CALL:STATus

Last updated: September 2, 2009

NOTE

The CALL:STATus commands are query only. They return values that indicate the test set's actual hardware settings. Actual hardware settings can differ from settings the user has entered, most frequently due to an error condition. When no error conditions exist, the commands used to enter values return the same results as the commands used to query actual hardware settings. For example, "CALL:AWGNoise:POWer?" returns the same value as "CALL:STATus:AWGNoise:POWer?" when no error conditions exist.

GPIB Command Conventions

CALL:STATus[:STATe][:VOICe]?

Function	Queries the status of the call. See Call Connection State .
Query	Range: CALL\|CONN\|HAND\|IDLE\|PAG\|REG\|REL\|SREQ Only IDLE is returned in FDD Test operating mode.
*RST Setting	IDLE
Requirements	Test or Lab Application Revision: A.01 and above Test Application Revision: A.05 and above added CALL Lab Application Revision: B.01 and above added CALL
Programming Example OUTPUT 714;"CALL:STATus?" ! Returns the current call processing state.

CALL:STATus:AICHannel[:CELL][:LEVel]?

Function	Queries the current level of the acquisition indicator channel. This query is not applicable to FDD Test operating mode. See Downlink Code Channel Information .
Query	Range: -20.00 to 0 dB, 9.91 E+37 Resolution: 0.01 dB
*RST Setting	-9.9 dB
Requirements	Test Application Revision: A.02 and above Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:AICHannel?"

CALL:STATus:AICHannel[:CELL]:STATe?

Function	Queries the current state of the acquisition indicator channel. This query is not applicable to FDD Test operating mode. See Downlink Code Channel Information .
Query	Range: 0\|1
*RST Setting	1 (on)
Requirements	Test Application Revision: A.02 and above Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:AICHannel:STATe?"

CALL:STATus[:GMM]:ATTached:STATe?

Function	Queries the attached state of the UE. See GMM State .
Query	Range: ATT - attached ATTINC - attach incomplete DET - detached NONE
*RST Setting	NONE
Requirements	Test Application Revision: A.08.20 and above Lab Application Revision: A.02 and above
Programming Example OUTPUT 714;"CALL:STATus:ATTached:STATe?"

CALL:STATus:AWGNoise[:INTernal]:POWer[:AMPLitude]([:SELected]|:FDD)?

Function	Queries the current power level of the additive white Gaussian noise (AWGN) source. AWGN power level is set using the CALL:AWGNoise commands. The optional [:SELected] mnemonic in this command specifies that the AWGN power level being queried applies to the current system type (FDD is currently the only system type available). See Cell Power and AWGN Power for more information about desired versus current power levels.
Query	Range: -165 dBm/3.84 MHz to +35 dBm/3.84 MHz, NAN (this is the range of settings accepted, see Cell Power, AWGN Power and Total RF Power Ranges for the actual hardware range of the source) 9.91 E+37 (NAN) is returned if CALL:STATus:AWGNoise[:INTernal]:POWer:STATe? is OFF Resolution: 0.01 dB
*RST Setting	9.91 E+37 (NAN)
Requirements	Test or Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:AWGNoise:POWer?" !Queries the current AWGN power.

CALL:STATus:AWGNoise[:INTernal]:POWer:STATe?

Function	Queries the current on/off state of the additive white Gaussian noise (AWGN) source. AWGN power level on/off state is set using the CALL:AWGNoise commands. See Cell Power and AWGN Power for more information about desired versus current power levels.
Query	Range: 1\|0
*RST Setting	0 (off)
Requirements	Test or Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:AWGNoise:POWer:STATe?"

CALL:STATus:CCPChannel:PRIMary[:CELL[1]][:LEVel]?

Function	Queries the current level of the primary common control physical channel. See Downlink Code Channel Information .
Query	Range: -20.00 to 0 dB, 9.91 E+37 Resolution: 0.01 dB
*RST Setting	-5.3 dB
Requirements	Test or Lab Application Revision: A.01 and above. Test Application Revision A.06 changed RST Setting to -5.3 dB. Lab Application Revision C.01 changed RST Setting to -5.3 dB.
Programming Example OUTPUT 714;"CALL:STATus:CCPChannel:PRIMary?"

CALL:STATus:CCPChannel:PRIMary[:CELL[1]]:STATe?

Function	Queries the current state of the primary common control physical channel. See Downlink Code Channel Information .
Query	Range: 0\|1
*RST Setting	1 (on)
Requirements	Test or Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:CCPChannel:PRIMary:STATe?"

CALL:STATus:CCPChannel:PRIMary:CELL2[:LEVel]?

Function	Queries the current level of the cell 2 primary common control physical channel. See Cell 2 Overview and Downlink Code Channel Information .
Query	Range: -20.00 to 0 dB, 9.91 E+37 Resolution: 0.01 dB
*RST Setting	9.91E+37
Requirements	Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:CCPChannel:PRIMary:CELL2?"

CALL:STATus:CCPChannel:PRIMary:CELL2:STATe?

Function	Queries the current state of the cell 2 primary common control physical channel. See Cell 2 Overview and Downlink Code Channel Information .
Query	Range: 0\|1
*RST Setting	0 (off)
Requirements	Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:CCPChannel:PRIMary:CELL2:STATe?"

CALL:STATus:CCPChannel:SECondary[:CELL][:LEVel]?

Function	Queries the current level of the secondary common control physical channel. See Downlink Code Channel Information .
Query	Range: -20.00 to 0 dB, 9.91 E+37 Resolution: 0.01 dB
*RST Setting	-10.3 dB
Requirements	Test Application Revision: A.02 and above Lab Application Revision: A.01 and above Test Application Revision A.06 changed RST Setting to -10.3 dB. Lab Application Revision C.01 changed RST Setting to -10.3 dB.
Programming Example OUTPUT 714;"CALL:STATus:CCPChannel:SECondary?"

CALL:STATus:CCPChannel:SECondary[:CELL]:STATe?

Function	Queries the current state of the secondary common control physical channel. See Downlink Code Channel Information .
Query	Range: 0\|1
*RST Setting	1 (on)
Requirements	Test Application Revision: A.02 and above Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:CCPChannel:SECondary:STATe?"

CALL:STATus:CELL[1]:POWer[:AMPLitude]?

Function	Queries the current cell power level. Cell power is set using the CALL:POWer commands. See Cell Power and AWGN Power for more information about desired versus current power levels.
Query	Range: -165 dBm/3.84 MHz to +37 dBm/3.84 MHz, NAN (this is the range of settings accepted, see Cell Power, AWGN Power and Total RF Power Ranges for the actual hardware range of the source) 9.91 E+37 (NAN) is returned if CALL:STATus:CELL[1]:POWer:STATe? is OFF Resolution: 0.01 dB
*RST Setting	-75.00 dBm
Requirements	Test or Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:CELL:POWer:AMPLitude?"

CALL:STATus:CELL[1]:POWer:STATe?

