CALL:HSUPa

Function

Sets/queries the BetaEd Gain E-AGCH Table Selection setting. This setting determines which table in the 3GPP standard 25.212 v7b0 the UE will use to interpret the absolute grant value indices signalled on E-AGCH. 0 means that UE uses Mapping of Absolute Grant Value Table 16B, whereas 1 indicates that the reference table is the Alternative Mapping of Absolute Grant Value Table 16B.1.

This setting is only applicable when the CALL:HSUPa:EDCHannel:QAM16[:STATe] is set to ON.

This setting can only be changed when the connection status is idle.

Setting

Range: 0 | 1

Query

*RST Setting

Requirements

Test Application Revision: A.17.00 and above
Lab Application Revision: G.01.00 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:BEDGain:EAGChannel:TSELection 1" 
! Sets the BetaEd Gain E-AGCH Table Selection to 1.

Function

Sets/queries the E-DCH Minimum Set E-TFCI (10ms TTI) .

This setting can only be changed when the connection status is idle.

Setting

Range: 0 to 127

Resolution: 1

Query

*RST Setting

9

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:EDCHannel:ETFCi:MSET 9" 
! Sets the E-DCH Minimum Set E-TFCI to 9.

Function

Sets/queries the E-DCH Minimum Set E-TFCI (2ms TTI) .

This setting can only be changed when the connection status is idle.

Setting

Range: 0 to 127

Resolution: 1

Query

*RST Setting

10

Requirements

Test Application Revision: A.13 and above

Lab Application Revision: E.01 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:EDCHannel:ETFCi:MSET:MS2 10" 
! Sets the E-DCH Minimum Set E-TFCI (2ms TTI) to 10.

Function

Sets/queries the E-DCH Minimum Set E-TFCI Information State .

Setting

Range: 1|ON|0|OFF

Query

*RST Setting

1 (ON)

Requirements

Test Application Revision: A.13 and above

Lab Application Revision: E.01 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:EDCHannel:ETFCi:MSET:STATe ON" 
! Sets the E-DCH Minimum Set E-TFCI Information State to On.

Function

Sets/queries the E-DCH TTI .

Setting

Range: MS10 (10 ms TTI)|MS2 (2 ms TTI)

Query

*RST Setting

MS10

Requirements

Test Application Revision: A.13 and above

Lab Application Revision: E.01 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:EDCHannel:TTI MS10" 
! Sets the HSUPA TTI mode to 10ms TTI.

Function

Sets/queries the E-DCH 16QAM State . This setting determines whether the test set signals the UE to operate in UL 16QAM mode for E-DCH.

This setting is only applicable when the CALL:HSUPa:EDCHannel:TTI is set to MS10.

Setting

Range: 1|ON|0|OFF

Query

*RST Setting

Requirements

Test Application Revision: A.17.00 and above, with the required feature license.
Lab Application Revision: G.01.00 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:EDCHannel:QAM16 OFF" 
! Sets the E-DCH 16QAM State to Off.

Function

Sets/queries the E-DPCCH/DPCCH Power Offset (DeltaE-DPCCH) .

This setting can only be changed when the connection status is idle.

Setting

Range: 0 to 8

Resolution: 1

Query

*RST Setting

0

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:EDPCchannel:POFFset 0" 
! Sets E-DPCCH/DPCCH Power Offset (DeltaE-DPCCH) to 0.

Function

Sets/queries the E-DPDCH Power Calculation Formula setting. This setting determines what formula the UE uses to calculate the E-DPDCH power.

This setting can only be changed when the connection status is idle.

Setting

Range: EXTRapolation | INTerpolation

Query

Range: EXTR | INT

*RST Setting

Requirements

Test Application Revision: A.17.00 and above, with the required feature license.
Lab Application Revision: G.01.00 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:EDPDchannel:PCFormula EXTRapolation" 
! Sets the E-DPDCH Power Calculation Formula to EXTRapolation.

Function

Sets/queries the Primary E-RNTI (Hex) .

This setting can only be changed when the connection status is idle.

Setting

Range: 0 to FFFF (1 to 4 characters from the set 0123456789AaBbCcDdEeFf)

Query

Range: "0000" to "FFFF" (The return string is always 4 characters from the set 0123456789AaBbCcDdEeFf, enclosed by double quotes.)

*RST Setting

"AAAA"

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:ERNTi 'AAAA'" 
! Sets the Primary E-RNTI (Hex) to AAAA.

Function

Sets/queries the Alternate E-RNTI (Hex).

This setting can only be changed when the connection status is idle.

