in FDD Test Operating Mode .

The FDD Test HS-SCCH 3 Level state can also be set using the CALL:FDDTest:HSSCchannel3[:SLEVel] command.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel3:STATe ON" 

Function

Sets/queries the HSPA FDD Test HS-SCCH 3 Level state. See HSPA in FDD Test Operating Mode .

The HSPA FDD Test HS-SCCH 3 Level state can also be set using the CALL:FDDTest:HSSCchannel3[:SLEVel]:HSPA command.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel3:STATe:HSPA ON" 

Function

The setting form of this command performs two functions: (1) sets the FDD Test HS-SCCH 4 Level (see CALL:FDDTest:HSSCchannel4:LEVel ) and (2) sets the FDD Test HS-SCCH 4 Level state to on (see CALL:FDDTest:HSSCchannel4:STATe ).

The query form of this command returns the FDD Test HS-SCCH 4 Level .

See HSDPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel4 -11"
! Sets the FDD Test HS-SCCH 4 Level

 to -11 dB and turns its state on.

Function

The setting form of this command performs two functions: (1) sets the HSPA FDD Test HS-SCCH 4 Level (see CALL:FDDTest:HSSCchannel4:LEVel:HSPA ) and (2) sets the HSPA FDD Test HS-SCCH 4 Level state to on (see CALL:FDDTest:HSSCchannel4:STATe:HSPA ).

The query form of this command returns the HSPA FDD Test HS-SCCH 4 Level .

See HSPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel4:HSPA -11"
! Sets the HSPA FDD Test HS-SCCH 4 Level

 to -11 dB and turns its state on.

Function

Sets/queries the FDD Test Mode HSDPA/HSPA HS-SCCH 4 Channel Configuration State.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Lab Application Revision: F.00 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel4:CONFig:STATe ON" 

Function

Sets/queries the FDD Test HS-SCCH 4 Level . See HSDPA in FDD Test Operating Mode .

The FDD Test HS-SCCH 4 Level can also be set using the CALL:FDDTest:HSSCchannel4[:SLEVel] command.

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel4:LEVel -11"

Function

Sets/queries the HSPA FDD Test HS-SCCH 4 Level . See HSPA in FDD Test Operating Mode .

The HSPA FDD Test HS-SCCH 4 Level can also be set using the CALL:FDDTest:HSSCchannel4[:SLEVel]:HSPA command.

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel4:LEVel:HSPA -11"

Function

Sets/queries the FDD Test HS-SCCH 4 Level state. See HSDPA in FDD Test Operating Mode .

The FDD Test HS-SCCH 4 Level state can also be set using the CALL:FDDTest:HSSCchannel4[:SLEVel] command.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel4:STATe ON" 

Function

Sets/queries the HSPA FDD Test HS-SCCH 4 Level state. See HSPA in FDD Test Operating Mode .

The HSPA FDD Test HS-SCCH 4 Level state can also be set using the CALL:FDDTest:HSSCchannel4[:SLEVel]:HSPA command.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Test Application Revision A.12 and above, with the required feature license.

Lab Application Revision: E.00.16 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:HSSCchannel4:STATe:HSPA ON" 

Function

Sets/queries the MAC-hs Header .

Setting

Range: PRESent|DATA

Query

Range: PRES|DATA

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:MACHs:HEADer DATA"
! Sets the MAC-hs Header to Used for Data.

Function

Sets/queries the FDD Test Number of Transmissions .

Setting

Range: 1 to 8

Query

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:MACHs:NTRans 2"
! Sets the FDD Test Number of Transmissions to 2.

Function

Sets/queries the FDD Test RV Sequence .

Note: The number of RV parameters in the sequence that are used is determined by the FDD Test Number of Transmissions setting (see CALL:FDDTest:MACHs:NTRans ). The RV parameters at the end of the list are not used if FDD Test Number of Transmissions is less than 8.

Setting

Range: Comma separated list of 1 to 8 characters from the set 01234567.

Query

Range: Comma separated list of 8 characters from the set 01234567, enclosed by double quotes (if you enter fewer than 8 characters, the query result will fill the remaining characters with zeros).

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:MACHs:RVSequence '0,2,7,4,3,1'"
! Sets the FDD Test RV Sequence to 0,2,7,4,3,1,0,0.

Function

Sets/queries the FDD Test statDTX Reception Behavior .

