SETup:ORFSpectrum

Function

GSM

This command selects/queries the trigger state for output RF spectrum measurements in the active (that is the selected) format.

GPRS

Range:

• Continuous trigger mode = 1|ON
• Single trigger mode = 0|OFF

Query

Range: 1|0

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"ABORT:ALL" !Aborts all active measurements in progress.

 
OUTPUT 714;"SETUP:CONTINUOUS OFF" !Sets trigger mode to single for an ORFS measurement.

Function

GSM

This command is not applicable to GSM.

GPRS

This command selects/queries the trigger state for output RF spectrum measurements in the GPRS format whether or not that format is active.

Range:

• Continuous trigger mode = 1|ON
• Single trigger mode = 0|OFF

Query

Range: 1|0

Programming Example

 
OUTPUT 714;"ABORT:ALL" !Aborts all active measurements in progress.

 
OUTPUT 714;"SETUP:CONTINUOUS:GPRS OFF" !Sets trigger mode to single for an ORFS measurement.

Function

GSM

This command selects/queries the trigger state for output RF spectrum measurements in the GSM format whether or not that format is active.

GPRS

This command is not applicable to GPRS.

Range:

• Continuous trigger mode = 1|ON
• Single trigger mode = 0|OFF

Query

Range: 1|0

Programming Example

 
OUTPUT 714;"ABORT:ALL" !Aborts all active measurements in progress.

 
OUTPUT 714;"SETUP:CONTINUOUS:GSM OFF" !Sets trigger mode to single for an ORFS measurement.

Function

GSM

This command selects/queries the ORFS due to switching and modulation multi-measurement count state in the active (that is the selected) format.

GPRS

Range: 0|OFF|1|ON

Query

Range: 0|1

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:COUNT:STATE ON" 
!Sets count state for both ORFS due to switching and modulation measurements.

Function

GSM

This command is not applicable to GSM.

GPRS

This command selects/queries the ORFS due to switching and modulation multi-measurement count state in the GPRS format whether or not that format is active.

Range: 0|OFF|1|ON

Query

Range: 0|1

1 (on)

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:COUNT:STATE:GPRS ON" 
!Sets count state for both ORFS due to switching and modulation measurements.

Function

GSM

This command selects/queries the ORFS due to switching and modulation multi-measurement count state in the GSM format whether or not that format is active.

GPRS

This command is not applicable to GPRS.

Range: 0|OFF|1|ON

Query

Range: 0|1

1 (on)

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:COUNT:STATE:GSM ON" 
!Sets count state for both ORFS due to switching and modulation measurements.

Function

GSM

This command queries the total number of measurements made each time an ORFS measurement is initiated in the active (that is the selected) format. This number will vary depending on the number of offsets and number of multi-measurements that you choose.

The total number of measurements is calculated using the following formula:

ICO MAX = 1 + M + S

• Where:

  • M= ( the number of modulation offsets ) ¥ ( the number of multi-measurements for ORFS due to modulation ).

  • S= ( the number of switching offsets ) ¥ ( the number of multi-measurements for ORFS due to switching ) .

See Output RF Spectrum Measurement Description for a description of modulation and switching offsets.

GPRS

Query

Range: 1 to 29971

Resolution: 1

Function

GSM

This command is not applicable to GSM

GPRS

This command queries the total number of measurements made each time an ORFS measurement is initiated in the GPRS format whether or not that format is active. This number will vary depending on the number of offsets and number of multi-measurements that you choose.

The total number of measurements is calculated using the following formula:

ICO MAX = 1 + M + S

• Where:

  • M= ( the number of modulation offsets ) ¥ ( the number of multi-measurements for ORFS due to modulation ).

  • S= ( the number of switching offsets ) ¥ ( the number of multi-measurements for ORFS due to switching ) .

See Output RF Spectrum Measurement Description for a description of modulation and switching offsets.

Query

Range: 1 to 29971

Resolution: 1

Function

GSM

This command queries the total number of measurements made each time an ORFS measurement is initiated in the GSM format whether or not that format is active. This number will vary depending on the number of offsets and number of multi-measurements that you choose.

The total number of measurements is calculated using the following formula:

ICO MAX = 1 + M + S

• Where:

  • M= ( the number of modulation offsets ) ¥ ( the number of multi-measurements for ORFS due to modulation ).

  • S= ( the number of switching offsets ) ¥ ( the number of multi-measurements for ORFS due to switching ) .

See Output RF Spectrum Measurement Description for a description of modulation and switching offsets.

GPRS

This command is not applicable to GPRS.