Setting

Range: 0 to FFFF (1 to 4 characters from the set 0123456789AaBbCcDdEeFf)

Query

Range: "0000" to "FFFF" (The return string is always 4 characters from the set 0123456789AaBbCcDdEeFf, enclosed by double quotes.)

*RST Setting

"5555"

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:ERNTi:ALTernate '5555'" 
! Sets the Alternate E-RNTI (Hex) to 5555.

Function

Sets/queries the E-TFCI Boost setting. When CALL:HSUPa:ETFCi:BOOSt:INFormation[:STate] is set to On, this setting determines the E-TFCI threshold beyond which boosting of E-DPCCH is enabled.

This setting can only be changed when the connection status is idle.

Setting

Range: 0 to 127

Query

*RST Setting

Requirements

Test Application Revision: A.17.00 and above
Lab Application Revision: G.01.00 and above

Programming Example

 
OUTPUT 714;" CALL:HSUPa:ETFCi:BOOSt 127" 
! Sets the E-TFCI Boost to 127.

Function

Sets/queries the DeltaT2TP setting. When CALL:HSUPa:ETFCi:BOOSt:INFormation[:STate] is set to On and CALL:HSUPa:ETFCi:BOOSt[:VALue] is set to a value other than 127, this setting determines the Delta T2TP value that would be signalled to the UE. The power offset values (in dB) for each signalled value are defined in 3GPP 25.213 v770 Table 1B.0.

This setting can only be changed when the connection status is idle.

Setting

Range: 0 to 6

Query

*RST Setting

Requirements

Test Application Revision: A.17.00 and above
Lab Application Revision: G.01.00 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:ETFCi:BOOSt:DT2Tp 2" 
! Sets the DeltaT2TP
 to 2.

Function

Sets/queries the E-TFC Boost Info State setting. This setting determines whether the test set enables the boosting of E-DPCCH.

This setting can only be changed when the connection status is idle.

Setting

1|ON|0|OFF

Query

*RST Setting

Requirements

Test Application Revision: A.17.00 and above
Lab Application Revision: G.01.00 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:ETFCi:BOOSt:INFormation Off" 
! Sets the E-TFC Boost Info State to Off.

Function

Sets/queries the Predefined Reference E-TFCI Power Offsets .

Setting

Range: DEF3410801|DEF3410802|DEF3412101|DEF3412102|DEF3412103|DEF3412104

Query

*RST Setting

DEF3410802

Requirements

Test Application Revision: A.12 and above, with the required feature license
Lab Application Revision: E.00.16 and above
Lab Application Revision: G.00.09 and above, added DEF3412103
Lab Application Revision: G.01.00 and above, added DEF3412104

Programming Example

 
OUTPUT 714;"CALL:HSUPa:ETFCi:POFFsets:REFerence DEF3410802" 
! Sets the Reference E-TFCI Power Offsets to match those in the Definition 34108-02.

Function

Sets/queries the Reference E-TFCI Power Offset Control .

Setting

PDEFined | MANual

Query

*RST Setting

PDEFined

Requirements

Lab Application Revision: E.01 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:ETFCi:POFFsets:REFerence:CONTrol PDEFined" 
! Sets the Reference E-TFC Configuration to Pre-defined.

Function

Sets/queries the Reference E-TFCI.

Each entry in this list defines the Reference E-TFCI as part of Reference E-TFCIs IE that is signaled to UE at call setup. Whether the Reference E-TFCI is actually present in the RRC message is controlled by the "Reference E-TFCI 1 to 8 States" setting.The valid range for each entry in this list depends on the HSUPA TTI mode and E-DCH TB size table (3GPP TS 25.321 Annex B) in use (See Table below).

The default value comes from 3GPP TS 34.108 s9.2.

Setting

Range: 8 comma separated values (see table below for valid ranges))

Resolution: 1

Query

*RST Setting

11,0,0,0,0,0,0,0

Requirements

Lab Application Revision: E.01 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:ETFCi:POFFsets:REFerence:MANual:INDex 11,0,0,0,0,0,0,0" 
! Sets Reference E-TFCI to 11,0,0,0,0,0,0,0.

2ms TTI

0

0 to 127

1

0 to 125

10ms TTI

0

0 to 127

0 to 120

Function

Sets/queries the Reference E-TFCI Power Offset.

Each entry the in this list defines the Reference E-TFCI PO that is part of Reference E-TFCIs IE signaled to UE at call setup. Whether the Reference E-TFCI PO is actually present in the RRC message is controlled by the "Reference E-TFCI 1 to 8 States" setting.3GPP TS 25.213 Table 1B.1 defines the values for this parameter (also known as deltaE-DPDCH), which is used to determine the reference gain factor ßed,ref that is then used together with the reference E-TFCI to calculate the gain factor ßed for the selected E-TFCI based on the configured HARQ profile.The default value comes from 3GPP TS 34.108 s9.2.

