SETup:AAUDio

SETup:AAUDio

Last updated: May 31, 2010

GPIB Command Conventions

SETup:AAUDio:CONTinuous

Function	GSM TA	Selects/queries the trigger arm state for Analog Audio measurements.
	GSM/GPRS LA
	EGPRS LA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS TA	This command is not applicable to EGPRS.
Setting		Range: Continuous trigger arm mode = 1 \| ON Single trigger arm mode = 0 \| OFF
Query		Range: 0 \| 1
*RST setting		Single \| 0 \| OFF
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETUP:AAUDIO:CONTINUOUS OFF" ! Selects single trigger mode.

SETup:AAUDio:COUNt[:SNUMber]

Function	GSM TA	Selects the number of Analog Audio multi-measurements the test set will make and sets the count state to ON.
	GSM/GPRS LA
	EGPRS LA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS TA	This command is not applicable to EGPRS.
Setting		Range: 1 to 999 Resolution: 1
Query		Range: 1 to 999 Resolution: 1
*RST setting		10
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETUP:AAUDIO:COUNT:SNUMBER 5" ! Sets the value to 5 and the state to on.

SETup:AAUDio:COUNt:NUMBer

Function	GSM TA	Selects/queries the number of Analog Audio measurements the test set will make when the SETup:AAUDio:COUNt:STATe is ON.
	GSM/GPRS LA
	EGPRS LA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS TA	This command is not applicable to EGPRS.
Setting		Range: 1 to 999 Resolution: 1
Query		Range: 1 to 999 Resolution: 1
*RST setting		10
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"ABORT:ALL" !Aborts all active measurements in progress. OUTPUT 714;"SETUP:AAUDIO:COUNT:NUMBER 10" ! Sets the audio multi-measurement count number to 10.

SETup:AAUDio:COUNt:STATe

Function	GSM TA	Selects/queries the Analog Audio multi-measurement count state.
	GSM/GPRS LA
	EGPRS LA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS TA	This command is not applicable to EGPRS.
Setting		Range: 1 \| ON \| 0 \| OFF
Query		Range: 1 \| 0
*RST setting		0 \| OFF
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETUP:AAUDIO:COUNT:STATE ON" ! Turns the analog audio measurement multi-measurement count state on.

SETup:AAUDIO:DEMPhasis:STATe

Function	GSM TA	Sets/queries whether 750 us de-emphasis is enabled.
	GSM/GPRS LA
	EGPRS LA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS TA	This command is not applicable to EGPRS.
Setting		Range: 1 \| ON \| 0 \| OFF
Query		Range: 1 \| 0
*RST setting		0 \| OFF
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETUP:AAUDIO:DEMPhasis:STATE ON" ! Turns the de-emphasis on.

SETup:AAUDio:DETector[:TYPE]

Function	GSM TA	Sets/queries the detector type for audio level measurements.
	GSM/GPRS LA
	EGPRS LA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS TA	This command is not applicable to EGPRS.
Setting		Range: RMS \| PEAK
Query		Range: RMS \| PEAK
*RST setting		RMS
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETUP:AAUDIO:DETECTOR:TYPE PEAK"

SETup:AAUDio:EXPANDOR[:SRLevel]

Function	GSM TA	Sets/queries the expandor's reference level and automatically sets the expandor's state to ON. The units (V\|MV\|UV) are optional, if no units are specified then units default to V.
	GSM/GPRS LA
	EGPRS LA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS TA	This command is not applicable to EGPRS.
Setting		Range: 10 mV to 10 V Resolution: 1 mV
Query		Range: 10 mV to 10 V Resolution: 1 mV
*RST setting		1 V
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETUP:AAUDIO:EXPANDOR:SRLEVEL 5V" ! Sets expandor state to on and level to 5 V.

SETup:AAUDio:EXPANDOR:RLEVel

Function	GSM TA	Sets/queries the expandor's reference level to be used when the expandor's state is set to ON. The units (V\|MV\|UV) are optional, if no units are specified then units default to V.
	GSM/GPRS LA
	EGPRS LA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS TA	This command is not applicable to EGPRS.
Setting		Range: 10 mV to 10 V Resolution: 1 mV
Query		Range: 10 mV to 10 V Resolution: 1 mV
*RST setting		1 V
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETUP:AAUDIO:EXPANDOR:RLEVEL 5V" ! Sets expandor reference level to 5 V.

SETup:AAUDio:EXPANDOR:STATe

Function	GSM TA	Sets/queries whether the expandor is enabled.
	GSM/GPRS LA
	EGPRS LA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS TA	This command is not applicable to EGPRS.
Setting		Range: 1 \| ON \| 0 \| OFF
Query		Range: 1 \| 0
*RST setting		0 \| OFF
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETUP:AAUDIO:EXPANDOR:STATE ON"

SETup:AAUDio:EXPected:VOLTage[:PEAK]

Function	GSM TA	Sets/queries the maximum expected peak voltage (clipping level) of the Analog Audio signal to be measured. The units (V\|MV\|UV) are optional, if no units are specified then units default to V. See SETup:AAUDio .
	GSM/GPRS LA
	EGPRS LA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS TA	This command is not applicable to EGPRS.
Setting		Range: 10 mV to 20 V peak Resolution: 0.1 mV
Query		Range: 10 mV to 20 V peak Resolution: 0.1 mV
*RST setting		20 V
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETUP:AAUDIO:EXPECTED:VOLTAGE 5V" ! Sets the clipping level of Analog Audio measurements to 5 volts.

