Last updated: November 25, 2010
A device-specific error indicates that the instrument has detected an error that occurred because some operations did not properly complete, possibly due to an abnormal hardware or firmware condition. For example, an attempt by the user to set an out of range value will generate a device specific error. Errors are categorized as follows:
When one of these errors is generated, the +700 errors bit in the questionable error status register is set.
|
+701 "CDMA measurement failure; Digital average power measurement is not responding" |
This error message indicates an internal software or hardware error. |
|
+702 "CDMA measurement failure; Waveform quality measurement is not responding" |
This error message indicates an internal software or hardware error. |
|
+703 "CDMA measurement failure; Channel power measurement is not responding" |
This error message indicates an internal software or hardware error. |
|
+704 "CDMA measurement failure; Frame error rate measurement is not responding" |
This error message indicates an internal software or hardware error. |
|
+705 "CDMA measurement failure; Access probe power measurement is not responding" |
This error message indicates an internal software or hardware error. |
|
+706 "CDMA measurement failure; Time response of open loop power control measurement is not responding" |
This error message indicates an internal software or hardware error. |
|
+707 "CDMA measurement failure; Gated power measurement is not responding" |
This error message indicates an internal software or hardware error. |
|
+708 "CDMA measurement failure; Tx spurious emissions measurement is not responding" |
This error message indicates an internal software or hardware error. |
|
+709 "CDMA measurement failure; Graphical access probe power measurement is not responding" |
This error message indicates an internal software or hardware error. |
|
+710 "CDMA measurement failure; Tx dynamic power measurement is not responding" |
This error message indicates an internal software or hardware error. |
|
+713 CDMA measurement failure; Fast Device Tune measurement is not responding. |
|
|
+712 "CDMA measurement failure; Multi-tone audio measurement is not responding" |
This error message indicates an internal software or hardware error. |
|
+721 "CDMA measurement failure; Gated power measurement requires MS to transmit in eighth traffic data rate (gated mode). Verify loopback service option and eighth traffic data rate" |
Select an IS-95 loopback service option using the Service Option (F12) key, or select an IS-2000 radio configuration 1 or 2 loopback service option using the FCH Service Option Setup (F12) key. Select "Eighth" in the Traffic Data Rate field before attempting Gated Power measurements. |
|
+726 "CDMA measurement failure; Time response of open loop power control measurement requires MS to transmit in non-gated mode. Verify loopback service option and full traffic data rate" |
Select an IS-95 loopback service option using the Service Option (F12) key, or select an IS-2000 radio configuration 1 or 2 loopback service option using the FCH Service Option Setup (F12) key. |
|
+727 "CDMA measurement failure; Time response of open loop power control measurement requires receiver power control set to auto" |
See Automatic Receiver Control to set receiver power control to auto. |
|
+728 "CDMA measurement failure; Time response of open loop power control measurement requires receiver power to be within range before and after the measurement" |
See Automatic Receiver Control . |
|
+729 "CDMA measurement failure; Time response of open loop power control measurement requires cell power to be within range before and after the measurement" |
See CALL[:CELL[1]]:POWer[:SAMPlitude][:SELected] for power range. |
|
+730 "CDMA measurement failure; Time response of open loop power control measurement requires AWGN state off" |
See CALL:AWGNoise[:INTernal]:POWer:STATe<[:SELected]|:DIGital2000|:DIGital95> . |
|
+731 "CDMA measurement failure; Time response of open loop power control measurement requires cell 2 power state off" |
See CALL:CELL2:POWer:STATe[:SELected] . |
|
+736 "CDMA measurement failure; Graphical access probe power measurement requires call status idle" |