Setting

Range: 8 comma separated values of 0 to 31

Resolution: 1

Query

*RST Setting

4,0,0,0,0,0,0,0

Requirements

Lab Application Revision: E.01 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:ETFCi:POFFsets:REFerence:MANual:POFFset 4,0,0,0,0,0,0,0" 
! Sets Reference E-TFCI Power Offset to 4,0,0,0,0,0,0,0.

Function

Sets/queries the Reference E-TFCI 1 to 8 States.

A maximum of 8 reference E-TFCs can be signaled to UE according to the 3GPP specifications. So, each position in this parameter's list corresponds one of these 8 reference E-TFCs. Only those positions that are set to "1" will be present in the RRC message sent to the UE.The default value comes from 3GPP TS 34.108 s9.2.

Setting

Range: 8 comma separated states (1|ON|0|OFF)

Query

*RST Setting

1,0,0,0,0,0,0,0

Requirements

Lab Application Revision: E.01 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:ETFCi:POFFsets:REFerence:MANual:STATe 1,0,0,0,0,0,0,0" 
! Sets Reference E-TFCI state 1 to On, and states 2 to 8 to Off.

Function

Sets/queries the E-TFCI Recording Behavior. This setting determines whether all E-DPDCH subframes are recorded, or only those that pass CRC checks.

This setting can only be changed when E-TFCI Recording State is idle.

Setting

Range: ALL|GCRC (Good CRC only)

Query

*RST Setting

GCRC

Requirements

Lab Application Revision: E.00.34 and above

Test Application Revision: A.13 and above.

Programming Example

 
OUTPUT 714;"CALL:HSUPa:ETFCi:RECord:BEHavior GCRC"
! Sets all E-DPDCH subframe values that pass CRC checks to be recorded.

Function

Sets/queries the E-TFCI Rec Count . This setting can only be changed when E-TFCI Recording State is idle.

Setting

Range: 1 to 50

Resolution: 1

Query

*RST Setting

15

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:ETFCi:RECord:COUNt 15"
! Sets the E-TFCI Rec Count to 15.

Function

Start Recording E-TFCI Values .

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:ETFCi:RECord:STARt"

Function

Stop Recording E-TFCI Values .

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:ETFCi:RECord:STOP" 
! Stop Recording E-TFCI Values.

Function

Sets/queries the E-TFCI Table Index (10 ms TTI) .

This setting can only be changed when the connection status is idle.

Setting

Range: 0 to 1

Resolution: 1

Query

*RST Setting

0

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:ETFCi:TINDex 0" 
! Sets the E-TFCI Table Index (10 ms TTI) to Table 0.

Function

Sets/queries the E-TFCI Table Index (2ms TTI). This setting controls whether the UE is instructed to use E-DCH Transport Block Size Table 0 or Table 1 from 3GPP TS 25.321 Annex B when the HSUPA TTI Mode is set to 2ms TTI (see CALL:HSUPa:EDCHannel:TTI ). The default value is set to match the generic RB Setup message from 3GPP TS 34.108 s9.1.

This setting can only be changed when the connection status is idle.

Setting

Range: 0 to 1

Resolution: 1

Query

*RST Setting

0

Requirements

Test Application Revision: A.13 and above

Lab Application Revision: E.01 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:ETFCi:TINDex:MS2 0" 
! Sets the E-TFCI Table Index (2 ms TTI) to Table 0.

Function

Sets/queries the E-TFCI Table Index (2 ms TTI with 16QAM) (See E-TFCI Table Index (2 ms TTI) / E-TFCI Table Index (2 ms TTI with 16QAM) ). This setting controls whether the UE is instructed to use 2ms TTI E-DCH Transport Block Size Table 2 or 3 (in 3GPP TS 25.321 v7a0 Annex B) when the E-DCH TTI is set to 2ms (see CALL:HSUPa:EDCHannel:TTI ).

This setting can only be changed when the connection status is idle.

Setting

Range: 2 |3

Query

*RST Setting

2

Requirements

Test Application Revision: A.17.00 and above
Lab Application Revision: G.01.00 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:ETFCi:TINDex:MS2:QAM16 2" 
! Sets the E-TFCI Table Index (2 ms TTI with 16QAM) to Table 2.

Function

Sets/queries the HARQ Maximum Number of Retransmissions .

Setting

Range: 0 to 15

Resolution: 1

Query

*RST Setting

Requirements

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:HARQ:RETRans:MAXimum 7" 
! Sets HARQ Number of Retransmissions.

