RFANalyzer

Function

Turns on/off the auto Measurement Frequency feature which determines the measurement downconverter signal path frequency control mode. (See Block Diagram .)

ON = automatic

OFF = manual (see RFANalyzer:MANual:MEASurement[:MFRequency] and RFANalyzer:MANual:MEASurement:FREQuency )

Note, when you switch between operating modes, Measurement Frequency is returned to its default value of Auto .

Setting

Query

Range: 1|0

Requirements

Test or Lab Application Revision: A.01 and above

Programming Example

 
OUTPUT 714;"RFANalyzer:CONTrol:MEASurement:FREQuency:AUTO OFF" 
!Enables manual control of the measurement signal path tune frequency.

Function

Sets/queries Power Control .

ON = automatic

OFF = manual (see RFANalyzer:MANual:POWer[:SELected] )

This command is available in Active Cell , FDD Test and Cell Off operating modes.

Note, when you switch between operating modes, Power Control is returned to its default value of Auto .

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

Requirements

Test or Lab Application Revision: A.01 and above

Programming Example

 
OUTPUT 714;"RFANALYZER:CONTROL:POWER:AUTO OFF" 

 
!Enables manual control of the expected input power level.

Function

Turns on/off the auto Uplink Frequency feature, which determines the test set's demodulation signal path tune frequency control mode.

ON = automatic

OFF = manual (see RFANalyzer:MANual:UPLink[:MFRequency] and RFANalyzer:MANual:UPLink:FREQuency .

This setting is available in FDD Test and CW operating modes.

Note, when you switch between operating modes, Uplink Frequency is returned to its default value of Auto .

Setting

Range: 1|ON|0|OFF

Query

Range: 1|0

Requirements

Test or Lab Application Revision: A.01 and above

Programming Example

 
OUTPUT 714;"RFANALYZER:CONTROL:UPLINK:FREQUENCY:AUTO OFF" !Enables manual control of the demodulation signal path tune frequency.

Function

Sets/queries the expected CW receiver input power. This setting is only used when the Operating Mode is set to CW. (See CALL:OPERating .)

Setting

Range: -60 dBm to +53 dBm

Query

Range: -60 dBm to +53 dBm

Requirements

Test or Lab Application Revision: A.01 and above

Programming Example

 
OUTPUT 714;"RFANALYZER:CW:EXPECTED:POWER -20" 

Function

Sets/queries Manual Power (the optional [:SELected] keyword in this command specifies that the manual power setting applies to the current system type). This command is only applicable when RFANalyzer:CONTrol:POWer:AUTO ( Power Control ) is set to Off (manual).

This command is available in Active Cell , FDD Test and Cell Off operating modes.

Note, when you switch between operating modes, Power Control is returned to its default value of Auto .

Setting

Range: Test application and system type dependent (approximately -25 to +43 dBm).

Resolution: 0.01 dBm

Query

Requirements

Test or Lab Application Revision: A.01 and above

Programming Example

 
OUTPUT 714;"RFANALYZER:MANUAL:POWER:SELECTED 24 DBM" !Sets the manual power control mode expected input power level for the currently selected system type to 24 dBm.

Function

Sets/queries Manual Power when UTRA FDD is the current system type. This command is only applicable when RFANalyzer:CONTrol:POWer:AUTO ( Power Control ) is set to Off (manual).

This command is available in Active Cell , FDD Test and Cell Off operating modes.

Note, when you switch between operating modes, Power Control is returned to its default value of Auto .

Setting

Range: -129 to +80 dBm (-79 dBm to +30 dBm actual hardware range with amplitude offset = 0)

Resolution: 0.01 dBm

Query

Requirements

Test or Lab Application Revision: A.01 and above

Programming Example

 
OUTPUT 714;"RFANALYZER:MANUAL:POWER:FDD 24 DBM" 
!Sets the manual power control mode expected input power level for the FDD system type to
!24 dBm.

Function

The setting form of this command performs two functions: (1) sets Measurement Frequency , the tune frequency of the test set's measurement signal path, and (2) selects manual (auto off) tune mode for the test set's measurement signal path.

The query form of this command returns the tune frequency of the test set's measurement signal path.

The tune mode for the test set's measurement signal path can be returned to auto using the RFANalyzer:CONTrol:MEASurement:FREQuency:AUTO command.

Note, when you switch between operating modes, Measurement Frequency is returned to its default value of Auto .

Setting

Range: 292.5 MHz to 2700 MHz

Resolution: 0.1 Hz

Query

Requirements

Test or Lab Application Revision: A.01 and above

Programming Example

 
OUTPUT 714;"RFANALYZER:MANUAL:MEASUREMENT:MFREQUENCY 942.6 MHZ" 
!Enables manual control of the measurement signal path tune frequency and sets the tune frequency to 942.6 MHz.

Function

Sets/queries Measurement Frequency .

This setting is applied when manual mode is selected for Measurement Frequency (see RFANalyzer:CONTrol:MEASurement:FREQuency:AUTO ).

Note, when you switch between operating modes, Measurement Frequency is returned to its default value of Auto .

Setting

Range: 292.5 MHz to 2700 MHz

Resolution: 0.1 Hz

Query

Requirements

Test or Lab Application Revision: A.01 and above

Programming Example

 
OUTPUT 714;"RFANALYZER:MANUAL:MEASUREMENT:FREQUENCY 942.6 MHZ" 
!Sets the measurement signal path tune frequency to 942.6 MHz when manual control mode is used.

Function

The setting form of this command performs two functions: (1) sets Uplink Frequency , the tune frequency of the test set's demodulation signal path, and (2) selects manual (auto off) tune mode for the test set's demodulation signal path.

The query form of this command returns the tune frequency of the test set's demodulation signal path.

The tune mode for the test set's demodulation path can be returned to auto using the RFANalyzer:CONTrol:UPLink:FREQuency:AUTO command.

This setting is available in FDD Test and CW operating modes.

Note, when you switch between operating modes, Uplink Frequency is returned to its default value of Auto .

Setting

Range: 292.5 MHz to 2700 MHz

Resolution: 0.1 Hz

Query

Requirements

Test or Lab Application Revision: A.01 and above

Programming Example

 
OUTPUT 714;"RFANALYZER:MANUAL:UPLINK:MFREQUENCY 1955.030 MHZ"

 
!Enables manual control of the demodulation signal path tune frequency and sets the tune frequency 
!to 1955.030 MHz.

Function

Sets/queries Uplink Frequency .

This setting is applied when manual mode is selected for Uplink Frequency (see RFANalyzer:CONTrol:UPLink:FREQuency:AUTO ).

This setting is available in FDD Test and CW operating modes.

Note, when you switch between operating modes, Uplink Frequency is returned to its default value of Auto .

Setting

Range: 292.5 MHz to 2700 MHz

Resolution: 0.1 Hz

Query

Range: 292.5 MHz to 2700 MHz

Requirements

Test or Lab Application Revision: A.01 and above

Programming Example

 
OUTPUT 714;"RFANALYZER:MANUAL:UPLINK:FREQUENCY 942.6 MHZ" 
!Sets the test set's demodulation signal path tune frequency to 942.6 MHz.