Setting

Range: ACK|NACK|SDTX

Query

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:MACHs:SDTX:RBEHavior ACK"
! Sets the FDD Test statDTX Reception Behavior to Handle as ACK.

Function

Sets/queries the MAC-hs Transmit Window Size . This setting is only applicable if CALL:FDDTest:MACHs:HEADer is set to Present .

Setting

Range: PDU4|PDU6|PDU8|PDU12|PDU16|PDU24|PDU32

Query

*RST Setting

Requirements

Test Application Revision A.08 and above, with the required feature license.

Lab Application Revision: C.03 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:MACHs:WSIZe:TRANsmit PDU12"
! Sets the MAC-hs Transmit Window Size to 12.

Function

Sets/queries the FDD Test "statDTX Reception Behavior" .

Setting

Range: PASack|PNSNack|PASNack|PNSack|PSSSdtx

Query

*RST Setting

Requirements

Test Application Revision: A.20.00 and above, with the required feature license

Lab Application Revision: I.00.00 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:MACEHS:DTBLocks:SDTX:RBEHavior PSSSdtx"
! Sets the test set respond to a statDTX from the UE when two transport blocks were scheduled as statDTX/statDTX when operating in FDD Test Mode.

Function

Sets/queries the FDD Test "RV Sequence for MIMO Primary Transport Block" .

Setting

Range: Comma separated list of 1 to 8 characters from the set 01234567, each entry being an integer of 0 to 3.

Query

*RST Setting

Requirements

Test Application Revision: A.20.00 and above, with the required feature license

Lab Application Revision: I.00.00 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:MACEHS:PTBLock:RVSequence 0,3,2,1,0,0,0,0"
! Sets the Redundancy Version Sequence used for each transmission of a particlular primary transport block to 0,3,2,1,0,0,0,0 when operating in FDD Test Mode.

Function

Sets/queries the FDD Test "RV Sequence for MIMO Secondary Transport Block" .

Setting

Range: Comma separated list of 1 to 8 characters from the set 01234567, each entry being an integer of 0 to 3.

Query

*RST Setting

Requirements

Test Application Revision: A.20.00 and above, with the required feature license

Lab Application Revision: I.00.00 and above.

Programming Example

 
OUTPUT 714;"CALL:FDDTest:MACEHS:STBLock:RVSequence 0,3,2,1,0,0,0,0"
! Sets the Redundancy Version Sequence used for each transmission of a particlular secondary transport block to 0,3,2,1,0,0,0,0 when operating in FDD Test Mode.

Function

Sets/queries the FDD Test HSDPA/HSPA OCNS 1 to 6 Channel Configuration States.

Setting

Query

Range: 0|1

*RST Setting

Lab Application Revision: F.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:CONFig:STATe:HSDPa 1, 1, 1, 1, 1, 1" 

Function

Sets/queries the FDD Test HSDPA/HSPA orthogonal channel noise simulator (OCNS) 1 to 6 Power Offsets (raletive levels).

Query

Range: 0 to -20 dB, 9.91 E+37

Resolution: 0.01 dB

*RST Setting

Requirements

Lab Application Revision: F.00 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:OCNSource:POFFset:HSDPa 0, 0, 0, 0, 0, 0" 

Function

The setting form of this command performs two functions: (1) sets the FDD Test PICH Level (see CALL:FDDTest:PICHannel:LEVel ) and (2) sets the FDD Test PICH state to on (see CALL:FDDTest:PICHannel:STATe ).

The query form of this command returns the FDD Test PICH Level .

See FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting

Requirements

Test or Lab Application Revision: A.01 and above

Programming Example

 
OUTPUT 714;"CALL:FDDTest:PICHannel -13"
! Sets the FDD Test PICH Level to -13 dB and turns its state on.

Function

The setting form of this command performs two functions: (1) sets the HSDPA FDD Test PICH Level (see CALL:FDDTest:PICHannel:LEVel:HSDPa ) and (2) sets the HSDPA FDD Test PICH state to on (see CALL:FDDTest:PICHannel:STATe:HSDPa ).

The query form of this command returns the HSDPA FDD Test PICH Level .

See HSDPA in FDD Test Operating Mode .

Setting

Range: -20.00 dB to 0 dB, 9.91 E+37

Resolution: 0.01

Query

*RST Setting