Function

Sets/queries the Happy Bit Avg Period .

Setting

Range: 0.5 to 3600 seconds

Resolution: 0.5 seconds

Query

*RST Setting

Requirements

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:HBIT:APERiod 1" 
! Sets the Happy Bit Average Period to 1 seconds.

Function

Sets/queries the Happy Bit Delay Cond .

Setting

Range: MS2 | MS10 | MS20 | MS50 | MS100 | MS200 | MS500 | MS1000

Query

*RST Setting

Requirements

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:HBIT:DCONdition MS100" 
! Sets the Happy Bit Delay Condition to 100 MS.

Function

Queries the UE reported E-DCH Category. See Rep EDCH Cat/Ext .

Query

*RST Setting

NREP

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:MS:REPorted:EDCHannel:CATegory?" 
! Queries the UE Reported E-DCH Category.

Function

Queries the UE reported E-DCH Category Extension. See Rep EDCH Cat/Ext .

Query

*RST Setting

Requirements

Test Application Revision: A.17 and above, with the required feature license
Lab Application Revision: G.01.00 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:MS:REPorted:EDCHannel:CATegory:Extension?" 
! Queries the UE Reported E-DCH Category Extension.

Function

Queries the Last Happy Bit .

Query

*RST Setting

Requirements

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:MS:REPorted:HBIT?" 
! Queries the Last Happy Bit.

Function

Queries the Happy Bit Ratio .

Query

Range: 0.0 to 100.0 %, 9.91E+37

Resolution: 0.1 %

*RST Setting

Requirements

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:MS:REPorted:HBIT:RATio?" 
! Queries the Happy Bit Ratio.

Function

Sets/queries PS Data E-DPDCH Max Channel Codes .

This setting is used to control the value for E-DPDCH Max Channelisation Codes that is signaled to the UE at the setup of a PDP Context that uses 10ms TTI or 2ms TTI on the E-DCH depending on the setting of "HSUPA TTI Mode." The default for this parameter is set to allow the maximum data throughput that is possible when using 10ms TTI. When using 2ms TTI, in order to get maximum data throughput, this parameter must be set to "2SF2+2SF4."The value "2SF2+2SF4" is only available when "UTRA FDD GPRS Service Radio Access Bearer" is setto "HSUPA UL/HSDPA DL PS" and "HSPA PS Data SRB Mapping Mode" is set to "E-DCH/DCH," which means SRBs are mapped onto E-DCH/DCH and no uplink DPDCH is configured.If "UTRA FDD GPRS Service Radio Access Bearer" is not set to "HSUPA UL/HSDPA DL PS," this parameter is ignored.

This setting can only be changed when the connection status is Idle.

Setting

Range:

• SF256|SF128|SF64|SF32|SF16|SF8|SF4
• TSF4 (2sf4)
• TSF2 (2sf2)
• T2T4 (2sf2+2sf4)

Query

*RST Setting

TSF2

Requirements

Lab Application Revision: U.00.13 and above

Lab Application Revision: E.01 and above, added T2T4

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SERVice:PSData:EDPDchannel:CCODes:MAX TSF2" 
! Sets the PS Data E-DPDCH Max Channel Codes to 2sf2.

Function

Sets/queries PS Data E-RGCH Information State .

This setting can only be changed when the connection status is Idle.

Setting

Range: 1|ON|0|OFF

Query

*RST Setting

1 (ON)

Requirements

Lab Application Revision: U.00.13 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SERVice:PSData:ERGChannel:INFormation ON" 
! Sets the RB Test Mode E-RGCH Information State to On.

Function

Sets/queries PS Data MAC-d PDU Size.

Setting

Range: 336 to 5000 in increments of 8.

Query

*RST Setting

Requirements

Lab Application Revision: G.00.00 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SERVice:PSData:MACD:PDUSize 336"
! Sets PS Data MAC-d PDU Size to 336 Bits.

Function

Sets/queries RB E-DPDCH Max Channel Codes (12.2k + HSPA) .

This setting can only be changed when the connection status is Idle.

Setting

Range:

• SF256|SF128|SF64|SF32|SF16|SF8|SF4
• TSF4 (2sf4)
• TSF2 (2sf2)

Query

*RST Setting

TSF4

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SERVice:RBTest:EDPDchannel:CCODes:MAX TSF4" 
! Sets the RB Test Mode E-DPDCH Max Channel Codes to 2sf4.

Function

Sets/queries RB Test Mode E-DPDCH Max Channelisation Codes (HSPA Only). This setting is used to control the value for E-DPDCH Max Channelisation Codes that is signaled to the UE at the setup of an RB Test Mode call when "UTRA FDD RB Test Mode Channel Type" is set to "HSPA Only." The default value for this parameter is set to match 3GPP TS 34.108 s9.2.If "UTRA FDD RB Test Mode Channel Type" is set to"12.2k RMC+HSPA," this parameter is ignored.

