Erreurs de périphériques (-300…)
Erreurs diverses (+300... et +500..)
Erreurs de licence et d'autotest (+600...)
L'appareil renvoie des messages d'erreur conformément à la norme SCPI.
-100,"Command error"
-101,"Invalid character"
-102,"Syntax error"
-103,"Invalid separator"
-104,"Data type error"
-105,"GET not allowed"
-108,"Parameter not allowed"
-109,"Missing parameter"
-110,"Command header error"
-111,"Header separator error"
-112,"Program mnemonic too long"
-113,"Undefined header"
-114,"Header suffix out of range"
-120,"Numeric data error"
-121,"Invalid character in number"
-123,"Exponent too large"
-123,"Numeric overflow"
-124,"Too many digits"
-128,"Numeric data not allowed"
-130,"Suffix error"
-131,"Invalid suffix"
-134,"Suffix too long"
-138,"Suffix not allowed"
-140,"Character data error"
-141,"Invalid character data"
-144,"Character data too long"
-148,"Character data not allowed"
-150,"String data error"
-151,"Invalid string data"
-158,"String data not allowed"
-160,"Block data error"
-161,"Invalid block data"
-168,"Block data not allowed"
-200,"Execution error"
-203,"Command protected"
-203,"Command protected; external trigger requires license LAN"
-203,"Command protected; License required"
-203,"Command protected; requires license LAN"
-203,"Command protected; requires license SEC"
-210,"Trigger error"
-211,"Trigger ignored"
-213,"Init ignored"
-214,"Trigger deadlock"
-220,"Parameter error"
-221,"Settings conflict"
-221,"Settings conflict; *TRG when TRIG:SOUR BUS not selected; trigger ignored"
-221,"Settings conflict; 10A current terminals not available with rear terminals; terminals set to 3A"
-221,"Settings conflict; CALC function not allowed in current measurement function; CALC:STAT OFF set"
-221,"Settings conflict; CALC not allowed in current measurement function"
-221,"Settings conflict; CALC not allowed in current measurement function; CALC:STAT OFF set"
-221,"Settings conflict; CALC:AVER:STATe OFF set"
-221,"Settings conflict; CALC:TRAN:HIST:STATe OFF set"
-221,"Settings conflict; CALCulate not allowed in current function"
-221,"Settings conflict; cannot delete state selected and enabled for automatic power-on recall"
-221,"Settings conflict; histogram lower range > upper range; CALC:TRAN:HIST:RANG:AUTO ON set"
-221,"Settings conflict; lower limit > upper limit; CALC:LIM:UPP set to CALC:LIM:LOW value"
-221,"Settings conflict; trigger source is BUS"
-222,"Data out of range"
-222,"Data out of range; value clipped to lower limit"
-222,"Data out of range; value clipped to upper limit"
-223,"Too much data"
-224,"Illegal parameter value"
-225,"Out of memory; measurement data overrun"
-230,"Data corrupt or stale"
-231,"Data questionable"
-240,"Hardware error"
-240,"Hardware error; cannot communicate with measurement hardware"
-240,"Hardware error; CPU board initialization failed"
-240,"Hardware error; GPIB interface failed"
-240,"Hardware error; measurement FPGA FIFO overflow"
-240,"Hardware error; measurement hardware initialization failed"
-256,"File name not found"
-256,"File or folder name not found"
-257,"File name error"
-257,"File name error; access denied"
-257,"File name error; drive name missing or not recognized"
-257,"File name error; file or folder already exists"
-257,"File name error; file too large"
-257,"File name error; folder is default folder"
-257,"File name error; folder not empty"
-257,"File name error; invalid character in name"
-257,"File name error; not a folder name"
-257,"File name error; path is a folder name"
-257,"File name error; path too long"
-257,"File name error; relative path not allowed"
-257,"File name error; unknown file extension"
-300,"Device specific error"
-310,"System error"
-310,"System error; internal software error"
-310,"System error; out of memory"
-310,"System error; software initialization failed"
-330,"Self-test failed"
-350,"Queue overflow"
-400,"Query error"
-410,"Query INTERRUPTED"
-420,"Query UNTERMINATED"
-430,"Query DEADLOCKED"
-440,"Query UNTERMINATED after indefinite response"
+263,"Not able to execute while instrument is measuring"
+291,"Not able to recall state: it is empty"
+292,"State file size error"
+293,"State file corrupt"
+294,"Preference file size error"
+295,"Preference file corrupt"
+305,"Not able to perform requested operation"
+311,"Not able to specify resolution with Auto range"
+514,"Not allowed; Instrument locked by another I/O session"
+521,"Communications: input buffer overflow"
+532,"Not able to achieve requested resolution"
+540,"Cannot use overload as math reference"
+542,"Measured dB reference too small"
+550,"Not able to execute command in local mode"
+600,"Internal licensing error"
+601,"License file corrupt or empty"
+602,"No valid licenses found for this instrument"
+603,"Some licenses could not be installed"
+604,"License not found"
+611,"Self-test failed; Real Time Clock reset, check battery"
+612,"Self-test failed; keyboard processor not responding"
+613,"Self-test failed; unable to communicate with power controller"
+614,"Self-test failed; unable to sense line frequency"
+615,"Self-test failed; measurement processor not responding"
+616,"Self-test failed; calibration memory reading error"
+617,"Self-test failed; FPGA unconfigured"
+618,"Self-test failed; FPGA bus error"
+619,"Self-test failed; FPGA clock"
+620,"Self-test failed; shift register"
+621,"Self-test failed; overload sense stuck on"
+622,"Self-test failed; ADC generic error"
+623,"Self-test failed; ADC integrator saturated"
+624,"Self-test failed; Coarse ADC error"
+625,"Self-test failed; ADC offset"
