CALL:SETup

Function

Sets/queries the Handover Band Arbitrator .

This setting is only applicable when Handover Downlink Channel (UARFCN) is set to a channel in Band VI.

Setting

Range: BAND5|BAND6

Query

*RST Setting

BAND6

Test Application Revision: A.09 and above

Test Application Revision A.11, added [:PCReconfig]

Lab Application Revision: C.04 and above

Lab Application Revision: D.00 and above

Lab Application Revision D.02, added [:PCReconfig]

Programming Example

 
OUTPUT 714;"CALL:SETup:CHANnel:BARBitrator BAND5"

Function

Sets/queries the Handover Downlink Channel (UARFCN) .

If the entered Handover Downlink Channel (UARFCN) has an uplink/downlink offset of less than 30 MHz when compared with the Handover Uplink Channel (UARFCN) , the warning message "+217, Performance not specified for UL/DL frequency offset < 30 MHz" will be issued. The setting will be used as entered if not changed by the user.

Setting

Range:

• 412, 437, 462, 487, 512, 537, 562, 587, 612, 637, 662, 687
• 1007, 1012, 1032, 1037, 1062, 1087
• 1162 - 1513, resolution = 1
• 1537 - 1738, resolution = 1
• 1887, 1912, 1937, 1962, 1987, 2012, 2037, 2062, 2087
• 2237 - 2563, resolution = 1
• 2587, 2612, 2637, 2662, 2687, 2712, 2737, 2762, 2787, 2812, 2837, 2862, 2887, 2912
• 2937 - 3088, resolution = 1
• 3112 to 3388, resolution = 1
• 3412, 3437, 3462, 3487, 3512, 3537, 3562, 3587, 3612, 3637, 3662, 3687
• 3837 - 3903, resolution = 1
• 3927, 3932, 3957, 3962, 3987, 3992
• 4017 - 4043, resolution = 1
• 4067, 4092
• 4117 - 4143, resolution = 1
• 4167, 4192
• 4357 - 4458, resolution = 1
• 9237 - 9387, resolution = 1
• 9662 - 9938, resolution = 1
• 10562 - 10838, resolution = 1

Query

*RST Setting

10730

Test Application Revision: A.02 and above.

Lab Application Revision: A.01 and above.

Test Application Revision A.05.28, Lab Application Revision B.01.29, added 1037 - 1062.

Test Application Revision A.08 and Lab Application Revision C.03, changed channel ranges to match 3GPP TS 25.101 v6.7.0 (previously, channels supported were: 412-687, 1037-1062, 4320-4495, 4600-4825, 9000-9425, 9625-9975, and 10,525-10,875, resolution = 1).

Test Application Revision A.09 and Lab Application Revision C.04 and D.00, changed channel ranges to match 3GPP TS 25.101 v7.2.0 (previously channels supported were: 412, 437, 462, 487, 512, 537, 562, 587, 612, 637, 662, 687, 1007, 1012, 1032, 1037, 1062, 1087, 1462, 1487, 1512, 1537, 1562, 1587, 1612, 1637, 1662, 4357-4458 -- resolution = 1, 9037-9388 -- resolution = 1, 9662-9938 -- resolution = 1, and 10562-10838 -- resolution = 1).

Test Application Revision A.10 and Lab Application Revision D.01, added 2237 - 2563, 2587, 2612, 2637, 2662, 2687, 2712, 2737, 2762, 2787, 2812, 2837, 2862, 2887, 2912

Test Application Revision A.11 and Lab Application Revisions D.02 and E.00, added 3112 to 3388, 3412, 3437, 3462, 3487, 3512, 3537, 3562, 3587, 3612, 3637, 3662, 3687

Test Application Revision A.11 and Lab Application Revision D.02, added [:PCReconfig]

Test Application Revision A.14 and Lab Application Revision F.00, added 3837 - 3903, 3927, 3932, 3957, 3962, 3987, 3992, 4017 - 4043, 4067, 4092, 4117 - 4143, 4167, 4192

Programming Example

 
OUTPUT 714;"CALL:SETup:CHANnel:DOWNlink 10735"

Function

The setting form of this command performs two functions: (1) sets Handover Uplink Channel (UARFCN) to a specific UARFCN (see CALL:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>:UPLink:CHANnel ), and (2) sets handover uplink channel control to off (manual) (see CALL:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>:UPLink:CONTrol:AUTO ).

The query form of this command returns the handover uplink UARFCN that is used by the test set when CALL:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>:UPLink:CONTrol:AUTO is set to off (manual). Note, when CALL:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>:UPLink:CONTrol:AUTO is set to on (auto), the handover uplink UARFCN used by the test set is determined by CALL:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>:DOWNlink .

The handover uplink UARFCN being used by the test set at any given time can be determined by CALL:STATus:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>UPLink[:CHANnel]? .

If the entered handover Handover Uplink UARFCN has an uplink/downlink offset of less than 30 MHz when compared with the Handover Downlink Channel (UARFCN) , the warning message "+217, Performance not specified for UL/DL frequency offset < 30 MHz" will be issued. The setting will be used as entered if not changed by the user.

Setting

Range: see CALL:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>:UPLink:CHANnel

Query

*RST Setting

Handover uplink UARFCN = 9780, handover uplink channel control = on (auto)

Test Application Revision: A.02 and above.

Lab Application Revision: A.01 and above.

Test Application Revision A.05.28 and Lab Application Revision B.01.29, added 812 - 837.

Test Application Revision A.08 and Lab Application Revision C.03, changed channel ranges to match 3GPP TS 25.101 v6.7.0 (previously, channels supported were: 12-287, 812-837, 4095-4270, 4375-4600, 8525-8950 and 9225-9925, resolution = 1).