Function	Queries the current state of the cell power setting. Cell power state is set using the CALL:POWer commands. See Cell Power and AWGN Power for more information about desired versus current power levels.
Query	Range: 1\|0
*RST Setting	1 (on)
Requirements	Test or Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:CELL:POWer:STATe?"

CALL:STATus:CELL:SYSTem[:TYPE]?

Function	Queries the current system type that the test set is currently emulating. When the test set is in active cell operating mode (see CALL:OPERating ) the current system type is selected by the CALL:SYSTem command. (Active cell operating mode is not available in the initial W-CDMA test application release.) When the test set is in any test mode operating mode (see CALL:OPERating ) or CW operating mode, this command will return the corresponding system type.
Query	Range: FDD\|CW
*RST Setting	FDD
Requirements	Test or Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:CELL:SYSTem?"

CALL:STATus:CELL2:POWer[:AMPLitude]?

Function	Queries the current cell 2 power level. (See Cell 2 Overview ).
Query	Range: -165 dBm/3.84 MHz to +37dBm/3.84 MHz, 9.91 E+37 (-115 dBm/3.84 MHz to -13 dBm/3.84 MHz actual hardware range with amplitude offset = 0) The actual power range is defined by adding the value of the associated amplitude offset to the range above. For example, if amplitude offset is -3.5 dB, then the power range will be -118.5 dBm/3.84 MHz to -16.5 dBm/3.84 MHz. Resolution: 0.01 dBm/3.84 MHz
*RST Setting	9.91E+37
Requirements	Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:CELL2:POWer?"

CALL:STATus:CELL2:POWer:STATe?

Function	Queries the current state of the cell 2 power setting. (See Cell 2 Overview ).
Query	Range: 1\|0
*RST Setting	0 (off)
Requirements	Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:CELL2:POWer:STATe?"

CALL:STATus:COMPressed:STATe?

Function	Queries`Compressed Mode State/Overall CM` (see Enabling/Disabling Compressed Mode ).
Query	Range: 1\|0
*RST Setting	0 (off)
Requirements	Lab Application Revision: B.01 and above
Programming Example OUTPUT 714;"CALL:STATus:COMPressed:STATe?"

CALL:STATus:COMPressed:TGPSequence:ALL:STATe?

Function	Queries which TGPSs are currently active. The first num value corresponds to the`First TGPS` , the second num value corresponds to the`Second TGPS` , etc. See Enabling/Disabling Compressed Mode .
Query	Range: 1\|0
*RST Setting	0, 0, 0, 0
Requirements	Lab Application Revision: D.00.04 and above
Programming Example OUTPUT 714;"CALL:STATus:COMPressed:TGPSequence:ALL:STATe?"

CALL:STATus:CPC:DRX:ACTivated?

Function	Queries the Current DRX Activated State.
Query	Range: 1\|0
*RST Setting	0 (off)
Requirements	Lab Application Revision: F.00.19 and above
Programming Example OUTPUT 714;"CALL:STATus:CPC:DRX:ACTivated?"

CALL:STATus:CPC:DTX:ACTivated?

Function	Queries the current DTX Activated State.
Query	Range: 1\|0
*RST Setting	0 (off)
Requirements	Lab Application Revision: F.00.19 and above
Programming Example OUTPUT 714;"CALL:STATus:CPC:DTX:ACTivated?"

CALL:STATus:CPC:DTX:TRANsition:C1Cycle2:COUNt?

Function	Queries the number of DTX Cycle 1 to Cycle 2 transitions.
Query	Range: 0 to 150,000, 9.91 E+37 Resolution: 0.01
*RST Setting	9.91 E+37
Requirements	Lab Application Revision: F.00.19 and above
Programming Example OUTPUT 714;"CALL:STATus:CPC:DTX:TRANsition:C1Cycle2:COUNt?"

CALL:STATus:CPC:HLESs:ACTivated?

Function	Queries the Current HS-SCCH-less Activated State.
Query	Range: 1\|0
*RST Setting	0 (off)
Requirements	Lab Application Revision: F.01 and above
Programming Example OUTPUT 714;"CALL:STATus:CPC:HLESs:ACTivated?"

CALL:STATus:CPC:HLESs:TBSize?

Function	Queries the TB size that is being used for HS-SCCH-less operation.
Query	Range: 137 to 1483 bits, 9.91 E+37 Resolution: 0.01
*RST Setting	9.91 E+37
Requirements	Lab Application Revision: F.01 and above
Programming Example OUTPUT 714;"CALL:STATus:CPC:HLESs:TBSize?"

CALL:STATus:CPC:MS:DPCChannel:BURSt[1]:COUNt?

Function	Queries the Number of DPCCH Burst 1 Transmissions.
Query	Range: 0 to 150,000, 9.91 E+37 Resolution: 0.01
*RST Setting	9.91 E+37
Requirements	Lab Application Revision: F.00.19 and above
Programming Example OUTPUT 714;"CALL:STATus:CPC:MS:DPCChannel:BURSt:COUNt?"

CALL:STATus:CPC:MS:DPCChannel:BURSt2:COUNt?

Function	Queries the Number of DPCCH Burst 2 Transmissions.
Query	Range: 0 to 150,000, 9.91 E+37 Resolution: 0.01
*RST Setting	9.91 E+37
Requirements	Lab Application Revision: F.00.19 and above
Programming Example OUTPUT 714;"CALL:STATus:CPC:MS:DPCChannel:BURSt2:COUNt?"

CALL:STATus:CPC:MS:DRX:CONFigured?

Function	Queries whether the DL DRX configuration has been successfully configured in the UE. This result is only available in Active Cell mode.
Query	Range: 1\|0
*RST Setting	0 (false)
Requirements	Lab Application Revision: F.00.19 and above
Programming Example OUTPUT 714;"CALL:STATus:CPC:MS:DRX:CONFigured?"

CALL:STATus:CPC:MS:DTX:CONFigured?

Function	Queries whether UL DTX configuration has been successfully configured in the UE.
Query	Range: 1\|0
*RST Setting	0 (false)
Requirements	Lab Application Revision: F.00.19 and above
Programming Example OUTPUT 714;"CALL:STATus:CPC:MS:DTX:CONFigured?"

CALL:STATus:CPC:MS:HLESs:CONFigured?

Function	Queries whether HS-SCCH-less configuration has been successfully configured in the UE..
Query	Range: 1\|0
*RST Setting	0 (false)
Requirements	Lab Application Revision: F.01 and above
Programming Example OUTPUT 714;"CALL:STATus:CPC:MS:HLESs:CONFigured?"

CALL:STATus:CPIChannel[:CELL[1]][:LEVel]?

Function	Queries the current common pilot channel's power. See Downlink Code Channel Information .
Query	Range: -20.00 to 0 dB, 9.91 E+37 Resolution: 0.01 dB
*RST Setting	-3.3 dB
Requirements	Test or Lab Application Revision: A.01 and above Test Application Revision A.06 changed RST Setting to -3.3 dB. Lab Application Revision C.01 changed RST Setting to -3.3 dB.
Programming Example OUTPUT 714;"CALL:STATus:CPIChannel?"

