Manual User Error Messages

The function you requested is not yet available.

The test set does not have this capability.

IQ Calibration completed successfully for modulator <N>

<N> is the IQ modulator number that you are attempting to calibrate, <N> is 1 or 2.

IQ Calibration failed for modulator <N>

<N> is the IQ modulator number that you are attempting to calibrate, <N> is 1 or 2.

The function you requested is not available in this TA.

This function is used in another Test Application.

IQ Calibration for modulator 1 in progress (10 minutes). Call processing disabled.

This error is cleared by either the; IQ Calibration completed successfully for modulator <N>, or IQ Calibration failed for modulator <N>.

IQ Calibration for modulator 2 in progress (6 minutes). Call processing disabled.

This error is cleared by either the; IQ Calibration completed successfully for modulator <N>, or IQ Calibration failed for modulator <N>.

Instrument warning: Audio generator instrument has been closed.

The audio generator instrument was closed automatically by the test set.

Measurement warning: Audio Analyzer instrument has been closed.

Measurement warning: Analog audio measurement has been closed.

Protocol warning: Setting change has terminated the link with the DUT

Some setting change has caused the call to disconnect.

Warning; Call processing disabled

The call processing functions are not active because the test set is performing calibration operations.

IQ first modulator calibration X%

IQ modulator calibration in progress, X represents the percent complete.

IQ second modulator calibration X%

IQ modulator calibration in progress, X represents the percent complete.

If this error occurs during mobile station testing, an internal error has occurred in the test set's firmware.

If this error occurs during mobile station testing, an internal error has occurred in the test set's firmware.

This error message is displayed for information purposes only.

MUI211 "Channel power calibration failed due to temperature drift. Wait for temperature to stabilize"

This error message occurs when the internal temperature of the test set has drifted more that +/- 10 deg C since the last calibration. Normally, letting the test set fully warm up before calibrating will eliminate this problem.

MUI212 "Channel power calibration failed due to oven out of range"

The only user requirement for performing calibration is to make sure the test set is warmed up and to remove RF power to the front panel RF IN/OUT connector. If these requirements have been met and this message appears a test set failure condition exists.

MUI214 "Channel power calibration failed due to under range condition"

MUI215 "Channel power calibration failed due to over range condition"

The only user requirement for performing calibration is to make sure the test set is warmed up and to remove RF power to the front panel RF IN/OUT connector. If these requirements have been met and this message appears a test set failure condition exists.

MUI216 "Channel power calibration failed due to correlation problem"

The only user requirement for performing calibration is to make sure the test set is warmed up and to remove RF power to the front panel RF IN/OUT connector. If these requirements have been met and this message appears a test set failure condition exists.

MUI217 "Channel power calibration failed"

The only user requirement for performing calibration is to make sure the test set is warmed up and to remove RF power to the front panel RF IN/OUT connector. If these requirements have been met and this message appears a test set failure condition exists.

This error message is displayed for information purposes only.

This error message is displayed for information purposes only.

This error message is displayed for information purposes only.

This error message is displayed for information purposes only.

This error message is displayed for information purposes only.

This error message is displayed for information purposes only.

This error message is displayed for information purposes only.

This error message occurs when the internal temperature of the test set has drifted more that +/- 10 deg C since the last calibration. Normally, letting the test set fully warm up before calibrating will eliminate this problem.

This error message occurs when the internal temperature of the test set has drifted more that +/- 10 deg C since the last calibration. Normally, letting the test set fully warm up before calibrating will eliminate this problem.

The only user requirement for performing calibration is to make sure the test set is warmed up and to remove RF power to the front panel RF IN/OUT connector. If these requirements have been met and this message appears a test set failure condition exists.

The only user requirement for performing calibration is to make sure the test set is warmed up and to remove RF power to the front panel RF IN/OUT connector. If these requirements have been met and this message appears a test set failure condition exists.

This error message is displayed for information purposes only.

This error message is displayed for information purposes only.

This error message is displayed for information purposes only.

This error message is displayed for information purposes only.

This error message is displayed for information purposes only.

This error message is displayed for information purposes only.

This error message is displayed for information purposes only.

This error message is displayed for information purposes only.

This error message is displayed for information purposes only.

This error message is displayed for information purposes only.

This error message is displayed for information purposes only.

This error message is displayed for information purposes only.

This error message is displayed for information purposes only.

MUI252 CDMA measurement warning; Fast Device Tune measurement has been closed

MUI253 Frequency and Power Sequence tables built successfully

Select "Full" in the Traffic Data Rate field before attempting TX Spurious measurements.

MUI262 "CDMA measurement warning; Digital average power measurement is not accurate for gated MS transmissions in radio configurations greater than 2"

The test set can accurately measure gated MS transmissions in RC 1 and 2, but not in RC 3, 4 and 5. In RC 3, 4 and 5 it is sometimes impossible for the test set to know whether the MS is transmitting gated or not. So when this warning is seen, the user must decide whether or not their current setup leads to MS gated output or not.

See R-FCH Gating .

This error, during calibration, is part of the test set's normal operation.

If this error occurs during mobile station testing, an internal error has occurred in the test set's firmware.

MUI341 "Digital2000 warning; Handoff waveform quality measurement has been closed"

This error message is displayed for information purposes only.

MUI342 "Digital2000 warning; Code channel time/phase measurement has been closed"

This error message is displayed for information purposes only.

This error message is displayed for information purposes only.

This error, during calibration, is part of the test set's normal operation.

If this error occurs during mobile station testing, an internal error has occurred in the test set's firmware.