Test Application Revision A.09 and Lab Application Revision C.04 and D.00, changed channel ranges to match 3GPP TS 25.101 v7.2.0 (previously channels supported were: 12, 37, 62, 87, 112, 137, 162, 187, 212, 237, 262, 287, 782, 787, 807, 812, 837, 862, 1162, 1187, 1212, 1237, 1262, 1287, 1312, 1337, 1362, 4132-4233 -- resolution = 1, 8562-8913 -- resolution = 1, 9262-9538 -- resolution = 1, 9612-9888 -- resolution = 1).

Test Application Revision A.10 and Lab Application Revision D.01, added 2012 - 2338, 2362, 2387, 2412, 2437, 2462, 2487, 2512, 2537, 2562, 2587, 2612, 2637, 2662, 2687

Test Application Revision A.11 and Lab Application Revisions D.02 and E.00, added 2887 to 3163, 3187, 3212, 3237, 3262, 3287, 3312, 3337, 3362, 3387, 3412, 3437, 3462

Test Application Revision A.11 and Lab Application Revision D.02, added [:PCReconfig]

Lab Application Revision: E.00.34 and above, added 3487 - 3587.

Programming Example

 
OUTPUT 714;"CALL:SETup:CHANnel:UPLink 9785"
! Sets the handover uplink channel UARFCN to 9785 and selects manual control mode
! for handover uplink channel.

Function

The setting form of this command sets Handover Uplink Channel (UARFCN) to a specific UARFCN.

Note, this handover uplink UARFCN is only used by the test set when CALL:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>:UPLink:CONTrol:AUTO is set to off (manual). When CALL:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>:UPLink:CONTrol:AUTO is set to on (auto), the handover uplink UARFCN used by the test set is determined by CALL:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>:DOWNlink .

The query form of this command returns the handover uplink UARFCN that is used by the test set when CALL:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>:UPLink:CONTrol:AUTO is set to off (manual).

The handover uplink UARFCN being used by the test set at any given time can be determined by CALL:STATus:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>UPLink[:CHANnel]? .

If the entered handover Handover Uplink UARFCN has an uplink/downlink offset of less than 30 MHz when compared with the Handover Downlink Channel (UARFCN) , the warning message "+217, Performance not specified for UL/DL frequency offset < 30 MHz" will be issued. The setting will be used as entered if not changed by the user.

Setting

Range:

• 12, 37, 62, 87, 112, 137, 162, 187, 212, 237, 262, 287
• 782, 787, 807, 812, 837, 862
• 937 - 1288, resolution = 1
• 1312 - 1513, resolution = 1
• 1662, 1687, 1712, 1737, 1762, 1787, 1812, 1837, 1862
• 2012 - 2338, resolution = 1
• 2362, 2387, 2412, 2437, 2462, 2487, 2512, 2537, 2562, 2587, 2612, 2637, 2662, 2687
• 2712 - 2863, resolution = 1
• 2887 - 3163, resolution = 1
• 3187, 3212, 3237, 3262, 3287, 3312, 3337, 3362, 3387, 3412, 3437, 3462
• 3487 - 3587, resolution = 1
• 3612 - 3678, resolution = 1
• 3702, 3707, 3732, 3737, 3762, 3767
• 3792 - 3818, resolution = 1
• 3842, 3867
• 3892 - 3918, resolution = 1
• 3942, 3967
• 4132 - 4233, resolution = 1
• 8762 - 8912, resolution = 1
• 9262 - 9538, resolution = 1
• 9612 - 9888, resolution = 1

Query

*RST Setting

Test Application Revision: A.06 and above

Lab Application Revision: C.01 and above

Test Application Revision A.08 and Lab Application Revision C.03, changed channel ranges to match 3GPP TS 25.101 v6.7.0 (previously, channels supported were: 12-287, 812-837, 4095-4270, 4375-4600, 8525-8950 and 9225-9925, resolution = 1).

Test Application Revision A.09 and Lab Application Revision C.04 and D.00, changed channel ranges to match 3GPP TS 25.101 v7.2.0 (previously channels supported were: 12, 37, 62, 87, 112, 137, 162, 187, 212, 237, 262, 287, 782, 787, 807, 812, 837, 862, 1162, 1187, 1212, 1237, 1262, 1287, 1312, 1337, 1362, 4132-4233 -- resolution = 1, 8562-8913 -- resolution = 1, 9262-9538 -- resolution = 1, 9612-9888 -- resolution = 1).

Test Application Revision A.10 and Lab Application Revision D.01, added 2012 - 2338, 2362, 2387, 2412, 2437, 2462, 2487, 2512, 2537, 2562, 2587, 2612, 2637, 2662, 2687

Test Application Revision A.11 and Lab Application Revisions D.02 and E.00, added 2887 to 3163, 3187, 3212, 3237, 3262, 3287, 3312, 3337, 3362, 3387, 3412, 3437, 3462

Test Application Revision A.11 and Lab Application Revision D.02, added [:PCReconfig]

Lab Application Revision: E.00.34 and above, added 3487 - 3587.

Test Application Revision A.14 and Lab Application Revision F.00 and above, added 3612 - 3678, 3702, 3707, 3732, 3737, 3762, 3767, 3792 - 3818, 3842, 3867, 3892 - 3918, 3942, 3967

Programming Example

 
OUTPUT 714;"CALL:SETup:CHANnel:UPLink:CHANnel 9785"
! Sets the handover uplink channel UARFCN to 9785.

Function

Sets/queries the Handover Uplink Channel (UARFCN) control mode.