CALL:STATus:CPIChannel[:CELL[1]]:POWer[:AMPLitude]?

Function	Queries the current cell1 CPICH power level in dBm (current Cell Power + current CPICH level). See Downlink Code Channel Information .
Query	Range: -165.00 dBm to +37.00 dBm, 9.91 E+37 Resolution: 0.01 dB
*RST Setting	-78.3 dBm
Requirements	Test or Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:CPIChannel:POWer?"

CALL:STATus:CPIChannel[:CELL[1]]:STATe?

Function	Queries the current state of the common pilot channel. See Downlink Code Channel Information .
Query	Range: 1\|0
*RST Setting	1 (on)
Requirements	Test or Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:CPIChannel:STATe?"

CALL:STATus:CPIChannel:CELL2[:LEVel]?

Function	Queries the current cell 2 common pilot channel's power. See Cell 2 Overview and Downlink Code Channel Information .
Query	Range: -20.00 to 0 dB, 9.91 E+37 Resolution: 0.01 dB
*RST Setting	9.91E+37
Requirements	Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:CPIChannel:CELL2?"

CALL:STATus:CPIChannel:CELL2:POWer[:AMPLitude]?

Function	Queries the current cell2 CPICH power level in dBm (current Cell 2 Power + current Cell 2 CPICH level). See Cell 2 Overview and Downlink Code Channel Information .
Query	Range: -165.00 dBm to +37.00 dBm, 9.91 E+37 Resolution: 0.01 dB
*RST Setting	9.91 E+37
Requirements	Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:CPIChannel:CELL2:POWer?"

CALL:STATus:CPIChannel:CELL2:STATe?

Function	Queries the current state of the cell 2 common pilot channel. See Cell 2 Overview and Downlink Code Channel Information .
Query	Range: 1\|0
*RST Setting	0 (off)
Requirements	Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:CPIChannel:CELL2:STATe?"

CALL:STATus[:STATe]:DATA?

Function	Queries the status of the data connection. See Data Connection State .
Query	Range: ATTG\|DET\|IDLE\|OFF\|PDPAG\|PDP\|PDPD
*RST Setting	OFF
Requirements	Test Application Revision: A.03 and above Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:DATA?" ! Returns the current data connection state.

CALL:STATus:DPCHannel[:LEVel]?

Function	Queries the current dedicated physical channel's power. See Downlink Code Channel Information .
Query	Range: -20.00 to 0 dB, 9.91 E+37 Resolution: 0.01 dB
*RST Setting	9.91 E+37
Requirements	Test or Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:DPCHannel?"

CALL:STATus:DPCHannel:STATe?

Function	Queries the current state of the dedicated physical channel. See Downlink Code Channel Information .
Query	Range: 1\|0
*RST Setting	0 (off)
Requirements	Test or Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:DPCHannel:STATe?"

CALL:STATus:DPCHannel:CELL2[:LEVel]?

Function	Queries the current cell 2 dedicated physical channel's power. See Cell 2 Overview and Downlink Code Channel Information .
Query	Range: -20.00 to 0 dB, 9.91 E+37 Resolution: 0.01 dB
*RST Setting	9.91 E+37
Requirements	Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:DPCHannel:CELL2?"

CALL:STATus:DPCHannel:CELL2:STATe?

Function	Queries the current state of the cell 2 dedicated physical channel. See Cell 2 Overview and Downlink Code Channel Information .
Query	Range: 1\|0
*RST Setting	0 (off)
Requirements	Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:DPCHannel:CELL2:STATe?"

CALL:STATus:DPCHannel[:CELL]:CURCbeta?

Function	Queries the current power gain of the dedicated physical control channel (DPCCH) see Uplink DPCH Bc/Bd Control .
Query	Range: 1 to 15 Resolution: 1
*RST Setting	8
Requirements	Test Application Revision: A.03 and above Lab Application Revision: A.01 and above Test Application Revision A.11 and Lab Application Revisions D.02 and E.00, range is 1 to 15 (vs. 2 to 15)
Programming Example OUTPUT 714;"CALL:STATus:DPCHannel:CURCbeta?"

CALL:STATus:DPCHannel[:CELL]:CURDbeta?

Function	Queries the current power gain of the dedicated physical data channel (DPDCH) see Uplink DPCH Bc/Bd Control .
Query	Range: 0 to 15 Resolution: 1
*RST Setting	15
Requirements	Test Application Revision: A.03 and above Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:DPCHannel:CURDbeta?"

CALL:STATus:DPCHannel:OFFSet?

Function	Queries the Current DPCH Offset .
Query	Range: 0 to 2560 Resolution: 256
*RST Setting	0 chips
Requirements	Test Application Revision: A.09 and above Lab Application Revision: C.04 and above Lab Application Revision: D.00 and above
Programming Example OUTPUT 714;"CALL:STATus:DPCHannel:OFFSet?"

CALL:STATus:EAGChannel[:CELL][:LEVel]?

Function	Queries the current level of the E-AGCH. See Downlink Code Channel Information .
Query	Range: -20.00 dB to 0.00 dB, 9.91E+37 Resolution: 0.01 dB
*RST Setting	9.91E+37
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:STATus:EAGChannel?"

CALL:STATus:EAGChannel[:CELL]:STATe?

Function	Queries the current state of the E-AGCH. See Downlink Code Channel Information .
Query	Range: 1\|0
*RST Setting	0 (off)
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:STATus:EAGChannel:STATe?"

CALL:STATus:EDCHannel[:CELL]:BLOCk:SIZE[:LAST]?

Function	Queries the Last Block Size .
Query	Range: 0 to 20000 bits, 9.91E+37 Resolution: 1 bit
*RST Setting	9.91E+37
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:STATus:EDCHannel:BLOCk:SIZE?"

CALL:STATus:EDCHannel[:CELL]:BLOCk:SIZE:AVERage?

Function	Queries the Avg Block Size .
Query	Range: 0 to 20000 bits, 9.91E+37 Resolution: 1 bit
*RST Setting	9.91E+37
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:STATus:EDCHannel:BLOCk:SIZE:AVERage?"

CALL:STATus:EDCHannel[:CELL]:BLOCk:SIZE:MAXimum?

Function	Queries the Max Block Size .
Query	Range: 0 to 20000 bits, 9.91E+37 Resolution: 1 bit
*RST Setting	9.91E+37
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:STATus:EDCHannel:BLOCk:SIZE:MAXimum?"

CALL:STATus:EDCHannel[:CELL]:BLOCk:SIZE:MINimum?

Function	Queries the Min Block Size .
Query	Range: 0 to 20000 bits, 9.91E+37 Resolution: 1 bit
*RST Setting	9.91E+37
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:STATus:EDCHannel:BLOCk:SIZE:MINimum?"

CALL:STATus:EDCHannel[:CELL]:IBTHroughput?