Query

Range: 1 to 29971

Resolution: 1

Function

GSM

This command selects whether the ORFS measurement uses the ETSI defined limits or those which you can set using the commands: SETup:ORFSpectrum:MODulation:LIMit:MANual[:SELected][:SELected] and SETup:ORFSpectrum:SWITching:LIMit:MANual[:SELected][:SELected] .
This command is implemented in the active (that is the selected) format.

GPRS

Range: ETSI | MANual

Query

Range: ETSI | MAN

Programming Example

 
OUTPUT 714"SETUP:ORFSPECTRUM:LIMIT:SOURCE MAN" 
!Allows you to manually set the limits.

Function

GSM

This command is not applicable to GSM.

GPRS

This command selects whether the ORFS measurement uses the ETSI defined limits or those which you can set using the commands: SETup:ORFSpectrum:MODulation:LIMit:MANual[:SELected][:SELected] and SETup:ORFSpectrum:SWITching:LIMit:MANual[:SELected][:SELected] .
This command is implemented in the GPRS format whether or not that format is active.

Range: ETSI | MANual

Query

Range: ETSI | MAN

Programming Example

 
OUTPUT 714"SETUP:ORFSPECTRUM:LIMIT:SOURCE MAN" 
!Allows you to manually set the limits.

Function

GSM

This command selects whether the ORFS measurement uses the ETSI defined limits or those which you can set using the commands: SETup:ORFSpectrum:MODulation:LIMit:MANual[:SELected][:SELected] and SETup:ORFSpectrum:SWITching:LIMit:MANual[:SELected][:SELected] .
This command is implemented in the GSM format whether or not that format is active.

GPRS

This command is not applicable to GPRS.

Range: ETSI | MANual

Query

Range: ETSI | MAN

Programming Example

 
OUTPUT 714"SETUP:ORFSPECTRUM:LIMIT:SOURCE MAN" 
!Allows you to manually set the limits.

Function

GSM

This command sets/queries the number of ORFS due to modulation multi-measurements the test set will make in the active (that is the selected) format. This command sets the count state to ON.

GPRS

Range: 1 to 999

Resolution: 1

Query

Range: 1 to 999

Resolution: 1

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714"SETUP:ORFSPECTRUM:MODULATION:COUNT:SNUMBER 99" 
!Sets the value to 99 multi-measurements and the state to on.

Function

GSM

This command is not applicable to GSM.

GPRS

This command sets/queries the number of ORFS due to modulation multi-measurements the test set will make in the GPRS format whether or not that format is active. This command sets the count state to ON.

Range: 1 to 999

Resolution: 1

Query

Range: 1 to 999

Resolution: 1

20

Programming Example

 
OUTPUT 714"SETUP:ORFSPECTRUM:MODULATION:COUNT:GPRS 99" 
!Sets the value to 99 multi-measurements and the state to on.

Function

GSM

This command sets/queries the number of ORFS due to modulation multi-measurements the test set will make in the GSM format whether or not that format is active. This command sets the count state to ON.

GPRS

This command is not applicable to GPRS.

Range: 1 to 999

Resolution: 1

Query

Range: 1 to 999

Resolution: 1

20

Programming Example

 
OUTPUT 714"SETUP:ORFSPECTRUM:MODULATION:COUNT:GSM 99" 
!Sets the value to 99 multi-measurements and the state to on.

Function

GSM

GPRS

Range: 1 to 999

Resolution: 1

Query

Range: 1 to 999

Resolution: 1

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:MODULATION:COUNT:NUMBER 75" 
!Sets the multi-measurement count number for ORFS due to modulation measurements to 75.

Function

GSM

GPRS

Range: 1 to 999

Resolution: 1

Query

Range: 1 to 999

Resolution: 1

20

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:MODULATION:COUNT:NUMBER:GPRS 75" 
!Sets the multi-measurement count number for ORFS due to modulation measurements to 75.

Function

GSM

GPRS

This command is not applicable to GPRS.

Range: 1 to 999

Resolution: 1

Query

Range: 1 to 999

Resolution: 1

20

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:MODULATION:COUNT:NUMBER:GSM 75" 
!Sets the multi-measurement count number for ORFS due to modulation measurements to 75.

Function

GSM

GPRS

Range: 0 to 22 comma-separated values ranging from -1.8 MHz to -10 Hz, and +10 Hz to +1.8 MHz

Resolution: 10 Hz

Query

Range: 0 to 22 comma-separated values ranging from -1.8 MHz to -10 Hz, and +10 Hz to +1.8 MHz

Resolution: 10 Hz

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:MODULATION:FREQUENCY:OFFSET 400 KHZ, 700 KHZ" 
!Turns on the first two ORFS due to modulation measurement offsets and sets
!them to 400 kHz and 700 kHz offsets. All other offsets are in the off state.

