SETup:WTPower
Last updated: January 16, 2009
GPIB Command Conventions
SETup:WTPower:CONTinuous
|
Function
|
Sets/queries the trigger arm state for the thermal power measurement. The trigger arm state determines whether the thermal power measurement will be made once then stop (0|OFF (single)), or automatically rearm upon completion of one measurement and repeat the process (1|ON (continuous)).
|
|
Setting
|
Range: 1|ON|0|OFF
|
|
Query
|
Range: 1|0
|
|
*RST Setting
|
0 (off)
|
|
Requirements
|
Test or Lab Application Revision: A.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:WTPOWER:CONTINUOUS ON"
!Sets measurement to single trigger mode.
|
SETup:WTPower:COUNt[:SNUMber]
|
Function
|
The setting form of this command performs two functions: (1) sets the number of thermal power measurements to be made in a multi-measurement, and (2) sets the multi-measurement STATe command to 1 (on).
The query form returns the number of thermal power multi-measurements to be made when multi-measurement state is ON.
|
|
Setting
|
Range: 1 to 999
|
|
Query
|
Range: 1 to 999
|
|
*RST Setting
|
Off (10 when STATe = On) |
|
Requirements
|
Test or Lab Application Revision: A.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:WTPOWER:COUNT:SNUMBER 5"
!Turns on multi-measurements and sets the number of measurements to 5.
|
SETup:WTPower:COUNt:NUMBer
|
Function
|
Sets/queries the number of thermal power measurements to be made when the multi-measurement state is ON.
|
|
Setting
|
Range: 1 to 999
|
|
Query
|
Range: 1 to 999
|
|
*RST Setting
|
10 |
|
Requirements
|
Test or Lab Application Revision: A.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:WTPOWER:COUNT:NUMBER 5"
!Sets the number of measurements to 5 when the multi-measurement state is set to ON.
|
SETup:WTPower:COUNt:STATe
|
Function
|
Sets/queries the multi-measurement state of the thermal power measurement.
|
|
Setting
|
Range: 1|ON|0|OFF
|
|
Query
|
Range: 1|0
|
|
*RST Setting
|
0 (off)
|
|
Requirements
|
Test or Lab Application Revision: A.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:WTPOWER:COUNT:STATE ON" !Turns on multi-measurements.
|
SETup:WTPower:TIMeout[:STIMe]
|
Function
|
The setting form of this command performs two functions: (1) sets the thermal power measurement's timeout value, and (2) sets the thermal power measurement's timeout STATe to 1 (on).
The query form returns the channel power measurement's timeout value.
|
|
Setting
|
Range: 1 to 999 seconds
Resolution: 1 second
|
|
Query
|
Range: 1 to 999
|
|
*RST Setting
|
10 seconds, off
|
|
Requirements
|
Test or Lab Application Revision: A.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:WTPOWER:TIMEOUT:STIME 5S"
!Sets timeout state to ON and sets the timeout time to 5 seconds.
|
SETup:WTPower:TIMeout:STATe
|
Function
|
Sets/queries the thermal power measurement's timeout state.
|
|
Setting
|
Range: 1|ON|0|OFF
|
|
Query
|
Range: 1|0
|
|
*RST Setting
|
0 (off)
|
|
Requirements
|
Test or Lab Application Revision: A.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:WTPOWER:TIMEOUT:STATE ON"
|
SETup:WTPower:TIMeout:TIME
|
Function
|
Sets/queries the thermal power measurement's timeout setting to be used when the timeout state is set to ON.
|
|
Setting
|
Range: 1 to 999 seconds
Resolution: 1 second
|
|
Query
|
Range: 1 to 999
|
|
*RST Setting
|
10 seconds
|
|
Requirements
|
Test or Lab Application Revision: A.01 and above
|
|
Programming Example
OUTPUT 714;"SETUP:WTPOWER:TIMEOUT:TIME 5S"
|
|
top
of page