Function	Queries the Throughput .
Query	Range: 0 to 5760 kbps, 9.91E+37 Resolution: 1 kbps
*RST Setting	9.91E+37
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:STATus:EDCHannel:IBTHroughput?"

CALL:STATus:EHIChannel[:CELL][:LEVel]?

Function	Queries the current level of the E-HICH. See Downlink Code Channel Information .
Query	Range: -20.00 dB to 0.00 dB, 9.91E+37 Resolution: 0.01 dB
*RST Setting	9.91E+37
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:STATus:EHIChannel?"

CALL:STATus:EHIChannel[:CELL]:STATe?

Function	Queries the current state of the E-HICH. See Downlink Code Channel Information .
Query	Range: 1\|0
*RST Setting	0 (off)
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:STATus:EHIChannel:STATe?"

CALL:STATus:EHIChannel[:CELL]:ACK[:COUNt]?

Function	Queries the ACKs Transmitted .
Query	Range: 0 to 150000, 9.91E+37 Resolution: 1
*RST Setting	9.91E+37
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:STATus:EHIChannel:ACK?"

CALL:STATus:EHIChannel[:CELL]:NACK[:COUNt]?

Function	Queries the ACKs Transmitted .
Query	Range: 0 to 150000, 9.91E+37 Resolution: 1
*RST Setting	9.91E+37
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:STATus:EHIChannel:NACK?"

CALL:STATus:ERGChannel[:CELL][:LEVel]?

Function	Queries the current level of the E-RGCH. See Downlink Code Channel Information .
Query	Range: -20.00 dB to 0.00 dB, 9.91E+37 Resolution: 0.01 dB
*RST Setting	9.91E+37
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:STATus:ERGChannel?"

CALL:STATus:ERGChannel[:CELL]:STATe?

Function	Queries the current state of the E-RGCH. See Downlink Code Channel Information .
Query	Range: 1\|0
*RST Setting	0 (off)
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:STATus:ERGChannel:STATe?"

CALL:STATus:ETFCi[:LAST]?

Function	Queries the Last Received E-TFCI .
Query	Range: 0 to 127, 9.91E+37 Resolution: 1
*RST Setting	9.91E+37
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:STATus:ETFCi?"

CALL:STATus:ETFCi:RECord[:STATe]?

Function	Queries the E-TFCI Recording State .
Query	Range: REC(recording)\|IDLE
*RST Setting	IDLE
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:STATus:ETFCi:RECord?"

CALL:STATus:ETFCi:RECord:ALL?

Function	Queries the Recorded E-TFCI Values . This result always returns 50 comma-separated numbers; Number of E-TFCI Results Recorded E-TFCI values, followed by NANs (9.91E+37).
Query	Range: 0 to 127, 9.91E+37 Resolution: 1
*RST Setting	9.91E+37
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:STATus:ETFCi:RECord:ALL?"

CALL:STATus:ETFCi:RECord:COUNt?

Function	Queries the Number of E-TFCI Results Recorded .
Query	Range: 0 to 50 Resolution: 1
*RST Setting	0
Requirements	Test Application Revision: A.12 and above, with the required feature license Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:STATus:ETFCi:RECord:COUNt?"

CALL:STATus:ETFCi:RECord:FRAMe:INDicator?

Function	Queries the Recorded E-TFCI Integrity Indicators.
Query	Range: An array of 50 values, each element of the array has the following range: - NONE (No value recorded) - GCRC (Good CRC) - BCRC (Bad CRC) - DTX (EDPDCH subframe is DTX'd for an E-DCH TTI transmission)
*RST Setting	NONE (No value recorded)
Requirements	Lab Application Revision: E.00.34 and above
Programming Example OUTPUT 714;"CALL:STATus:ETFCi:RECord:FRAMe:INDicator?"

CALL:STATus:FBINdicator?

Function	Queries the Current Info, Frequency Band .
Query	Range: BAND1\|BAND2\|BAND3\|BAND4\|BAND5\|BAND6\|BAND7\|BAND8\|BAND9\|BAND10\| BAND11\|BAND12\|BAND13\|BAND14
*RST Setting	BAND1
Requirements	Test Application Revision: A.08 and above. Test Application Revision A.09, added BAND8 and BAND9. Lab Application Revision: C.03 and above. Lab Application Revision C.04 and D.00, added BAND8 and BAND9. Test Application Revision A.10.01 and Lab Application Revision D.01.01 added BAND7 Test Application Revision A.11 and Lab Application Revisions D.02 and E.00, added BAND10 Test Application Revision A.13 and Lab Application Revision E.00.34, added BAND11 Test Application Revision A.14 and Lab Application Revision F.00, added BAND12, BAND13, BAND14
Programming Example OUTPUT 714;"CALL:STATus:FBINdicator?"

CALL:STATus:HSDSchannel:TBSize?

Function	Queries the Current Test Mode Transport Block Size .
Query	Range: 120 to 42192 Resolution: 1
Requirements	Test Application Revision: A.09 and above, with the required feature license Lab Application Revision: C.04 and above Lab Application Revision: D.00 and above Test Application Revision A.14 and Lab Application Revision F.00 and above, range extended.
Programming Example OUTPUT 714;"CALL:STATus:HSDSchannel:TBSize?"

CALL:STATus:HSDSchannel:TBSize:PSData?

Function	Queries the Current Test Mode Transport Block Size .
Query	Range: 137 to 27952 Resolution: 1
*RST Setting	4664
Requirements	Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:STATus:HSDSchannel:TBSize:PSData?"

CALL:STATus:HSPDschannel[:CELL][:LEVel]?

Function	Queries the current sum of the powers in all of the active HS-PDSCH channels. See Downlink Code Channel Information .
Query	Range: -20.00 to 0 dB, 9.91 E+37 Resolution: 0.01 dB
*RST Setting	9.91 E+37
Requirements	Test Application Revision A.08 and above, with the required feature license Lab Application Revision: C.03 and above.
Programming Example OUTPUT 714;"CALL:STATus:HSPDschannel?"

CALL:STATus:HSPDschannel[:CELL]:STATe?

Function	Queries the current state of the HS-PDSCH channels. See Downlink Code Channel Information .
Query	Range: 1 (on) - power is present in one or more HS-PDSCHs 0 (off) - no power is present in any HS-PDSCH
*RST Setting	0 (off)
Requirements	Test Application Revision A.08 and above, with the required feature license Lab Application Revision: C.03 and above.
Programming Example OUTPUT 714;"CALL:STATus:HSPDschannel:STATe?"

CALL:STATus:HSSCchannel[1][:CELL][:LEVel]?

Function	Queries the current HS-SCCH 1 power level. See Downlink Code Channel Information .
Query	Range: -20.00 to 0 dB, 9.91 E+37 Resolution: 0.01 dB
*RST Setting	9.91 E+37
Requirements	Test Application Revision A.08 and above, with the required feature license Lab Application Revision: C.03 and above.
Programming Example OUTPUT 714;"CALL:STATus:HSSCchannel?"

CALL:STATus:HSSCchannel[1][:CELL]:STATe?