• Auto - handover uplink UARFCN is determined by CALL:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>:DOWNlink .
• Manual - handover uplink UARFCN is determined by CALL:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>:UPLink:CHANnel .

The handover uplink UARFCN being used by the test set at any given time can be determined by CALL:STATus:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>UPLink[:CHANnel]? .

Setting

Range:

• 1|ON (auto)
• 0|OFF (manual)

Query

*RST Setting

1 (auto)

Test Application Revision: A.06 and above

Test Application Revision A.11, added [:PCReconfig]

Lab Application Revision: C.01 and above

Lab Application Revision D.02, added [:PCReconfig]

Programming Example

 
OUTPUT 714;"CALL:SETup:CHANnel:UPLink:CONTrol:AUTO OFF"
! Sets handover uplink control mode to manual.

Function

THIS COMMAND IS OBSOLETE. The Handoff Uplink Separation (Band) setting has been replaced by the Handover Band Arbitrator setting ( CALL:SETup[:PCReconfig]:CHANnel:BARBitrator ). Setting CALL:SETup:CHANnel:UPLink:SEParation to VMHZ45 sets Handoff Band Arbitrator to Band 5 . Setting CALL:SETup:CHANnel:UPLink:SEParation to any other value sets Handoff Band Arbitrator to Band 6 .

Sets/queries Handoff Uplink Separation (Band) .

When CALL:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>:UPLink:CONTrol:AUTO is set to on (auto), the handoff uplink UARFCN used by the test set is determined by this Handoff Uplink Separation setting and by CALL:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>:DOWNlink .

If CALL:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>:UPLink:CONTrol:AUTO is set to on (auto) and you attempt to set Handoff Uplink Separation to a value that would result in an invalid handoff uplink channel based on the current CALL:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>:DOWNlink setting, an error is posted. With CALL:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>:UPLink:CONTrol:AUTO set to off (manual), set CALL:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>:DOWNlink and Handoff Uplink Separation to a valid combination, then set CALL:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>:UPLink:CONTrol:AUTO to on.

Setting

Range:

• MHZ45 - 45 MHz (Band 6)
• VMHZ45 - 45 MHz (Band 5)
• MHZ80 - 80 MHz (Band 2)
• MHZ95 - 95 MHz (Band 3)
• MHZ190 - 190 MHz (Band 1)
• MHZ400 - 400 MHz (Band 4)

Query

*RST Setting

Test Application Revision: A.06 and above

Test Application Revision A.08 and Lab Application Revision C.03, added VMHZ45

Lab Application Revision: C.01 and above

Programming Example

 
OUTPUT 714;"CALL:SETup:CHANnel:UPLink:SEParation MHZ80"

Function

Sets/queries Handover UL CL Power Ctrl Algorithm .

Setting

Range: ALG1|ALG2

Query

Requirements

Test Application Revision: A.10.01 and above.

Lab Application Revision: D.01.01 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:CLPControl:UPLink:ALGorithm ALG1"
! Sets Handover UL CL Power Ctrl Algorithm to One.

Function

Sets/queries Handover UL CL Power Ctrl Step Size .

This setting can only be changed when CALL:SETup:CLPControl:UPLink:ALGorithm is set to ALG1 . Also, if CALL:SETup:CLPControl:UPLink:ALGorithm is set to ALG2 , this setting is returned to its default value of 1 dB .

Setting

Range: 1 to 2 dB

Query

Requirements

Test Application Revision: A.10.01 and above.

Lab Application Revision: D.01.01 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:CLPControl:UPLink:STEPsize 2"
! Sets Handover UL CL Power Ctrl Step Size to 2 dB.

Function

Sets/queries the RBR Band Arbitrator .

This setting is only applicable when RBR Downlink Channel (UARFCN) is set to a channel in Band VI.

This setting is only applicable when RBR Channel (UARFCN) State is set to On .

Setting

Range: BAND5|BAND6

Query

*RST Setting

BAND6

Test Application Revision A.11 and above.

Lab Application Revision D.02 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:RBReconfig:CHANnel:BARBitrator BAND6"

Function

Sets/queries the RBR Downlink Channel (UARFCN) .

This setting is only applicable when RBR Channel (UARFCN) State is set to On .

If the entered RBR Downlink Channel (UARFCN) has an uplink/downlink offset of less than 30 MHz when compared with the RBR Uplink Channel (UARFCN) , the warning message "+217, Performance not specified for UL/DL frequency offset < 30 MHz" will be issued. The setting will be used as entered if not changed by the user.

Setting

Range:

• 412, 437, 462, 487, 512, 537, 562, 587, 612, 637, 662, 687
• 1007, 1012, 1032, 1037, 1062, 1087
• 1162 - 1513, resolution = 1
• 1537 - 1738, resolution = 1
• 1887, 1912, 1937, 1962, 1987, 2012, 2037, 2062, 2087
• 2237 - 2563, resolution = 1
• 2587, 2612, 2637, 2662, 2687, 2712, 2737, 2762, 2787, 2812, 2837, 2862, 2887, 2912
• 2937 - 3088, resolution = 1
• 3112 - 3388, resolution = 1
• 3412, 3437, 3462, 3487, 3512, 3537, 3562, 3587, 3612, 3637, 3662, 3687
• 3837 - 3903, resolution = 1
• 3927, 3932, 3957, 3962, 3987, 3992
• 4017 - 4043, resolution = 1
• 4067, 4092
• 4117 - 4143, resolution = 1
• 4167, 4192
• 4357 - 4458, resolution = 1
• 9237 - 9387, resolution = 1
• 9662 - 9938, resolution = 1
• 10562 - 10838, resolution = 1

Query

*RST Setting

10730

Test Application Revision A.11 and above.