Setting

Range:

• SF256|SF128|SF64|SF32|SF16|SF8|SF4
• TSF4 (2sf4)
• TSF2 (2sf2)
• T2T4 (2sf2+2sf4)

Query

*RST Setting

T2T4

Requirements

Test Application Revision: A.13 and above, with the required feature license

Lab Application Revision: E.01 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SERVice:RBTest:EDPDchannel:CCODes:MAX:HSPA T2T4" 
! Sets the RB Test Mode E-DPDCH Max Channel Codes (HSPA Only) to 2sf2+2sf4.

Function

Sets/queries the RB Test Mode E-RGCH Information State .

This setting can only be changed when the connection status is Idle.

Setting

Range: 1|ON|0|OFF

Query

*RST Setting

0

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SERVice:RBTest:ERGChannel:INFormation OFF" 
! Sets the RB Test Mode E-RGCH Information State to Off.

Function

Sets/queries the RB Test Mode E-DCH Maximum Number of HARQ Retransmissions.

This setting controls the maximum number of retransmissions a HARQ process in the UE will perform for a given block of data before giving up and moving onto a new block of data under an HSUPA RB test mode call. The default value was chosen to match both 3GPP TS 34.108 s9.1 and s9.2.Note: This parameter applies to two MAC-d flows when SRBs are mapped onto E-DCH/DCH.This setting is only available in the lab application (LA). In the test application (TA) this parameter is fixed to 7.

Setting

Range: 0 to 15

Resolution: 1

Query

*RST Setting

7

Requirements

Lab Application Revision: E.01 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SERVice:RBTest:HARQ:RETRans:MAXimum 7" 
! Sets the RB Test Mode E-DCH Maximum Number of HARQ Retransmissions to 7.

Function

Sets/queries the E-DCH RLC PDU Size.

Setting

Range: BITS336|BITS112

Query

*RST Setting

BITS336

Requirements

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SERVice:RBTest:RLCPdu:SIZE BITS336" 
! Sets the E-DCH RLC PDU Size to 336.

Function

Sets/queries the RB E-DPDCH Max Channel Codes (HSPA) .

This setting can only be changed when the connection status is Idle.

Setting

Range: BITS2936|BITS5872|BITS8808|BITS11744|BITS14765|BITS29360|BITS35232

Query

*RST Setting

BITS2936

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SERVice:RBTest:RLCSdu:SIZE BITS2936" 
! Sets the E-DCH RLC SDU Size to 2936.

Function

Setting

Range: DTXA[1]|ZGRant|INDex2|INDex3...|INDex31

Query

*RST Setting

ZGR

Requirements

Test Application Revision: A.17 and above, with the required feature license

Lab Application Revision: G.01.00 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue ZGRant" 
! Sets the Absolute Grant Pattern - Value 1 to ZERO_GRANT.

Function

When the E-DCH TTI is 2 ms , the E-DCH 16QAM State is On and the BetaEd Gain E-AGCH Table Selection is set to 1, this command sets/queries the Absolute Grant Pattern - Value 2. .This setting cannot be changed when AG Mode is set to Pattern .

Setting

Range: DTXA[1]|ZGRant|INDex2|INDex3...|INDex31

Query

*RST Setting

Requirements

Test Application Revision: A.17.00 and above, with the required feature license

Lab Application Revision: G.01.00 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue2 ZGRant" 
! Sets the Absolute Grant Pattern - Value 2 to ZERO_GRANT.

Function

When the E-DCH TTI is 2 ms , the E-DCH 16QAM State is On and the BetaEd Gain E-AGCH Table Selection is set to 1, this command sets/queries the Absolute Grant Pattern - Value 3 . This setting cannot be changed when AG Mode is set to Pattern .

Setting

Range: DTXA[1]|ZGRant|INDex2|INDex3...|INDex31

Query

*RST Setting

Requirements

Test Application Revision: A.17.00 and above, with the required feature license

Lab Application Revision: G.01.00 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue3 INDex31" 
! Sets the Absolute Grant Pattern - Value 3 to 31:4(377/15)^2.

Function

When the E-DCH TTI is 2 ms , the E-DCH 16QAM State is On and the BetaEd Gain E-AGCH Table Selection is set to 1, this command sets/queries the Absolute Grant Pattern - Value 4. This setting cannot be changed when AG Mode is set to Pattern .