Function	Queries the current state of the HS-SCCH 1 channel. See Downlink Code Channel Information .
Query	Range: 1\|0
*RST Setting	0 (off)
Requirements	Test Application Revision A.08 and above, with the required feature license Lab Application Revision: C.03 and above.
Programming Example OUTPUT 714;"CALL:STATus:HSSCchannel:STATe?"

CALL:STATus:HSSCchannel2[:CELL][:LEVel]?

Function	Queries the current HS-SCCH 2 power level. See Downlink Code Channel Information .
Query	Range: -20.00 to 0 dB, 9.91 E+37 Resolution: 0.01 dB
*RST Setting	9.91 E+37
Requirements	Test Application Revision A.08 and above, with the required feature license Lab Application Revision: C.03 and above.
Programming Example OUTPUT 714;"CALL:STATus:HSSCchannel2?"

CALL:STATus:HSSCchannel2[:CELL]:STATe?

Function	Queries the current state of the HS-SCCH 2 channel. See Downlink Code Channel Information .
Query	Range: 1\|0
*RST Setting	0 (off)
Requirements	Test Application Revision A.08 and above, with the required feature license Lab Application Revision: C.03 and above.
Programming Example OUTPUT 714;"CALL:STATus:HSSCchannel2:STATe?"

CALL:STATus:HSSCchannel3[:CELL][:LEVel]?

Function	Queries the current HS-SCCH 3 power level. See Downlink Code Channel Information .
Query	Range: -20.00 to 0 dB, 9.91 E+37 Resolution: 0.01 dB
*RST Setting	9.91 E+37
Requirements	Test Application Revision A.08 and above, with the required feature license Lab Application Revision: C.03 and above.
Programming Example OUTPUT 714;"CALL:STATus:HSSCchannel3?"

CALL:STATus:HSSCchannel3[:CELL]:STATe?

Function	Queries the current state of the HS-SCCH 3 channel. See Downlink Code Channel Information .
Query	Range: 1\|0
*RST Setting	0 (off)
Requirements	Test Application Revision A.08 and above, with the required feature license Lab Application Revision: C.03 and above.
Programming Example OUTPUT 714;"CALL:STATus:HSSCchannel3:STATe?"

CALL:STATus:HSSCchannel4[:CELL][:LEVel]?

Function	Queries the current HS-SCCH 4 power level. See Downlink Code Channel Information .
Query	Range: -20.00 to 0 dB, 9.91 E+37 Resolution: 0.01 dB
*RST Setting	9.91 E+37
Requirements	Test Application Revision A.08 and above, with the required feature license Lab Application Revision: C.03 and above.
Programming Example OUTPUT 714;"CALL:STATus:HSSCchannel4?"

CALL:STATus:HSSCchannel4[:CELL]:STATe?

Function	Queries the current state of the HS-SCCH 4 channel. See Downlink Code Channel Information .
Query	Range: 1\|0
*RST Setting	0 (off)
Requirements	Test Application Revision A.08 and above, with the required feature license Lab Application Revision: C.03 and above.
Programming Example OUTPUT 714;"CALL:STATus:HSSCchannel4:STATe?"

CALL:STATus:MAXimum:ALLowed:CQI:VALue?

Function	Queries the Maximum Allowed CQI Value.
Query	Range: 0 to 30, 9.91 E+37 Resolution: 1
*RST Setting	9.91 E+37
Requirements	Lab Application Revision: F.00 and above
Programming Example OUTPUT 714;"CALL:STATus:MAXimum:ALLowed:CQI:VALue?"

CALL:STATus:MCELl?

Function	Queries Multi-Cell UTRAN Status.
Query	Range: NONE \| MAIN \| MLOC \| MEXT \| MSHO \| AUX \| AACT
*RST Setting	NONE
Requirements	Lab Application Revision: F.01 and above.
Programming Example OUTPUT 714;"CALL:STATus:MCELl?"

CALL:STATus:MM?

Function	Queries MM Status .
Query	Range: MMSTATUS1 (Updated (Normal)) MMSTATUS2 (Updated (Periodic)) MMSTATUS3 (IMSI Attached) MMSTATUS4 (IMSI Detached) MMSTATUS5 (None)
*RST Setting	MMSTATUS5
Requirements	Test Application Revision: A.05 and above. Lab Application Revision: B.01 and above.
Programming Example OUTPUT 714;"CALL:STATus:MM?"

CALL:STATus:MPOWer:OFFSet:SIGNaled?

Function	Queries the Last Signaled Measurement Power Offset .
Query	Range: -6.0 to +13.0 9.91E+37
*RST Setting	9.91E+37
Requirements	Lab Application Revision: E.00.16 and above
Programming Example OUTPUT 714;"CALL:STATus:MPOWer:OFFSet:SIGNaled?"

CALL:STATus:MS:HSDSchannel:CATegory?

Function	Queries Current UE HS-DSCH Category .
Query	Range: 1-14, 17, 18, 9.91E+37
*RST Setting	9.91E+37
Requirements	Test Application Revision: A.09 and above, with the required feature license Lab Application Revision: C.04 and above Lab Application Revision: D.00 and above Test Application Revision A.10 and Lab Application Revision D.01 added UE categories 7 and 8 Lab Application Revision F.00.07 expanded range from "1-8, 11, 12" to "1-14, 17, 18"
Programming Example OUTPUT 714;"CALL:STATus:MS:HSDSchannel:CATegory?"

CALL:STATus:OCNSource[:CELL][:LEVel]([:SELected]|:FDD)?

Function	Queries the orthogonal channel noise source (OCNS) level for the selected system type. See Downlink Code Channel Information . The OCNS level is set using the CALL:OCNSource commands. The optional [:SELected] keyword in this command specifies that the OCNS channel level being queried applies to the current system type.
Query	Range: 0 to -20 dB, 9.91 E+37 Resolution: 0.01 dB
*RST Setting	9.91 E+37
Requirements	Test or Lab Application Revision: A.01 and above Test Application Revision A.06 changed RST Setting to 9.91 E+37. Lab Application Revision C.01 changed RST Setting to 9.91 E+37.
Programming Example OUTPUT 714;"CALL:STATus:OCNSource?"

CALL:STATus:OCNSource[:CELL]:STATe([:SELected]|:FDD)?

Function	Queries the current on/off state of the orthogonal channel noise simulator channel (OCNS). See Downlink Code Channel Information . The OCNS channel on/off state is set using the CALL:OCNSource commands. The optional [:SELected] keyword in this command specifies that the OCNS channel state being queried applies to the current system type.
Query	Range: 1\|0
*RST Setting	1 (on)
Requirements	Test or Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:OCNSource:STATe?"

CALL:STATus:OCNSource:CELL2[:LEVel]([:SELected]|:FDD)?