Lab Application Revision D.02 and above.

Test Application Revision A.14 and Lab Application Revision F.00, added 3837 - 3903, 3927, 3932, 3957, 3962, 3987, 3992, 4017 - 4043, 4067, 4092, 4117 - 4143, 4167, 4192

Programming Example

 
OUTPUT 714;"CALL:SETup:RBReconfig:CHANnel:DOWNlink 10730"

Function

The setting form of this command performs two functions: (1) sets RBR Uplink Channel (UARFCN) to a specific UARFCN (see CALL:SETup:RBReconfig:CHANnel:UPLink:CHANnel ), and (2) sets RBR uplink channel control to off (manual) (see CALL:SETup:RBReconfig:CHANnel:UPLink:CONTrol:AUTO ).

The query form of this command returns the RBR uplink UARFCN that is used by the test set when CALL:SETup:RBReconfig:CHANnel:UPLink:CONTrol:AUTO is set to off (manual). Note, when CALL:SETup:RBReconfig:CHANnel:UPLink:CONTrol:AUTO is set to on (auto), the RBR uplink UARFCN used by the test set is determined by CALL:SETup:RBReconfig:CHANnel:DOWNlink .

This setting is only applicable when RBR Channel (UARFCN) State is set to On .

The RBR uplink UARFCN being used by the test set at any given time can be determined by CALL:STATus:SETup:RBReconfig:CHANnel:UPLink[:CHANnel]? .

If the entered RBR Uplink Channel (UARFCN) has an uplink/downlink offset of less than 30 MHz when compared with the RBR Downlink Channel (UARFCN) , the warning message "+217, Performance not specified for UL/DL frequency offset < 30 MHz" will be issued. The setting will be used as entered if not changed by the user.

Setting

Range: see CALL:SETup:RBReconfig:CHANnel:UPLink:CHANnel

Query

*RST Setting

RBR uplink UARFCN = 9780, RBR uplink channel control = on (auto)

Test Application Revision A.11 and above.

Lab Application Revision D.02 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:RBReconfig:CHANnel:UPLink 9780"
! Sets the RBR uplink channel UARFCN to 9780 and selects manual control mode
! for RBR uplink channel.

Function

The setting form of this command sets RBR Uplink Channel (UARFCN) to a specific UARFCN.

This setting is only applicable when RBR Channel (UARFCN) State is set to On .

Note, this RBR uplink UARFCN is only used by the test set when CALL:SETup:RBReconfig:CHANnel:UPLink:CONTrol:AUTO is set to off (manual). When CALL:SETup:RBReconfig:CHANnel:UPLink:CONTrol:AUTO is set to on (auto), the RBR uplink UARFCN used by the test set is determined by CALL:SETup:RBReconfig:CHANnel:DOWNlink .

The query form of this command returns the RBR uplink UARFCN that is used by the test set when CALL:SETup:RBReconfig:CHANnel:UPLink:CONTrol:AUTO is set to off (manual).

The RBR uplink UARFCN being used by the test set at any given time can be determined by CALL:STATus:SETup:RBReconfig:CHANnel:UPLink[:CHANnel]? .

If the entered RBR Uplink Channel (UARFCN) has an uplink/downlink offset of less than 30 MHz when compared with the RBR Downlink Channel (UARFCN) , the warning message "+217, Performance not specified for UL/DL frequency offset < 30 MHz" will be issued. The setting will be used as entered if not changed by the user.

Setting

Range:

• 12, 37, 62, 87, 112, 137, 162, 187, 212, 237, 262, 287
• 782, 787, 807, 812, 837, 862
• 937 - 1288, resolution = 1
• 1312 - 1513, resolution = 1
• 1662, 1687, 1712, 1737, 1762, 1787, 1812, 1837, 1862
• 2012 - 2338, resolution = 1
• 2362, 2387, 2412, 2437, 2462, 2487, 2512, 2537, 2562, 2587, 2612, 2637, 2662, 2687
• 2712 - 2863, resolution = 1
• 2887 - 3163, resolution = 1
• 3187, 3212, 3237, 3262, 3287, 3312, 3337, 3362, 3387, 3412, 3437, 3462
• 3487 - 3587, resolution = 1
• 3612 - 3678, resolution = 1
• 3702, 3707, 3732, 3737, 3762, 3767
• 3792 - 3818, resolution = 1
• 3842, 3867
• 3892 - 3918, resolution = 1
• 3942, 3967
• 4132 - 4233, resolution = 1
• 8762 - 8912, resolution = 1
• 9262 - 9538, resolution = 1
• 9612 - 9888, resolution = 1

Query

*RST Setting

Test Application Revision A.11 and above.

Lab Application Revision D.02 and above.

Lab Application Revision: E.00.34 and above, added 3487 - 3587.

Test Application Revision A.14 and Lab Application Revision F.00 and above, added 3612 - 3678, 3702, 3707, 3732, 3737, 3762, 3767, 3792 - 3818, 3842, 3867, 3892 - 3918, 3942, 3967

Programming Example

 
OUTPUT 714;"CALL:SETup:RBReconfig:CHANnel:UPLink:CHANnel 9780"
! Sets the RBR uplink channel UARFCN to 9780.

Function

Sets/queries the RBR Uplink Channel (UARFCN) control mode.

This setting is only applicable when RBR Channel (UARFCN) State is set to On .

• Auto - RBR uplink UARFCN is determined by CALL:SETup:RBReconfig:CHANnel:DOWNlink .
• Manual - RBR uplink UARFCN is determined by CALL:SETup:RBReconfig:CHANnel:UPLink:CHANnel .