Setting

Range: DTXA[1]|ZGRant|INDex2|INDex3...|INDex31

Query

*RST Setting

Requirements

Test Application Revision: A.17.00 and above, with the required feature license

Lab Application Revision: G.01.00 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue4 INDex31" 
! Sets the Absolute Grant Pattern - Value 4 to 31:4(377/15)^2.

Function

When the E-DCH TTI is 2 ms , the E-DCH 16QAM State is On and the BetaEd Gain E-AGCH Table Selection is set to 1, this command sets/queries the Absolute Grant Pattern - Value 5. This setting cannot be changed when AG Mode is set to Pattern .

Setting

Range: DTXA[1]|ZGRant|INDex2|INDex3...|INDex31

Query

*RST Setting

Requirements

Test Application Revision: A.17.00 and above, with the required feature license

Lab Application Revision: G.01.00 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue5 INDex31" 
! Sets the Absolute Grant Pattern - Value 5 to 31:4(377/15)^2.

Function

When the E-DCH TTI is 2 ms , the E-DCH 16QAM State is On and the BetaEd Gain E-AGCH Table Selection is set to 1, this command sets/queries the Absolute Grant Pattern - Value 6. This setting cannot be changed when AG Mode is set to Pattern .

Setting

Range: DTXA[1]|ZGRant|INDex2|INDex3...|INDex31

Query

*RST Setting

Requirements

Test Application Revision: A.17.00 and above, with the required feature license

Lab Application Revision: G.01.00 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue6 INDex31" 
! Sets the Absolute Grant Pattern - Value 6 to 31:4(377/15)^2.

Function

When the E-DCH TTI is 2 ms , the E-DCH 16QAM State is On and the BetaEd Gain E-AGCH Table Selection is set to 1, this command sets/queries the Absolute Grant Pattern - Value 7. This setting cannot be changed when AG Mode is set to Pattern .

Setting

Range: DTXA[1]|ZGRant|INDex2|INDex3...|INDex31

Query

*RST Setting

Requirements

Test Application Revision: A.17.00 and above, with the required feature license

Lab Application Revision: G.01.00 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue7 INDex31" 
! Sets the Absolute Grant Pattern - Value 7 to 31:4(377/15)^2.

Function

When the E-DCH TTI is 2 ms , the E-DCH 16QAM State is On and the BetaEd Gain E-AGCH Table Selection is set to 1, this command sets/queries the Absolute Grant Pattern - Value 8. This setting cannot be changed when AG Mode is set to Pattern .

Setting

Range: DTXA[1]|ZGRant|INDex2|INDex3...|INDex31

Query

*RST Setting

Requirements

Test Application Revision: A.17.00 and above, with the required feature license

Lab Application Revision: G.01.00 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:ALTernative:PATTern:VALue8 INDex31" 
! Sets the Absolute Grant Pattern - Value 8 to 31:4(377/15)^2.

Function

Sets/queries the Single Shot AG .

Setting

Range: ZGRant|INDex2|INDex3...|INDex31

Query

*RST Setting

IND31

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:ALTernative:SSHot INDex31" 
! Sets the Single Shot Absolute Grant to 31:6(168/15)^2.

Function

Sets/queries the AG Mode .

Setting

Range: SSHot|PATTern

Query

*RST Setting

SSH

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:MODE SSHot" 
! Sets the AG Mode to Single Shot.

Function

Sets/queries the Absolute Grant Pattern Length.

This setting controls the number of values in a pattern on the E-AGCH that are transmitted to the UE when CALL:HSUPa:SGRant:ABSolute:MODE is set to PATTern.

Setting

Range: 2 to 8

Resolution: 1

Query

*RST Setting

2

Requirements

Lab Application Revision: F.00 and above

Test Application Revision: A.14 and above, with the required feature license

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:PATTern:LENGth 2" 
! Sets the Absolute Grant Pattern Length to 2.

Function

Sets/queries the Absolute Grant Pattern - Length . This setting cannot be changed when AG Mode is set to Pattern .

Setting

Range: DTXA[1]|ZGRant|INDex2|INDex3...|INDex31

Query

*RST Setting

ZGR

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:PATTern:VALue ZGRant" 
! Sets the Absolute Grant Pattern - Value 1 to ZERO_GRANT.

Function

Sets/queries the Absolute Grant Pattern - Value 2 (see Absolute Grant Pattern Values ). This setting cannot be changed when AG Mode is set to Pattern .

Setting

Range: DTXA[1]|ZGRant|INDex2|INDex3...|INDex31

Query

*RST Setting

IND31

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:PATTern:VALue2 INDex31" 
! Sets the Absolute Grant Pattern - Value 2 to 31:6(168/15)^2.