Function	Queries the cell 2 orthogonal channel noise source (OCNS) level for the selected system type. See Downlink Code Channel Information . The OCNS level is set using the CALL:CELL2:OCNSource commands. The optional [:SELected] keyword in this command specifies that the OCNS channel level being queried applies to the current system type. (See Cell 2 Overview ).
Query	Range: 0 to -20 dB, 9.91 E+37 Resolution: 0.01 dB
*RST Setting	9.91E+37
Requirements	Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:OCNSource:CELL2?"

CALL:STATus:OCNSource:CELL2:STATe([:SELected]|:FDD)?

Function	Queries the current cell 2 on/off state of the orthogonal channel noise simulator channel (OCNS). See Downlink Code Channel Information . The OCNS channel on/off state is set using the CALL:CELL2:OCNSource commands. The optional [:SELected] keyword in this command specifies that the OCNS channel state being queried applies to the current system type. (See Cell 2 Overview ).
Query	Range: 1\|0
*RST Setting	0 (off)
Requirements	Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:OCNSource:CELL2:STATe?"

CALL:STATus:PICHannel[:CELL][:LEVel]?

Function	Queries the current downlink page indicator channel's power. See Downlink Code Channel Information .
Query	Range: -20.00 to 0 dB, 9.91 E+37 Resolution: 0.01 dB
*RST Setting	-8.3 dB
Requirements	Test or Lab Application Revision: A.01 and above Test Application Revision A.06 changed RST Setting to -8.3 dB. Lab Application Revision C.01 changed RST Setting to -8.3 dB.
Programming Example OUTPUT 714;"CALL:STATus:PICHannel?"

CALL:STATus:PICHannel[:CELL]:STATe?

Function	Queries the current state of the downlink page indicator channel. See Downlink Code Channel Information .
Query	Range: 1\|0
*RST Setting	1 (on)
Requirements	Test or Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:PICHannel:STATe?"

CALL:STATus:PRAChannel[:CELL]:CURCbeta?

Function	Queries the current power gain for the control data of the message portion of the uplink physical random access channel (PRACH) see PRACH Bc/Bd Control .
Query	Range: 2 to 15 Resolution: 1
*RST Setting	15
Requirements	Test Application Revision: A.03 and above Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:PRAChannel:CURCbeta?"

CALL:STATus:PRAChannel[:CELL]:CURDbeta?

Function	Queries the current power gain for the message data of the message portion of the uplink physical random access channel (PRACH) see PRACH Bc/Bd Control .
Query	Range: 0 to 15 Resolution: 1
*RST Setting	15
Requirements	Test Application Revision: A.03 and above Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:PRAChannel:CURDbeta?"

CALL:STATus:REPorted:CQI:LIMitation:COUNt?

Function	Queries the Count of Reported CQI Limitations. This result counts how many times the Maximum Allowed CQI Value is used instead of using reported CQI to avoid code collision.
Query	Range: 0 to 1,500,000, 9.91 E+37 Resolution: 1
*RST Setting	9.91 E+37
Requirements	Lab Application Revision: F.00 and above
Programming Example OUTPUT 714;"CALL:STATus:REPorted:CQI:LIMitation:COUNt?"

CALL:STATus:ROHC:DOWNlink:CID:LARGe?

Function	Queries the Current Downlink ROHC Large CIDs. This result is inferred from the "Current Downlink ROHC Max CID". If the "Current Downlink ROHC Max CID" is greater than 15, then this result is "True", otherwise this result is "False".
Query	Range: 1\|0
*RST Setting	0
Requirements	Lab Application Revision: F.00.19 and above
Programming Example OUTPUT 714;"CALL:STATus:ROHC:DOWNlink:CID:LARGe?"

CALL:STATus:ROHC:DOWNlink:CID:MAXimum?

Function	Queries the Current Downlink ROHC Max CID.
Query	Range: 1 to 16383 Resolution: 1
*RST Setting	15
Requirements	Lab Application Revision: F.00.19 and above
Programming Example OUTPUT 714;"CALL:STATus:ROHC:DOWNlink:CID:MAXimum?"

CALL:STATus:ROHC:DOWNlink:RDDepth?

Function	Queries the Current Downlink Reverse Decompression Depth.
Query	Range: 0 to 65535 Resolution: 1
*RST Setting	0
Requirements	Lab Application Revision: F.00.19 and above
Programming Example OUTPUT 714;"CALL:STATus:ROHC:DOWNlink:RDDepth?"

CALL:STATus:ROHC:UPLink:CID:LARGe?

Function	Queries the Current Uplink ROHC Large CIDs. This result is inferred from the "Current Uplink ROHC Max CID". If the "Current Uplink ROHC Max CID" is greater than 15, then this result is "True", otherwise this result is "False".
Query	Range: 1\|0
*RST Setting	0
Requirements	Lab Application Revision: F.00.19 and above
Programming Example OUTPUT 714;"CALL:STATus:ROHC:UPLink:CID:LARGe?"

CALL:STATus:ROHC:UPLink:CID:MAXimum?

Function	Queries the Current Uplink ROHC Max CID.
Query	Range: 1 to 16383 Resolution: 1
*RST Setting	15
Requirements	Lab Application Revision: F.00.19 and above
Programming Example OUTPUT 714;"CALL:STATus:REPorted:CQI:LIMitation:COUNt?"

CALL:STATus:RRC:STATe?

Function	Queries RRC State .
Query	Range: DCH\|FACH\|IDLE
*RST Setting	IDLE
Requirements	Lab Application Revision: B.01 and above.
Programming Example OUTPUT 714;"CALL:STATus:RRC:STATe?"

CALL:STATus:SERVice:TYPe?

Function	Queries the Current Service Type . The current service type will be set to NONE when an event occurs that causes the service to be stopped. These events include: End Call A call processing error that results in a dropped call UE initiated end of service Full or Partial Preset
Query	Range: AMR: AMR Voice AHSP: AMR Voice + PS Data - HSPA (only applicable to the lab application) APSD: AMR +PS Data (only applicable to the lab application) CSDA: CS Data - Async ( only applicable to the lab application ) CSDV: CS Data - Video Call ( only applicable to the lab application and to a test application with the required feature license ) GPRS: UMTS/GPRS Packet Data ( only applicable to the lab application ) PHSP: UMTS/GPRS Packet Data - HSPA ( only applicable to the lab application ) PSDH: UMTS/GPRS Packet Data - HSDPA ( only applicable to the lab application ) RBT: RB Test Mode RBTH: RB Test Mode - HSDPA ( only applicable to the lab application and to a test application with the required feature license ) RHSP: RB Test Mode - HSPA ( only applicable to the test application with the required feature license ) MMC: Mobile Management connection ( only applicable to the lab application ) NONE
*RST Setting	NONE
Requirements	Test Application Revision: A.01 and above Test Application Revision A.04 added AMR Test Application Revision A.06 with the required feature license, added CSDV Test Application Revision A.08.20 added RBTH Test Application Revision A.12 with the required feature license and Lab Application Revision E.00.16, added RHSP Lab Application Revision: A.01 and above Lab Application Revision A.02 added AMR Lab Application Revision C.01 added CSDV Lab Application Revision C.03 added RBTH Lab Application Revision D.00 added PSDH Lab Application Revision E.00.16 added APSD Lab Application Revision U.00.13 added PHSP Lab Application Revision U.00.31 added AHSP Lab Application Revision F.00 and above added MMC
Programming Example OUTPUT 714;"CALL:STATus:SERVice:TYPe?" ! Returns the current service type.