The RBR uplink UARFCN being used by the test set at any given time can be determined by CALL:STATus:SETup:RBReconfig:CHANnel:UPLink[:CHANnel]? .

Setting

Range:

• 1|ON (auto)
• 0|OFF (manual)

Query

*RST Setting

1 (auto)

Test Application Revision A.11 and above.

Lab Application Revision D.02 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:RBReconfig:CHANnel:UPLink:CONTrol:AUTO ON"
! Sets RBR uplink control mode to auto.

Function

Sets/queries RBR Uplink DPCH Bc/Bd Control .

ON = automatic
OFF = manual

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

Requirements

Test Application Revision: A.09 and above.

Lab Application Revision: C.04 or D.00.04 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:RBReconfig:DPCHannel:BETA:AUTO OFF"
! Sets RBR Uplink DPCH Bc/Bd Control to Manual.

Function

Sets/queries RBR Default DPCH Offset (DOFF) .

This command is only applicable when CALL:HANDoff:RBReconfig:CFNHandling is set to INITialise.

Setting

Range: 0 to 5

Resolution: 1

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above.

Lab Application Revision: C.04 or D.00.04 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:RBReconfig:DPCHannel:DOFFset 3"
! Sets RBR Default DPCH Offset (DOFF) to 3 x 512 chips.

Function

Sets/queries RBR Manual Uplink DPCH Bc .

This command is only applicable when CALL:SETup:RBReconfig:DPCHannel:BETA:AUTO is set to OFF (Manual).

Setting

Range: 1 to 15

Resolution: 1

Query

Requirements

Test Application Revision: A.09 and above.

Lab Application Revision: C.04 or D.00.04 and above.

Test Application Revision A.11 and Lab Application Revisions D.02 and E.00, range is 1 to 15 (vs. 2 to 15)

Programming Example

 
OUTPUT 714;"CALL:SETup:RBReconfig:DPCHannel:MANual:CBETa 10"
! Sets RBR Manual Uplink DPCH Bc to 10.

Function

Sets/queries RBR Manual Uplink DPCH Bd .

This command is only applicable when CALL:SETup:RBReconfig:DPCHannel:BETA:AUTO is set to OFF (Manual).

Setting

Range: 0 to 15

Resolution: 1

Query

Requirements

Test Application Revision: A.09 and above.

Lab Application Revision: C.04 or D.00.04 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:RBReconfig:DPCHannel:MANual:DBETa 10"
! Sets RBR Manual Uplink DPCH Bd to 10.

Function

Sets/queries RBR Relative DPCH Frame Offset .

This command is only applicable when CALL:HANDoff:RBReconfig:CFNHandling is set to MAINtain.

Setting

Range: -256, 0, 256

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above.

Lab Application Revision: C.04 or D.00.04 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:RBReconfig:DPCHannel:RFOFfset -256"
! Sets RBR Relative DPCH Frame Offset to -256 chips.

Function

This command sets/queries the RBR Uplink DTCH RMC CRC Presence .

Setting

Range:

• PRESent
• DATa: (Used for Data)

Query

Test Application Revision: A.09 and above.

Lab Application Revision: C.04 or D.00.04 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:RBReconfig:DTCHannel:CRC DATa"
! Sets RBR Uplink DTCH RMC CRC Presence to Used for Data.

Function

Sets/queries the RBR UE Loopback Type .

Setting

Range: TYPE1|TYPE2

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above.

Lab Application Revision: C.04 or D.00.04 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:RBReconfig:MS:LOOPback:TYPE TYPE2"
! Sets RBR UE Loopback Type to Type 2.

Function

This command sets/queries the RB Test Mode RBR RAB .

Setting

Range:

• RMC12 (12.2k RMC)
• RMC64 (64k RMC)
• RMC144 (144k RMC)
• RMC384 (384k RMC)
• RMC33NC (33k No Coding RMC)

Query

Test Application Revision: A.09 and above.

Lab Application Revision: C.04 or D.00.04 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:RBReconfig:RBTest:RAB RMC64"
! Sets RB Test Mode RBR RAB to 64k RMC.

Function

Sets/queries the RBR Uplink Dummy DCCH Data state.

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

Requirements

Test Application Revision: A.09 and above.

Lab Application Revision: C.04 or D.00.04 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:RBReconfig:UPLink:DCCHannel:DDATa OFF"
! Sets RBR Uplink Dummy DCCH Data to Off

Function

THIS COMMAND IS OBSOLETE. Please use the CALL:HANDoff:SYSTem[:GSM][:IMMediate] command to perform a system handoff.

Sets/queries the system type that the mobile station will be handed off to when the CALL:HANDoff command is used. The intersystem handoff can be performed only from W-CDMA to GSM.

This setting cannot be changed to GSM while the E1968A test applications (TA) are not present in the test set and licensed for operation. Attempting to change this setting while the E1968A TA is not available will result in an error message to alert you this condition.

Setting

Range: FDD|GSM

Query

Range: FDD|GSM

*RST Setting

Test Application Revision: A.03 and above.

Lab Application Revision: A.01 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:SYSTem GSM" !Selects GSM as the handoff system type.

Function

Sets/queries RB Test Mode to GSM Handover Alerting State .

Setting

Range: 1|ON|0|OFF

Query

*RST Setting

Test Application Revision: A.06 and above.

Lab Application Revision: C.01 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:SYSTem:GSM:ALERting OFF"
! Sets RB Test Mode to GSM Alerting State to Off (the UE will not ring).

Function

Sets/queries the TCR Band Arbitrator .

This setting is only applicable when TCR Downlink Channel (UARFCN) is set to a channel in Band VI.

This setting is only applicable when TCR Channel (UARFCN) State is set to On .