OUTPUT 714;"SETUP:ORFSPECTRUM:MODULATION:FREQUENCY:OFFSET 700 KHZ" 
!Turns on the first ORFS due to modulation measurement offset and sets it to  A 700 kHz
!offset. All other offsets are in the off state.

OUTPUT 714;"SETUP:ORFSPECTRUM:MODULATION:FREQUENCY:OFFSET" 
!Turns all offsets for ORFS due to modulation measurement to the off state.

Function

GSM

This command is not applicable to GSM.

GPRS

This command sets/queries the list of ORFS due to modulation frequency offsets in the GPRS format whether or not that format is active. Each offset listed in the command is turned on by default. If no frequency offsets (null list) are sent, the output RF spectrum due to modulation measurement will not be made. The units (GHZ|MHZ|KHZ|HZ) are optional, if no units are specified than units default to HZ. see Output RF Spectrum Measurement Description

Range: 0 to 22 comma-separated values ranging from -1.8 MHz to -10 Hz, and +10 Hz to +1.8 MHz

Resolution: 10 Hz

Query

Range: 0 to 22 comma-separated values ranging from -1.8 MHz to -10 Hz, and +10 Hz to +1.8 MHz

Resolution: 10 Hz

Offset 1: 400.0 kHz

Offset 2: 600.0 kHz

Offsets 3 to 22: off

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:MODULATION:FREQUENCY:OFFSET:GPRS 400 KHZ, 700 KHZ" 
!Turns on the first two ORFS due to modulation measurement offsets and sets
!them to 400 kHz and 700 kHz offsets. All other offsets are in the off state.

OUTPUT 714;"SETUP:ORFSPECTRUM:MODULATION:FREQUENCY:OFFSET:GPRS 700 KHZ" 
!Turns on the first ORFS due to modulation measurement offset and sets it to  A 700 kHz
!offset. All other offsets are in the off state.

OUTPUT 714;"SETUP:ORFSPECTRUM:MODULATION:FREQUENCY:OFFSET:GPRS" 
!Turns all offsets for ORFS due to modulation measurement to the off state.

Function

GSM

This command sets/queries the list of ORFS due to modulation frequency offsets in the GSM format whether or not that format is active. Each offset listed in the command is turned on by default. If no frequency offsets (null list) are sent, the output RF spectrum due to modulation measurement will not be made. The units (GHZ|MHZ|KHZ|HZ) are optional, if no units are specified than units default to HZ. see Output RF Spectrum Measurement Description

GPRS

This command is not applicable to GPRS.

Range: 0 to 22 comma-separated values ranging from -1.8 MHz to -10 Hz, and +10 Hz to +1.8 MHz

Resolution: 10 Hz

Query

Range: 0 to 22 comma-separated values ranging from -1.8 MHz to -10 Hz, and +10 Hz to +1.8 MHz

Resolution: 10 Hz

Offset 1: 400.0 kHz

Offset 2: 600.0 kHz

Offsets 3 to 22: off

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:MODULATION:FREQUENCY:OFFSET:GSM 400 KHZ, 700 KHZ" 
!Turns on the first two ORFS due to modulation measurement offsets and sets
!them to 400 kHz and 700 kHz offsets. All other offsets are in the off state.

OUTPUT 714;"SETUP:ORFSPECTRUM:MODULATION:FREQUENCY:OFFSET:GSM 700 KHZ" 
!Turns on the first ORFS due to modulation measurement offset and sets it to  A 700 kHz
!offset. All other offsets are in the off state.

OUTPUT 714;"SETUP:ORFSPECTRUM:MODULATION:FREQUENCY:OFFSET:GSM" 
!Turns all offsets for ORFS due to modulation measurement to the off state.

Function

GSM

This command queries the number of frequency offsets currently on during an ORFS due to modulation measurement in the active (that is the selected) format. See Output RF Spectrum Measurement Description .

GPRS

Query

Range: 0 to 22

Resolution: 1

Function

GSM

This command is not applicable to GSM.

GPRS

This command queries the number of frequency offsets currently on during an ORFS due to modulation measurement in the GPRS format whether or not that format is active. See Output RF Spectrum Measurement Description .

Query

Range: 0 to 22

Resolution: 1

Function

GSM

This command queries the number of frequency offsets currently on during an ORFS due to modulation measurement in the GSM format whether or not that format is active. See Output RF Spectrum Measurement Description .

GPRS

This command is not applicable to GPRS

Query

Range: 0 to 22

Resolution: 1

Function

GSM

This command allows you to set the limits for the ORFS due to modulation measurement in the active (that is the selected) format. You can enter up to 22 limit values, one for each of the ORFS due to modulation offset frequencies. The n ^th limit value is the value for the n ^th offset frequency, regardless of whether the offset frequency is switched on or off. Changing the offset value has no effect on the limit value. If you supply fewer than 22 limit values, the remainder of the limit values remain unchanged.