+626,"Self-test failed; ADC noise"
+627,"Self-test failed; Fine ADC generic error"
+628,"Self-test failed; Fine ADC off-scale low"
+629,"Self-test failed; Fine ADC off-scale high"
+630,"Self-test failed; Fine ADC range"
+631,"Self-test failed; Fine ADC bits stuck"
+632,"Self-test failed; Fine ADC slope"
+633,"Self-test failed; Fine ADC linearity"
+634,"Self-test failed; low DC zero"
+635,"Self-test failed; high DC zero"
+636,"Self-test failed; +7V reference"
+637,"Self-test failed; -10V reference"
+638,"Self-test failed; x1 gain, zero input"
+639,"Self-test failed; x10 gain, zero input"
+640,"Self-test failed; x100 gain, zero input"
+641,"Self-test failed; precharge"
+642,"Self-test failed; x1 gain, non-zero input"
+643,"Self-test failed; x10 gain, non-zero input"
+644,"Self-test failed; x100 gain, non-zero input"
+645,"Self-test failed; 100uA current source"
+646,"Self-test failed; 10uA current source"
+647,"Self-test failed; 2 ohm shunt"
+648,"Self-test failed; AC offset"
+649,"Self-test failed; frequency input"
+650,"Self-test failed; input switch"
+701,"Calibration error; security defeated"
+702,"Calibration error; calibration memory is secured"
+703,"Calibration error; secure code provided was invalid"
+704,"Calibration error: secure code too long"
+705,"Calibration error; calibration aborted"
+706,"Calibration error: provided value out of range"
+707,"Calibration error: computed correction factor out of range"
+708,"Calibration error: signal measurement out of range"
+708,"Calibration error; signal frequency out of range"
+709,"Calibration error: no calibration for this function"
+710,"Calibration error: full scale correction out of range"
+711,"Calibration error: calibration string too long"
+713,"Calibration error; ADC calibration failed; ADC configuration 'ACI' did not converge"
+713,"Calibration error; ADC calibration failed; ADC configuration 'ACV' did not converge"
+713,"Calibration error; ADC calibration failed; ADC configuration 'DCV' did not converge"
+713,"Calibration error; ADC calibration failed; DC offset for setup 'ACI'"
+713,"Calibration error; ADC calibration failed; DC offset for setup 'ACV'"
+713,"Calibration error; ADC calibration failed; DC offset for setup 'DCV'"
+713,"Calibration error; ADC calibration failed; feedbackLutGainTune unsupported LUT goal"
+713,"Calibration error; ADC calibration failed; feedbackLutTune search did not converge"
+713,"Calibration error; ADC calibration failed; feedbackPiCancel did not converge for setup 'ACI'"
+713,"Calibration error; ADC calibration failed; feedbackPiCancel did not converge for setup 'ACV'"
+713,"Calibration error; ADC calibration failed; feedbackPiCancel did not converge for setup 'DCV'"
+713,"Calibration error; ADC calibration failed; fine merge for setup 'ACI'"
+713,"Calibration error; ADC calibration failed; fine merge for setup 'ACV'"
+713,"Calibration error; ADC calibration failed; fine merge for setup 'DCV'"
+713,"Calibration error; ADC calibration failed; fine offset for setup 'ACI'"
+713,"Calibration error; ADC calibration failed; fine offset for setup 'ACV'"
+713,"Calibration error; ADC calibration failed; fine offset for setup 'DCV'"
+713,"Calibration error; ADC calibration failed; fineDcCancel found non-monotonic value in setup 'ACI'"
+713,"Calibration error; ADC calibration failed; fineDcCancel found non-monotonic value in setup 'ACV'"
+713,"Calibration error; ADC calibration failed; fineDcCancel found non-monotonic value in setup 'DCV'"
+713,"Calibration error; ADC calibration failed; LUT gain for setup 'ACI'"
+713,"Calibration error; ADC calibration failed; LUT gain for setup 'ACV'"
+713,"Calibration error; ADC calibration failed; LUT gain for setup 'DCV'"
+713,"Calibration error; ADC calibration failed; LUT goal incompatible with ACV"
+713,"Calibration error; ADC calibration failed; PI offset for setup 'ACI'"
+713,"Calibration error; ADC calibration failed; PI offset for setup 'ACV'"
+713,"Calibration error; ADC calibration failed; PI offset for setup 'DCV'"
+713,"Calibration error; DCV 10M input impedance gain adjustment out of range"
+713,"Calibration error; must perform +100mV DCV calibration before -100mV"
+713,"Calibration error; must perform +10V DCV calibration before -10V"
+713,"Calibration failed"
+715, "Calibration error; must perform +100uA DCI calibration before -100uA"
+715, "Calibration error; must perform 10MOhm calibration before 100MOhm"
+720,"Calibration error; DCV offset out of range"
+721,"Calibration error; DCI offset out of range"
+722,"Calibration error; RES offset out of range"
+723,"Calibration error; FRES offset out of range"
+724,"Calibration error; extended resistance self cal failed"
+725,"Calibration error; 1000V DC correction out of range"
+726,"Calibration error; ACV offset out of range"
+727,"Calibration error; ACI offset out of range"
+730,"Calibration error; precharge DAC convergence failed"
+731,"Calibration error; A/D turnover correction out of range"
+732,"Calibration error; AC flatness calibration failed"
+733,"Calibration error; AC low frequency correction out of range"
+734,"Calibration error; AC flatness calibration restarted by function/range change"
+735,"Calibration error; 1 kHz AC flatness frequency point must be last frequency point in sequence"
+740,"Calibration information lost; count, security state, security code, string"
+742,"Calibration data lost: corrections"
+746, "System information write failure";
+747, "System information read failure";
+748,"Calibration memory write failure"
+749,"Calibration memory read failure"