Setting

Range: BAND5|BAND6

Query

*RST Setting

BAND6

Test Application Revision A.11 and above.

Lab Application Revision D.02 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:CHANnel:BARBitrator BAND6"

Function

Sets/queries the TCR Downlink Channel (UARFCN) .

This setting is only applicable when TCR Channel (UARFCN) State is set to On .

If the entered TCR Downlink Channel (UARFCN) has an uplink/downlink offset of less than 30 MHz when compared with the TCR Uplink Channel (UARFCN) , the warning message "+217, Performance not specified for UL/DL frequency offset < 30 MHz" will be issued. The setting will be used as entered if not changed by the user.

Setting

Range:

• 412, 437, 462, 487, 512, 537, 562, 587, 612, 637, 662, 687
• 1007, 1012, 1032, 1037, 1062, 1087
• 1162 - 1513, resolution = 1
• 1537 - 1738, resolution = 1
• 1887, 1912, 1937, 1962, 1987, 2012, 2037, 2062, 2087
• 2237 - 2563, resolution = 1
• 2587, 2612, 2637, 2662, 2687, 2712, 2737, 2762, 2787, 2812, 2837, 2862, 2887, 2912
• 2937 - 3088, resolution = 1
• 3112 - 3388, resolution = 1
• 3412, 3437, 3462, 3487, 3512, 3537, 3562, 3587, 3612, 3637, 3662, 3687
• 3837 - 3903, resolution = 1
• 3927, 3932, 3957, 3962, 3987, 3992
• 4017 - 4043, resolution = 1
• 4067, 4092
• 4117 - 4143, resolution = 1
• 4167, 4192
• 4357 - 4458, resolution = 1
• 9237 - 9387, resolution = 1
• 9662 - 9938, resolution = 1
• 10562 - 10838, resolution = 1

Query

*RST Setting

10730

Test Application Revision A.11 and above.

Lab Application Revision D.02 and above.

Test Application Revision A.14 and Lab Application Revision F.00, added 3837 - 3903, 3927, 3932, 3957, 3962, 3987, 3992, 4017 - 4043, 4067, 4092, 4117 - 4143, 4167, 4192

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:CHANnel:DOWNlink 10730"

Function

The setting form of this command performs two functions: (1) sets TCR Uplink Channel (UARFCN) to a specific UARFCN (see CALL:SETup:TCReconfig:CHANnel:UPLink:CHANnel ), and (2) sets TCR uplink channel control to off (manual) (see CALL:SETup:TCReconfig:CHANnel:UPLink:CONTrol:AUTO ).

The query form of this command returns the TCR uplink UARFCN that is used by the test set when CALL:SETup:TCReconfig:CHANnel:UPLink:CONTrol:AUTO is set to off (manual). Note, when CALL:SETup:TCReconfig:CHANnel:UPLink:CONTrol:AUTO is set to on (auto), the TCR uplink UARFCN used by the test set is determined by CALL:SETup:TCReconfig:CHANnel:DOWNlink .

This setting is only applicable when TCR Channel (UARFCN) State is set to On .

The TCR uplink UARFCN being used by the test set at any given time can be determined by CALL:STATus:SETup:TCReconfig:CHANnel:UPLink[:CHANnel]? .

If the entered TCR Uplink Channel (UARFCN) has an uplink/downlink offset of less than 30 MHz when compared with the TCR Downlink Channel (UARFCN) , the warning message "+217, Performance not specified for UL/DL frequency offset < 30 MHz" will be issued. The setting will be used as entered if not changed by the user.

Setting

Range: see CALL:SETup:TCReconfig:CHANnel:UPLink:CHANnel

Query

*RST Setting

TCR uplink UARFCN = 9780, TCR uplink channel control = on (auto)

Test Application Revision A.11 and above.

Lab Application Revision D.02 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:CHANnel:UPLink 9780"
! Sets the TCR uplink channel UARFCN to 9780 and selects manual control mode
! for TCR uplink channel.

Function

The setting form of this command sets TCR Uplink Channel (UARFCN) to a specific UARFCN.

This setting is only applicable when TCR Channel (UARFCN) State is set to On .

Note, this TCR uplink UARFCN is only used by the test set when CALL:SETup:TCReconfig:CHANnel:UPLink:CONTrol:AUTO is set to off (manual). When CALL:SETup:TCReconfig:CHANnel:UPLink:CONTrol:AUTO is set to on (auto), the TCR uplink UARFCN used by the test set is determined by CALL:SETup:TCReconfig:CHANnel:DOWNlink .

The query form of this command returns the TCR uplink UARFCN that is used by the test set when CALL:SETup:TCReconfig:CHANnel:UPLink:CONTrol:AUTO is set to off (manual).

The TCR uplink UARFCN being used by the test set at any given time can be determined by CALL:STATus:SETup:TCReconfig:CHANnel:UPLink[:CHANnel]? .

If the entered TCR Uplink Channel (UARFCN) has an uplink/downlink offset of less than 30 MHz when compared with the TCR Downlink Channel (UARFCN) , the warning message "+217, Performance not specified for UL/DL frequency offset < 30 MHz" will be issued. The setting will be used as entered if not changed by the user.