CALL:STATus:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>UPLink[:CHANnel]?

Function	Queries PCR Info, UL: Channel and Frequency .
Query	Range: see CALL:SETup[:PCReconfig]:CHANnel<[:SELected]\|:FDD>:UPLink:CHANnel
*RST Setting	see CALL:SETup[:PCReconfig]:CHANnel<[:SELected]\|:FDD>:UPLink:CHANnel
Requirements	Test Application Revision: A.06 and above Lab Application Revision: C.01 and above Test Application Revision A.09 and Lab Application Revisions C.04 and D.00, added [:CHANnel] All other changes match the CALL:SETup[:PCReconfig]:CHANnel<[:SELected]\|:FDD>:UPLink:CHANnel command.
Programming Example OUTPUT 714;"CALL:STATus:SETup:CHANnel:UPLink?"

CALL:STATus:SETup[:PCReconfig]:CHANnel<[:SELected]|:FDD>UPLink:SEParation?

Function	Queries the PCR Info, DL/UL Frequency Separation .
Query	Range: MHZ30\|MHZ31\|MHZ45\|MHZ48\|MHZ80\|MHZ95\|MHZ120\|MHZ190\|MHZ400\|NSTD
*RST Setting	MHZ190
Requirements	Test Application Revision: A.09 and above Test Application Revision A.10.01, added MHZ120 Test Application Revision A.11, added [:PCReconfig] Lab Application Revision: C.04 and above Lab Application Revision: D.00 and above Lab Application Revision D.01.01, added MHZ120 Lab Application Revision D.02, added [:PCReconfig] Lab Application Revision E.00.34, added MHZ48 Test Application Revision A.14 and Lab Application Revision F.00, added MHZ30 and MHZ31
Programming Example OUTPUT 714;"CALL:STATus:SETup:CHANnel:UPLink:SEParation?"

CALL:STATus:SETup[:PCReconfig]:FBINdicator?

Function	Queries the PCR Info, Frequency Band .
Query	Range: BAND1\|BAND2\|BAND3\|BAND4\|BAND5\|BAND6\|BAND7\|BAND8\|BAND9\|BAND10\| BAND11\|BAND12\|BAND13\|BAND14
*RST Setting	BAND1
Requirements	Test Application Revision: A.09 and above Lab Application Revisions: C.04 and D.00 and above Test Application Revision A.10.01 and Lab Application Revision D.01.01, added BAND7 Test Application Revision A.11 and Lab Application Revisions D.02 and E.00, added BAND10 Test Application Revision A.11 and Lab Application Revision D.02, added [:PCReconfig] Test Application Revision A.13 and Lab Application Revision E.00.34, added BAND11 Test Application Revision A.14 and Lab Application Revision F.00, added BAND12, BAND13, and BAND14
Programming Example OUTPUT 714;"CALL:STATus:SETup:FBINdicator?"

CALL:STATus:SETup:RBReconfig:CHANnel:UPLink[:CHANnel]?

Function	Queries RBR Info, UL: Channel and Frequency .
Query	Range: see CALL:SETup:RBReconfig:CHANnel:UPLink:CHANnel
*RST Setting	see CALL:SETup:RBReconfig:CHANnel:UPLink:CHANnel
Requirements	Test Application Revision A.11 and Lab Application Revision D.02 and above Lab Application Revision: E.00.34 and above, added 3487 - 3587. Test Application Revision A.14 and Lab Application Revision F.00 and above, added 3612 - 3678, 3702, 3707, 3732, 3737, 3762, 3767, 3792 - 3818, 3842, 3867, 3892 - 3918, 3942, 3967
Programming Example OUTPUT 714;"CALL:STATus:SETup:RBReconfig:CHANnel:UPLink?"

CALL:STATus:SETup:RBReconfig:CHANnel:UPLink:SEParation?

Function	Queries RBR Info, DL/UL Frequency Separation .
Query	Range: MHZ30\|MHZ31\|MHZ45\|MHZ48\|MHZ80\|MHZ95\|MHZ120\|MHZ190\|MHZ400\|NSTD
*RST Setting	MHZ190
Requirements	Test Application Revision A.11 and Lab Application Revision D.02 and above Lab Application Revision E.00.34, added MHZ48 Test Application Revision A.14 and Lab Application Revision F.00, added MHZ30 and MHZ31
Programming Example OUTPUT 714;"CALL:STATus:SETup:RBReconfig:CHANnel:UPLink:SEParation?"

CALL:STATus:SETup:RBReconfig:DPCHannel:CBETa?

Function	Queries the beta_c value that the test set will signal to the UE during the Radio Bearer Reconfiguration (see RBR Uplink DPCH Bc/Bd Control ).
Query	Range: 1 to 15 Resolution: 1
*RST Setting	8
Requirements	Test Application Revision: A.09 and above Lab Application Revision: C.04 and above Lab Application Revision: D.00 and above Test Application Revision A.11 and Lab Application Revisions D.02 and E.00, range is 1 to 15 (vs. 2 to 15)
Programming Example OUTPUT 714;"CALL:STATus:SETup:RBReconfig:DPCHannel:CBETa?"

CALL:STATus:SETup:RBReconfig:DPCHannel:DBETa?

Function	Queries the beta_d value that the test set will signal to the UE during the Radio Bearer Reconfiguration (see RBR Uplink DPCH Bc/Bd Control ).
Query	Range: 0 to 15 Resolution: 1
*RST Setting	15
Requirements	Test Application Revision: A.09 and above Lab Application Revision: C.04 and above Lab Application Revision: D.00 and above
Programming Example OUTPUT 714;"CALL:STATus:SETup:RBReconfig:DPCHannel:DBETa?"

CALL:STATus:SETup:RBReconfig:FBINdicator?

Function	Queries RBR Info, Frequency Band .
Query	Range: BAND1\|BAND2\|BAND3\|BAND4\|BAND5\|BAND6\|BAND7\|BAND8\|BAND9\|BAND10\| BAND11\|BAND12\|BAND13\|BAND14
*RST Setting	BAND1
Requirements	Test Application Revision A.11 and Lab Application Revision D.02 and above Lab Application Revision: E.00.34 and above, added BAND11 Test Application Revision A.14 and Lab Application Revision F.00, added BAND12, BAND13, and BAND14
Programming Example OUTPUT 714;"CALL:STATus:SETup:RBReconfig:FBINdicator?"

CALL:STATus:SETup:TCReconfig:CHANnel:UPLink[:CHANnel]?