See Graphical Access Probe Power Measurement Description . |
|
+738 "CDMA measurement warning; Frame error rate measurement may be failed when F-FCH/traffic frame pattern good frames less than 3 and F-FCH/traffic frame pattern state is on" |
See FER Measurement Specific to the Lab Application . |
|
+741 "CDMA measurement failure; TX dynamic power measurement requires receiver power control set to manual" |
See TX Dynamic Power Measurement Description . |
|
+746 "CDMA measurement failure; Max/min power measurement requires cell power, pilot, and traffic/F-FCH states on" |
See Maximum/Minimum Power Measurement Description . |
|
+747 "CDMA measurement failure; Max/min power measurement requires AWGN state off" |
See Maximum/Minimum Power Measurement Description . |
|
+748 "CDMA measurement failure; Max/min power measurement requires cell 2 power state off" |
See Maximum/Minimum Power Measurement Description . |
|
+749 "CDMA measurement failure; Max/min power measurement max cell power, pilot level, and traffic/F-FCH level are incompatible" |
See Maximum/Minimum Power Measurement Description . |
|
+750 "CDMA measurement failure; Max/min power measurement min cell power, pilot level, and traffic/F-FCH level are incompatible" |
See Maximum/Minimum Power Measurement Description . |
|
+754 "Data out of range; Multi-tone audio downlink total level upper limit exceeded; no change" |
See Multi-Tone Audio Measurement Description . |
|
+755 "Data out of range; Multi-tone audio uplink total level upper limit exceeded; no change" |
See Multi-Tone Audio Measurement Description . |
|
+757 "CDMA measurement operation rejected; Multi-tone audio downlink levels cannot be set" |
See Multi-Tone Audio Measurement Description . |
|
+758 "CDMA measurement operation rejected; Multi-tone audio uplink levels cannot be set when total level state is on" |
See Multi-Tone Audio Measurement Description . |
|
+759 "CDMA measurement operation rejected; Multi-tone audio analyzer frequencies cannot be set when use generator frequencies state is on" |
See Multi-Tone Audio Measurement Description . |
|
+760 "CDMA measurement warning; Multi-tone audio downlink level over range due to requested setting" |
See Multi-Tone Audio Measurement Description . |
|
+761 "CDMA measurement warning; Multi-tone audio measurement not compatible with service option 3 (EVRC)" |
See Multi-Tone Audio Measurement Description . |
|
+780 CDMA measurement failure; Fast Device Tune measurement setup is not correct. Refer to your documentation CD or go to www.keysight.com/find/8960 for correct setup steps |
|
|
+781 CDMA operation rejected; Fast Device Tune feature is not licensed. See www.keysight.com/find/8960upgrades for additional information |
|
| +782 CDMA measurement failure; Fast Device Tune measurement MS Tx/Rx frequency step sequence table start index + frequency step count must be less than or equal to 40 | |
|
+783 CDMA measurement failure; Fast Device Tune measurement MS Tx/Rx power step sequence table start index + power step count must be less than or equal to 40 |
|
|
+784 CDMA measurement failure; Fast Device Tune measurement MS Tx/Rx frequency values in use must not be NAN |
|
|
+785 CDMA measurement failure; Fast Device Tune measurement MS Tx/Rx power levels in use must be not NAN |
|
|
+786 CDMA measurement failure; Fast Device Tune measurement MS Tx frequency values in use are not in the same band |
|
|
+787 CDMA measurement failure; Fast Device Tune measurement MS Rx frequency values in use are not in the same band |
|
|
+788 CDMA measurement failure; Fast Device Tune measurement MS Tx power levels in use are out of range |
|
|
+789 CDMA measurement failure; Fast Device Tune measurement MS Rx power levels in use are out of range. |
|
|
+790 CDMA measurement failure; Fast Device Tune measurement unable to build frequency and power sequence tables. Measurement is unavailable. Check the Message Log for error details |
|
| +792 CDMA measurement failure; Fast Device Tune measurement first frequency in frequency sequence not in recognized frequency band | |
|
+796 CDMA call processing error; SMS mobile originated message received. SMS not supported by base station due to current SMS receive protocol (network failure) |