Setting

Range:

• 12, 37, 62, 87, 112, 137, 162, 187, 212, 237, 262, 287
• 782, 787, 807, 812, 837, 862
• 937 - 1288, resolution = 1
• 1312 - 1513, resolution = 1
• 1662, 1687, 1712, 1737, 1762, 1787, 1812, 1837, 1862
• 2012 - 2338, resolution = 1
• 2362, 2387, 2412, 2437, 2462, 2487, 2512, 2537, 2562, 2587, 2612, 2637, 2662, 2687
• 2712 - 2863, resolution = 1
• 2887 - 3163, resolution = 1
• 3187, 3212, 3237, 3262, 3287, 3312, 3337, 3362, 3387, 3412, 3437, 3462
• 3487 - 3587, resolution = 1
• 3612 - 3678, resolution = 1
• 3702, 3707, 3732, 3737, 3762, 3767
• 3792 - 3818, resolution = 1
• 3842, 3867
• 3892 - 3918, resolution = 1
• 3942, 3967
• 4132 - 4233, resolution = 1
• 8762 - 8912, resolution = 1
• 9262 - 9538, resolution = 1
• 9612 - 9888, resolution = 1

Query

*RST Setting

Test Application Revision A.11 and above.

Lab Application Revision D.02 and above.

Lab Application Revision: E.00.34 and above, added 3487 - 3587.

Test Application Revision A.14 and Lab Application Revision F.00 and above, added 3612 - 3678, 3702, 3707, 3732, 3737, 3762, 3767, 3792 - 3818, 3842, 3867, 3892 - 3918, 3942, 3967

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:CHANnel:UPLink:CHANnel 9780"
! Sets the TCR uplink channel UARFCN to 9780.

Function

Sets/queries the TCR Uplink Channel (UARFCN) control mode.

This setting is only applicable when TCR Channel (UARFCN) State is set to On .

• Auto - TCR uplink UARFCN is determined by CALL:SETup:TCReconfig:CHANnel:DOWNlink .
• Manual - TCR uplink UARFCN is determined by CALL:SETup:TCReconfig:CHANnel:UPLink:CHANnel .

The TCR uplink UARFCN being used by the test set at any given time can be determined by CALL:STATus:SETup:TCReconfig:CHANnel:UPLink[:CHANnel]? .

Setting

Range:

• 1|ON (auto)
• 0|OFF (manual)

Query

*RST Setting

1 (auto)

Test Application Revision A.11 and above.

Lab Application Revision D.02 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:CHANnel:UPLink:CONTrol:AUTO ON"
! Sets TCR uplink control mode to auto.

Function

Sets/queries TCR DPCH Bc/Bd Control .

Setting

Range: 1|ON|0|OFF

Query

*RST Setting

Test Application Revision: A.09 and above

Lab Application Revision: C.04 and above

Lab Application Revision: D.00 and above

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:DPCHannel:BETA:AUTO OFF"
! Sets TCR DPCH Bc/Bd Control to Manual.

Function

Sets/queries TCR Default DPCH Offset (DOFF) .

This command is only applicable when CALL:HANDoff:TCReconfig:CFNHandling is set to INITialise.

Setting

Range: 0 to 5

Resolution: 1

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above

Lab Application Revision: C.04 and above

Lab Application Revision: D.00 and above

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:DPCHannel:DOFFset 3"
! Sets TCR Default DPCH Offset (DOFF) to 3 x 512 chips.

Function

Sets/queries TCR Manual Uplink DPCH Bc .

This command is only applicable when CALL:SETup:TCReconfig:DPCHannel:BETA:AUTO is set to MANual.

Setting

Range: 1 to 15

Resolution: 1

Query

*RST Setting

Test Application Revision: A.09 and above

Lab Application Revision: C.04 and above

Lab Application Revision: D.00, range is 1 to 15 (but 1 is not recommended)

Lab Application Revision D.01, range is 2 to 15

Test Application Revision A.11 and Lab Application Revisions D.02 and E.00, range is 1 to 15 (vs. 2 to 15)

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:DPCHannel:MANual:CBETa 15"
! Sets TCR Manual Uplink DPCH Bc to 15.

Function

Sets/queries TCR Manual Uplink DPCH Bd .

This command is only applicable when CALL:SETup:TCReconfig:DPCHannel:BETA:AUTO is set to MANual.

Setting

Range: 0 to 15

Resolution: 1

Query

*RST Setting

Test Application Revision: A.09 and above

Lab Application Revision: C.04 and above

Lab Application Revision: D.00 and above

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:DPCHannel:MANual:DBETa 8"
! Sets TCR Manual Uplink DPCH Bd to 8.

Function

Sets/queries TCR Relative DPCH Frame Offset .

This command is only applicable when CALL:HANDoff:TCReconfig:CFNHandling is set to MAINtain.

Setting

Range: -256, 0, 256

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above

Lab Application Revision: C.04 and above

Lab Application Revision: D.00 and above

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:DPCHannel:RFOFfset -256"
! Sets TCR Relative DPCH Frame Offset to -256 chips.

Function

Sets/queries the TCR E-DPCCH/DPCCH Power Offset .

Setting

Range: 0 to 8

Resolution: 1

Query

*RST Setting

0

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:EDPCchannel:POFFset 0" 
! Sets the TCR E-DPCCH/DPCCH Power Offset to 0.

Function

Sets/queries the TCR Reference E-TFCI Power Offsets .

Setting

Range: DEF3410801|DEF3410802|DEF3412101|DEF3412102

Query

*RST Setting

DEF3410802

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:ETFCi:POFFsets:REFerence DEF3410802" 
! Sets the TCR Reference E-TFCI Power Offsets to Def 34108-02.

Function

Sets/queries TCR Number of HARQ Processes .

Setting

Range: 1 to 8

Resolution: 1

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above

Lab Application Revision: C.04 or D.00.04 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:HARQ:PROCess:COUNt 1"
! Sets TCR Number of HARQ Processes to 1.

Function

Sets/queries the TCR Measurement Power Offset .

This parameter can only be set either while the call status is Idle .