Function	Queries TCR Info, UL: Channel and Frequency .
Query	Range: see CALL:SETup:TCReconfig:CHANnel:UPLink:CHANnel
*RST Setting	see CALL:SETup:TCReconfig:CHANnel:UPLink:CHANnel
Requirements	Test Application Revision A.11 and Lab Application Revision D.02 and above Lab Application Revision: E.00.34 and above, added 3487 - 3587. Test Application Revision A.14 and Lab Application Revision F.00 and above, added 3612 - 3678, 3702, 3707, 3732, 3737, 3762, 3767, 3792 - 3818, 3842, 3867, 3892 - 3918, 3942, 3967
Programming Example OUTPUT 714;"CALL:STATus:SETup:TCReconfig:CHANnel:UPLink?"

CALL:STATus:SETup:TCReconfig:CHANnel:UPLink:SEParation?

Function	Queries TCR Info, DL/UL Frequency Separation .
Query	Range: MHZ30\|MHZ31\|MHZ45\|MHZ48\|MHZ80\|MHZ95\|MHZ120\|MHZ190\|MHZ400\|NSTD
*RST Setting	MHZ190
Requirements	Test Application Revision A.11 and Lab Application Revision D.02 and above Lab Application Revision E.00.34, added MHZ48 Test Application Revision A.14 and Lab Application Revision F.00, added MHZ30 and MHZ31
Programming Example OUTPUT 714;"CALL:STATus:SETup:TCReconfig:CHANnel:UPLink:SEParation?"

CALL:STATus:SETup:TCReconfig:DPCHannel:CBETa?

Function	Queries the beta_c value that the test set will signal to the UE during the Transport Channel Reconfiguration (see TCR DPCH Bc/Bd Control ).
Query	Range: 1 to 15 Resolution: 1
*RST Setting	8
Requirements	Test Application Revision: A.09 and above Lab Application Revision: C.04 and above Lab Application Revision: D.00 and above Test Application Revision A.11 and Lab Application Revisions D.02 and E.00, range is 1 to 15 (vs. 2 to 15)
Programming Example OUTPUT 714;"CALL:STATus:SETup:TCReconfig:DPCHannel:CBETa?"

CALL:STATus:SETup:TCReconfig:DPCHannel:DBETa?

Function	Queries the beta_d value that the test set will signal to the UE during the Transport Channel Reconfiguration (see TCR DPCH Bc/Bd Control ).
Query	Range: 0 to 15 Resolution: 1
*RST Setting	15
Requirements	Test Application Revision: A.09 and above Lab Application Revision: C.04 and above Lab Application Revision: D.00 and above
Programming Example OUTPUT 714;"CALL:STATus:SETup:TCReconfig:DPCHannel:DBETa?"

CALL:STATus:SETup:TCReconfig:FBINdicator?

Function	Queries TCR Info, Frequency Band .
Query	Range: BAND1\|BAND2\|BAND3\|BAND4\|BAND5\|BAND6\|BAND7\|BAND8\|BAND9\|BAND10\| BAND11\|BAND12\|BAND13\|BAND14
*RST Setting	BAND1
Requirements	Test Application Revision A.11 and Lab Application Revision D.02 and above Test Application Revision A.13 and Lab Application Revision E.00.34 and above, added BAND11 Test Application Revision A.14 and Lab Application Revision F.00, added BAND12, BAND13, and BAND14
Programming Example OUTPUT 714;"CALL:STATus:SETup:TCReconfig:FBINdicator?"

CALL:STATus:SGRant:RELative:QUEued:COUNt?

Function	Queries Queued Relative Grants .
Query	Range: 0 to 1000
*RST Setting	0
Requirements	Test Application Revision A.12 and above, with the required feature license Lab Application Revision E.00.16 and above
Programming Example OUTPUT 714;"CALL:STATus:SGRant:RELative:QUEued:COUNt?"

CALL:STATus:SHANdoff:EVENt?

Function	Queries the most recent Intra Frequency Event identifier. Events can be: 1a 1b 1c 1d 1e 1f None (See Event Reporting ).
Query	Range: 1A\|1B\|1C\|1D\|1E\|1F\|NONE
*RST Setting	NONE
Requirements	Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:SHANdoff:EVENt?" !Returns the most recent event.

CALL:STATus:SHANdoff:EVENt:CELLid?

Function	Queries the cell that triggered the most recent event. (See Event Reporting ).
Query	Range: CELL1\|CELL2\|NONE
*RST Setting	NONE
Requirements	Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:SHANdoff:EVENt:CELLid?"

CALL:STATus:SHANdoff:STATe?

Function	Queries Soft Handover State .
Query	Range: 1\|0
*RST Setting	0
Requirements	Lab Application Revision: B.01 and above
Programming Example OUTPUT 714;"CALL:STATus:SHANdoff:STATe?"

CALL:STATus:TOTal:POWer[:AMPLitude]?

Function	Queries the current total RF power for the specified system type. The total RF power is equal to the sum of the cell power setting (see CALL:POWer ) and the AWGN setting (see CALL:AWGNoise ). See Cell Power and AWGN Power for more information about desired versus current power levels.
Query	Range: -165 dBm/3.84 MHz to +42 dBm/3.84 MHz, NAN (this is the range of settings accepted, see Cell Power, AWGN Power and Total RF Power Ranges for the actual hardware range of the source) 9.91 E+37 (NAN) is returned if CALL:STATus:TOTal:POWer:STATe? is OFF Resolution: 0.01 dB
*RST Setting	-75.00 dBm
Requirements	Test or Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:TOTal:POWer?"

CALL:STATus:TOTal:POWer:STATe?

Function	Queries the current total RF power measurement's state for the currently selected system type. This query will return a 1 (on) if the current cell power ( CALL:POWer ) power state is on.
Query	Range: 1\|0
*RST Setting	1 (on)
Requirements	Test or Lab Application Revision: A.01 and above
Programming Example OUTPUT 714;"CALL:STATus:TOTal:POWer:STATe?"

CALL:STATus:UPLink:CHANnel?

Function	Queries the Current Info, UL: Channel and Frequency .
Query	Range: see CALL:UPLink:CHANnel:CHANnel
*RST Setting	9750
Requirements	Test Application Revision: A.06 and above Lab Application Revision: C.01 and above All other changes match the CALL:UPLink:CHANnel:CHANnel command.
Programming Example OUTPUT 714;"CALL:STATus:UPLink:CHANnel?"

CALL:STATus:UPLink:SEParation?

Function	Queries the Current Info, DL/UL Frequency Separation .
Query	Range: MHZ30\|MHZ31\|MHZ45\|MHZ48\|MHZ80\|MHZ95\|MHZ120\|MHZ190\|MHZ400\|NSTD
*RST Setting	MHZ190
Requirements	Test Application Revision: A.08 and above Lab Application Revision: C.03 and above Test Application Revision A.10.01 and Lab Application Revision D.01.01 added MHZ120 Lab Application Revision E.00.34, added MHZ48 Test Application Revision A.14 and Lab Application Revision F.00, added MHZ30 and MHZ31
Programming Example OUTPUT 714;"CALL:STATus:UPLink:SEParation?"