Activate PDP Context Reject
Last updated: January 16, 2009
This section is only applicable to the lab application.
You may configure the test set to simulate a network rejection of an Activate PDP Context Request from the UE by setting
Activate PDP Context Reject State
to
On
. You can choose what value is sent in the SM Cause information element of the Activate PDP Context Reject message using the
Activate PDP Context Reject SM Cause
setting. Use this function in parallel with
Protocol Logging
to verify that the UE behaves in a manner conforming to the standards for this situation and for each associated SM Cause value.
Activate PDP Context Reject SM Cause
When
Activate PDP Context Reject State
is
On
, you may specify what value is sent in the SM Cause information element using the
Activate PDP Context Reject SM Cause
setting. From the front panel, you may choose from the valid causes specified in 3GPP TS 24.008 10.5.6.6.
Activate PDP Context Reject SM Cause
|
Cause Value (decimal) |
Cause Value (bits) |
Cause |
|
25 |
00011001 |
LLC or SNDCP Failure |
|
26 |
00011010 |
Insufficient Resources |
|
27 |
00011011 |
Missing or Unknown APN |
|
28 |
00011100 |
Unknown PDP Address or PDP Type |
|
29 |
00011101 |
User Authentication Failed |
|
30 |
00011110 |
Activation Rejected By GGSN |
|
31 |
00011111 |
Activation Rejected, Unspecified |
|
32 |
00100000 |
Service Option Not Supported |
|
33
|
00100001
|
Requested Service Opt Not Subscribed
|
|
34 |
00100010 |
Service Opt Temporarily Out of Order |
|
35 |
00100011 |
NSAPI Already Used |
|
36 |
00100100 |
Regular Deactivation |
|
37 |
00100101 |
QoS Not Accepted |
|
38 |
00100110 |
Network Failure |
|
39 |
00100111 |
Reactivation Required |
|
40 |
00101000 |
Feature Not Supported |
|
41 |
00101001 |
Semantic Error in TFT Operation |
|
42 |
00101010 |
Syntactical Error in TFT Operation |
|
43 |
00101011 |
Unknown PDP Context |
|
44 |
00101100 |
Semantic Error in Packet Filter(s) |
|
45 |
00101101 |
Syntactical Errors in Packet Filters(s) |
|
46 |
00101110 |
PDP Context Without TFT Already Activated |
|
81 |
01010001 |
Invalid Transaction Identifier Value |
|
95 |
01011111 |
Semantically Incorrect Message |
|
96 |
01100000 |
Invalid Mandatory Information |
|
97 |
01100001 |
Msg Type Non-existent/Not Implemented |
|
98 |
01100010 |
Msg Type Not Compatible With Protocol State |
|
99 |
01100011 |
IE Non-existent or Not Implemented |
|
100 |
01100100 |
Conditional IE Error |
|
101
|
01100101
|
Msg Not Compatible With Protocol State
|
|
111 |
01101111 |
Protocol Error, Unspecified |
If you select
Custom Value
from the front panel, a value of 0 is sent to the UE.
The
CALL:SERVice:GPRS:REJect:CAUSe
command allows you to send any value between 0 and 255 to the UE, even those not mapped to a cause in the standard. If you send a value other than those listed in the above table via the GPIB command, the front panel setting displays
CUSTOM
.
|
top
of page