This setting only applies when "CALL:SETup:TCReconfig:MPOWer:OFFSet:CONTrol:AUTO" on page 141 is set to OFF (manual).

Setting

Range: -6.0 to +13.0 dB

Resolution: 0.1

Query

Range: -6.0 to +13.0 dB, 9.91E+37

Resolution: 0.5

*RST Setting

Requirements

Lab Application Revision E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:MPOWer -6"
! Sets the TCR Measurement Power Offset to -6 dB.

Function

Sets/queries the automatic control state for the TCR Measurement Power Offset parameter.

ON = automatic

OFF = manual (see "CALL:SETup:TCReconfig:MPOWer[:MOFFset]" on page 139 or "CALL:SETup:TCReconfig:MPOWer:OFFSet:MANual" on page 141 )

This parameter can only be set either while the call status is Idle .

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

*RST Setting

Requirements

Lab Application Revision E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:MPOWer:OFFSet:CONTrol:AUTO 0"
! Sets the TCR Measurement Power Offset control state to manual.

Function

Sets/queries the TCR Measurement Power Offset .

This parameter can only be set either while the call status is Idle .

This setting only applies when "CALL:SETup:TCReconfig:MPOWer:OFFSet:CONTrol:AUTO" on page 141 is set to OFF (manual).

Setting

Range: -6.0 to +13.0 dB

Resolution: 0.5

Query

Range: -6.0 to +13.0 dB, 9.91E+37

Resolution: 0.5

*RST Setting

Requirements

Lab Application Revision E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:MPOWer:OFFSet:MANual -6"
! Sets the TCR Measurement Offset Power to -6 dB.

Function

Sets/queries TCR UE IR Buffer Allocation .

Setting

Range: IMPLicit|EXPLicit

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above

Lab Application Revision: C.04 or D.00.04 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:MS:IREDundancy:BUFFer:ALLocation EXPLicit"
! Sets TCR UE IR Buffer Allocation to Explicit.

Function

Sets/queries TCR Explicit UE IR Buffer Size .

This setting is only applicable when CALL:SETup:TCReconfig:MS:IREDundancy:BUFFer:ALLocation is set to EXPLicit.

Setting

Range: 800, 1600, 2400, 3200, 4000, 4800, 5600, 6400, 7200, 8000, 8800, 9600, 10400, 11200, 12000, 12800, 13600, 14400, 15200, 16000, 17600, 19200, 20800, 22400, 24000, 25600, 27200, 28800, 30400, 32000, 36000, 40000, 44000, 48000, 52000, 56000, 60000, 64000, 68000, 72000, 76000, 80000, 88000, 96000, 104000, 112000, 120000, 128000, 136000, 144000, 152000, 160000, 176000, 192000, 208000, 224000, 240000, 256000, 272000, 288000, 304000

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above

Lab Application Revision: C.04 or D.00.04 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:MS:IREDundancy:BUFFer:SIZe 9600"
! Sets TCR Explicit UE IR Buffer Size to 9600.

Function

Sets/queries the RB Test Mode TCR RAB .

Setting

Range:

• RMC12 (12.2k RMC)
• RMC64 (64k RMC)
• RMC144 (144k RMC)
• RMC384 (384k RMC)
• RMC33NC (33k No Coding RMC)

Query

*RST Setting

Test Application Revision: A.05 and above.

Lab Application Revision: B.01 and above.

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:RBTest:RAB RMC64"
! Sets the handover RB test mode RAB to 64k RMC.

Function

Sets/queries the TCR Absolute Grant .

Setting

Range: ZGRant|INDex0|INDex1|INDex2|INDex3...|INDex37

Query

*RST Setting

IND37

Requirements

Test Application Revision: A.12 and above, with the required feature license

Lab Application Revision: E.00.16 and above

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:SGRant:ABSolute INDex37" 
! Sets the TCR Absolute Grant to 37:6(168)^2.

Function

Setting

Range: 1 to 4

Resolution: 1

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above, with the required feature license

Lab Application Revision: C.04 and above

Lab Application Revision: D.00 and above

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:UPLink:ANACk:RFACtor 3"
! Sets TCR Ack-Nack Repetition Factor to 3.

Function

Setting

Range: 0, 2, 4, 6, 8, 10, 20, 40, 80, 160 ms

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above, with the required feature license

Lab Application Revision: C.04 and above

Lab Application Revision: D.00 and above

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:UPLink:CQI:FCYCle 4MS"
! Sets TCR CQI Feedback Cycle (k) to 4 ms.

Function

Setting

Range: 1 to 4

Resolution: 1

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above, with the required feature license

Lab Application Revision: C.04 and above

Lab Application Revision: D.00 and above

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:UPLink:CQI:RFACtor 2"
! Sets TCR CQI Repetition Factor to 2.

Function

Setting

Range: 0 to 8

Resolution: 1

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above, with the required feature license

Lab Application Revision: C.04 and above

Lab Application Revision: D.00 and above

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:UPLink:DACK 8"
! Sets TCR DeltaACK to 8.

Function

Setting

Range: 0 to 8

Resolution: 1

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above, with the required feature license

Lab Application Revision: C.04 and above

Lab Application Revision: D.00 and above

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:UPLink:DCQI 7"
! Sets TCR DeltaCQI to 7.

Function

Setting

Range: 0 to 8

Resolution: 1

Query

*RST Setting

Requirements

Test Application Revision: A.09 and above, with the required feature license

Lab Application Revision: C.04 and above

Lab Application Revision: D.00 and above

Programming Example

 
OUTPUT 714;"CALL:SETup:TCReconfig:UPLink:DNACk 8"
! Sets TCR DeltaNACK to 8.