Function

Sets/queries the Absolute Grant Pattern - Value 3. This setting cannot be changed when AG Mode is set to Pattern .

Setting

Range: DTXA[1]|ZGRant|INDex2|INDex3...|INDex31

Query

*RST Setting

IND31

Requirements

Lab Application Revision: F.00 and above

Test Application Revision: A.14 and above, with the required feature license

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:PATTern:VALue3 INDex31" 
! Sets the Absolute Grant Pattern - Value 2 to 31:6(168/15)^2.

Function

Sets/queries the Absolute Grant Pattern - Value 4. This setting cannot be changed when AG Mode is set to Pattern .

Setting

Range: DTXA[1]|ZGRant|INDex2|INDex3...|INDex31

Query

*RST Setting

IND31

Requirements

Lab Application Revision: F.00 and above

Test Application Revision: A.14 and above, with the required feature license

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:PATTern:VALue4 INDex31" 
! Sets the Absolute Grant Pattern - Value 2 to 31:6(168/15)^2.

Function

Sets/queries the Absolute Grant Pattern - Value 5. This setting cannot be changed when AG Mode is set to Pattern .

Setting

Range: DTXA[1]|ZGRant|INDex2|INDex3...|INDex31

Query

*RST Setting

IND31

Requirements

Lab Application Revision: F.00 and above

Test Application Revision: A.14 and above, with the required feature license

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:PATTern:VALue5 INDex31" 
! Sets the Absolute Grant Pattern - Value 2 to 31:6(168/15)^2.

Function

Sets/queries the Absolute Grant Pattern - Value 6. This setting cannot be changed when AG Mode is set to Pattern .

Setting

Range: DTXA[1]|ZGRant|INDex2|INDex3...|INDex31

Query

*RST Setting

IND31

Requirements

Lab Application Revision: F.00 and above

Test Application Revision: A.14 and above, with the required feature license

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:PATTern:VALue6 INDex31" 
! Sets the Absolute Grant Pattern - Value 2 to 31:6(168/15)^2.

Function

Sets/queries the Absolute Grant Pattern - Value 7. This setting cannot be changed when AG Mode is set to Pattern .

Setting

Range: DTXA[1]|ZGRant|INDex2|INDex3...|INDex31

Query

*RST Setting

IND31

Requirements

Lab Application Revision: F.00 and above

Test Application Revision: A.14 and above, with the required feature license

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:PATTern:VALue7 INDex31" 
! Sets the Absolute Grant Pattern - Value 2 to 31:6(168/15)^2.

Function

Sets/queries the Absolute Grant Pattern - Value 8. This setting cannot be changed when AG Mode is set to Pattern .

Setting

Range: DTXA[1]|ZGRant|INDex2|INDex3...|INDex31

Query

*RST Setting

IND31

Requirements

Lab Application Revision: F.00 and above

Test Application Revision: A.14 and above, with the required feature license

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:PATTern:VALue8 INDex31" 
! Sets the Absolute Grant Pattern - Value 2 to 31:6(168/15)^2.

Function

Sets/queries the RB Setup AG . This setting can only be changed when the connection status is idle.

Setting

Range: ZGRant|INDex0|INDex1|INDex2|INDex3...|INDex37|INDex38

Query

*RST Setting

IND37

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Lab Application Revision: G.01 and above: Added INDex38

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:RBSetup INDex37" 
! Sets the RB Setup Absolute Grant to 37:6(168/15)^2.

Function

Sets/queries the RB Setuo AG (16QAM). This set of values is used when the E-DCH TTI is 2 ms and the E-DCH 16QAM State is set to On .

This setting can only be changed when the connection status is idle.

Setting

Range: ZGRant|INDex0|INDex1|INDex2|INDex3...|INDex38

Query

*RST Setting

IND37

Requirements

Test Application Revision: A.17.00 and above
Lab Application Revision: G.01.00 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:RBSetup:QAM16 INDex37" 
! Sets the RB Setup Absolute Grant (16QAM)to 37:4(377/15)^2.

Function

Sets/queries the Single Shot AG .

Setting

Range: ZGRant|INDex2|INDex3...|INDex31

Query

*RST Setting

IND31

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:SSHot INDex31" 
! Sets the Single Shot Absolute Grant to 31:6(168/15)^2.

Function

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:ABSolute:SSHot:SEND" 
! Send Single Shot AG.

Function

Initiates the Send Relative Grant Down action.

This action is rejected if RB Test Mode E-RGCH Information State is Off . A warning is posted if you initiate this action when HSPA Cell 1 Connected E-RGCH Level is Off .

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:RELative:DOWN:SEND" 
! Send Relative Grant Down

Function

Sets/queries the RG Mode .