SETup:AAUDio:FILTer[:SFRequency]

Function	GSM TA	Sets/queries the center frequency for the 100 Hz bandpass filter applied to Analog Audio measurements and sets the state to on. Units (KHZ\|HZ) are optional, if no units are specified then units default to Hz.
	GSM/GPRS LA
	EGPRS LA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS TA	This command is not applicable to EGPRS.
Setting		Range: 200 Hz to 20.0 kHz Resolution: 0.1 Hz
Query		Range: 200 Hz to 20.0 kHz Resolution: 0.1 Hz
*RST setting		1000 Hz
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETUP:AAUDIO:FILTER:SFREQUENCY 1000" ! This sets the aaudio filter state to on and sets the bandpass filter frequency to 1 kHz.

SETup:AAUDio:FILTer:FREQuency

Function	GSM TA	Sets/queries the center frequency for the 100 Hz bandpass filter applied to Analog Audio measurements. Units (KHZ\|HZ) are optional, if no units are specified then units default to Hz. See SETup:AAUDio .
	GSM/GPRS LA
	EGPRS LA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS TA	This command is not applicable to EGPRS.
Setting		Range: 200 Hz to 20.0 kHz Resolution: 0.1 Hz
Query		Range: 200 Hz to 20.0 kHz Resolution: 0.1 Hz
*RST setting		1000 Hz
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETUP:AAUDIO:FILTER:FREQUENCY 217HZ" ! Set aaudio bandpass filter to 217 hz.

SETup:AAUDio:FILTer:STATe

Function	GSM TA	Selects/queries the state of the Analog Audio bandpass filter. see SETup:AAUDio
	GSM/GPRS LA
	EGPRS LA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS TA	This command is not applicable to EGPRS.
Setting		Range: 1 \| ON \| 0 \| OFF
Query		Range: 1 \| 0
*RST setting		0 (off)
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETUP:AAUDIO:FILTER:STATE ON" ! Sets filter state on.

SETup:AAUDio:FILTer:TYPE

Function	GSM TA	Sets/queries the filter type for audio measurements.
	GSM/GPRS LA
	EGPRS LA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS TA	This command is not applicable to EGPRS.
Setting		Range: NONE \| TBPass \| CMESsage \| BPASs50 \| BPASs300
Query		Range: NONE \| TBP \| CMES \| BPAS50 \| BPAS300
*RST setting		NONE
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETUP:AAUDIO:FILTER:TYPE BPASS50" ! Selects the 50 Hz to 15 kHz bandpass filter.

SETup:AAUDio:FREQuency:STATe

Function	GSM TA	Sets/queries whether the audio frequency measurement is enabled.
	GSM/GPRS LA
	EGPRS LA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS TA	This command is not applicable to EGPRS.
Setting		Range: 1 \| ON \| 0 \| OFF
Query		Range: 1 \| 0
*RST setting		0 \| OFF
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETUP:AAUDIO:FREQUENCY:STATE ON"

SETup:AAUDio:SDIStortion:FREQuency

Function	GSM TA	Sets/queries the fundamental frequency setting for the SINAD/distortion measurement. Units (KHZ\|HZ) are optional, if no units are specified then units default to Hz.
	GSM/GPRS LA
	EGPRS LA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS TA	This command is not applicable to EGPRS.
Setting		Range: 100.0 to 10000 Hz Resolution: 0.1 Hz
Query		Range: 100.0 to 10000 Hz Resolution: 0.1 Hz
*RST setting		1000 Hz
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;SETUP:AAUDIO:SDISTORTION:FREQUENCY 300HZ"

SETup:AAUDio:SDIStortion:STATe

Function	GSM TA	Sets/queries whether the SINAD/distortion measurement is enabled.
	GSM/GPRS LA
	EGPRS LA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS TA	This command is not applicable to EGPRS.
Setting		Range: 1 \| ON \| 0 \| OFF
Query		Range: 1 \| 0
*RST setting		0 \| OFF
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example 10 OUTPUT 714;SETUP:AAUDIO:SDISTORTION:STATE ON"

SETup:AAUDio:TIMEout[:STIME]

Function	GSM TA	Selects/queries the timeout value in seconds that will be used for Analog Audio measurements and sets the timeout state to ON. Units (S\|MS) are optional, if no units are specified then units default to S.
	GSM/GPRS LA
	EGPRS LA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS TA	This command is not applicable to EGPRS.
Setting		Range: 0.1 to 999.9 seconds Resolution: 0.1 seconds
Query		Range: 0.1 to 999.9 seconds Resolution: 0.1 seconds
*RST setting		10 seconds
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETUP:AAUDIO:TIMEOUT:STIME 3" ! Sets the timeout state to on and sets the timeout value.

SETup:AAUDio:TIMEout:STATe

Function	GSM TA	Selects/queries the Analog Audio measurement timeout state.
	GSM/GPRS LA
	EGPRS LA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS TA	This command is not applicable to EGPRS.
Setting		Range: 1 \| ON \| 0 \| OFF
Query		Range: 1 \| 0
*RST setting		0 \| OFF
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETUP:AAUDIO:TIMEOUT:STATE ON" ! Sets timeout state to on.

SETup:AAUDio:TIMEout:TIME

Function	GSM TA	Selects/queries the timeout value in seconds that will be used for Analog Audio measurements when the timeout state is ON. Unit (S\|MS) are optional, if no units are specified then units default to S.
	GSM/GPRS LA
	EGPRS LA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS TA	This command is not applicable to EGPRS.
Setting		Range: 0.1 to 999.9 seconds Resolution: 0.1 seconds
Query		Range: 0.1 to 999.9 seconds Resolution: 0.1 seconds
*RST setting		10 seconds
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETUP:AAUDIO:TIMEOUT:TIME 5" ! Sets timeout value to 5 seconds.