Setting

Range: Single|Continuous

Query

*RST Setting

Requirements

Lab Application Revision: G.00.00 and above

Lab Application Revision: I.00.00 and above, changed the range from SSHot|PATTern to Single|Continuous

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:RELative:MODE Single" 
! Sets the RG Mode to Single Shot.

Function

Sets/queries the Relative Grant Pattern.

Setting

Range: HOLD|UP|DOWN|D12Hold8 | D4Hold8|MANual

Query

*RST Setting

HOLD

Requirements

Lab Application Revision: G.00.00 and above
Lab Application Revision: G.01.00: Added D12H8
Lab Application Revision H.01.00: Added D4Hold8

Lab Application Revision I.00.00: Added MANual

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:RELative:PATTern HOLD" 
! Sets the RG Pattern to All Holds.

Function

Sets/queries the sequence of relative grant pattern transmitted on E-RGCH.

This setting is applicable when RG Mode is set to Pattern and RG Pattern is set to Manual .

Changing the setting when RG Mode is set to Pattern will post +530 error message: "FDD call processing error; Relative grant pattern values cannot be changed while the relative grant mode is set to pattern." Before changing the setting, you need to set RG Mode to Single Shot.

Setting

Range: {1-2}, {HOLD|UP|DOWN}, {1-256}, {HOLD|UP|DOWN}, {1-256}

Description: {E-RGCH Pattern Number of Segments}, {E-RGCH Pattern First Segment Command Type}, {E-RGCH Pattern First Segment Length}, {E-RGCH Pattern Second Segment Command Type}, {E-RGCH Pattern Second Segment Length}

Query

*RST Setting

2, DOWN, 12, HOLD, 8

Requirements

Lab Application Revision I.00.00:

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:RELative:PATTern:MANual 2,DOWN,12,HOLD,8" 
! Sets the sequence of RG Pattern to 2,DOWN,12,HOLD,8.

Function

Sets/queries the E-RGCH Pattern Periodic Transmission State. If set to On , the test set transmits a periodic sequence of values to the UE over the E-RGCH immediately. If set to Off , when an CALL:HSUPa:SGRant:RELative:PATTern:SEND[:IMMediate] action is performed, the test set transmits a sequence of values to the UE over the E-RGCH only once. The values that are transmitted to the UE are defined by RG Pattern

This setting is only applicable when the RG Mode is set to Pattern and the RG Pattern is set to 12 Downs + 8 Holds .

This setting can not be changed while the RG Mode is set to Pattern .

This setting is GPIB only.

Setting

Range: 1|On|0|Off

Query

Range: 1|0

*RST Setting

1 (On)

Requirements

Test Application Revision: A.17.00 and above
Lab Application Revision: G.01.00 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:RELative:PATTern:PERiodic On" 
! Sets the RG Pattern Periodic Transmission State to On.

Function

Transmit a finite sequence of values to the UE over the E-RGCH. The values that are transmitted to the UE are defined by RG Pattern .

This setting is only applicable when the RG Mode is set to Pattern , the RG Pattern is set to 12 Downs + 8 Holds and the CALL:HSUPa:SGRant:RELative:PATTern:PERiodic[:STATe] is set to Off.

This setting is only applicable when the E-DCH is active.

Requirements

Test Application Revision: A.17.00 and above
Lab Application Revision: G.01.00 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:RELative:PATTern:SEND" 

Function

Initiates the Clear Queued Relative Grants action.

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:RELative:QUEued:CLEar" 
! Clear Queued Relative Grants.

Function

Initiates the Send Relative Grant Up action.

This action is rejected if RB Test Mode E-RGCH Information State is Off . A warning is posted if you initiate this action when HSPA Cell 1 Connected E-RGCH Level is Off .

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SGRant:RELative:UP:SEND" 
! Send Relative Grant Up.

Function

Sets/queries the Scheduling Information Periodicity (Grant) .

Setting

Range: NREPort | EETTi|MS4 | MS10 | MS20 | MS50 | MS100 | MS200 | MS500 | MS1000

Query

*RST Setting

NREPort

Requirements

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SIPeriod:GRANt NREPort" 
! Sets the Scheduling Information Periodicity (Grant) to NREPort.

Function

Sets/queries the Scheduling Information Periodicity (No Grant) .

Setting

Range: NREPort | EETTi|MS4 | MS10 | MS20 | MS50 | MS100 | MS200 | MS500 | MS1000

Query

*RST Setting

NREPort

Requirements

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:HSUPa:SIPeriod:NGRant NREPort" 
! Sets the Scheduling Information Periodicity (No Grant) to NREPort.