The first optional [:SELected] node allows you to select which traffic channel band the setting is implemented in. The default band is the currently selected band, otherwise you can specify PGSM, EGSM, DCS, PCS, RGSM, GSM450, GSM480, GSM850, or GSM750.

GPRS

Range: 1 to 22 comma-separated values ranging from -200 dB to +100 dB

Resolution: 0.1

Query

Range: 22 comma-separated values ranging from -200 dB to +100 dB

Resolution: 0.1

Offset 1: -60 dB
Offset 2: -60 dB
Offset 3: +0.5 dB
Offset 4: +0.5 dB
Offset 5: -30 dB
Offset 6: -30 dB
Offset 7: -33 dB
Offset 8: -33 dB
Offset 9: -60 dB
Offset 10: -60 dB
Offset 11: -60 dB
Offset 12: -60 dB
Offset 13: -60 dB
Offset 14: -60 dB
Offset 15: -60 dB
Offset 16: -60 dB
Offset 17: -60 dB
Offset 18: -60 dB
Offset 19: -60 dB
Offset 20: -60 dB
Offset 21: -60 dB
Offset 22: -60 dB

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:MODULATION:LIMIT:MANUAL -58DB,-58DB" 
!Sets the first two offsets to -58 dB and -58 dB respectively.

Function

GSM

This command is not applicable to GSM.

GPRS

This command allows you to set the limits for the ORFS due to modulation measurement in the GPRS format whether or not that format is active. You can enter up to 22 limit values, one for each of the ORFS due to modulation offset frequencies. The n ^th limit value is the value for the n ^th offset frequency, regardless of whether the offset frequency is switched on or off. Changing the offset value has no effect on the limit value. If you supply fewer than 22 limit values, the remainder of the limit values remain unchanged.

The first optional [:SELected] node allows you to select which traffic channel band the setting is implemented in. The default band is the currently selected band, otherwise you can specify PGSM, EGSM, DCS, PCS, RGSM, GSM450, GSM480, GSM850, or GSM750.

Range: 1 to 22 comma-separated values ranging from -200 dB to +100 dB

Resolution: 0.1

Query

Range: 22 comma-separated values ranging from -200 dB to +100 dB

Resolution: 0.1

Offset 1: -60 dB
Offset 2: -60 dB
Offset 3: +0.5 dB
Offset 4: +0.5 dB
Offset 5: -30 dB
Offset 6: -30 dB
Offset 7: -33 dB
Offset 8: -33 dB
Offset 9: -60 dB
Offset 10: -60 dB
Offset 11: -60 dB
Offset 12: -60 dB
Offset 13: -60 dB
Offset 14: -60 dB
Offset 15: -60 dB
Offset 16: -60 dB
Offset 17: -60 dB
Offset 18: -60 dB
Offset 19: -60 dB
Offset 20: -60 dB
Offset 21: -60 dB
Offset 22: -60 dB

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:MODULATION:LIMIT:MANUAL:GPRS -58DB,-58DB" 
!Sets the first two offsets in the GPRS format to -58 dB and -58 dB respectively.

Function

GSM

This command allows you to set the limits for the ORFS due to modulation measurement in the GSM format whether or not that format is active. You can enter up to 22 limit values, one for each of the ORFS due to modulation offset frequencies. The n ^th limit value is the value for the n ^th offset frequency, regardless of whether the offset frequency is switched on or off. Changing the offset value has no effect on the limit value. If you supply fewer than 22 limit values, the remainder of the limit values remain unchanged.

The first optional [:SELected] node allows you to select which traffic channel band the setting is implemented in. The default band is the currently selected band, otherwise you can specify PGSM, EGSM, DCS, PCS, RGSM, GSM450, GSM480, GSM850, or GSM750.

GPRS

Range: 1 to 22 comma-separated values ranging from -200 dB to +100 dB

Resolution: 0.1

Query

Range: 22 comma-separated values ranging from -200 dB to +100 dB

Resolution: 0.1

Offset 1: -60 dB
Offset 2: -60 dB
Offset 3: +0.5 dB
Offset 4: +0.5 dB
Offset 5: -30 dB
Offset 6: -30 dB
Offset 7: -33 dB
Offset 8: -33 dB
Offset 9: -60 dB
Offset 10: -60 dB
Offset 11: -60 dB
Offset 12: -60 dB
Offset 13: -60 dB
Offset 14: -60 dB
Offset 15: -60 dB
Offset 16: -60 dB
Offset 17: -60 dB
Offset 18: -60 dB
Offset 19: -60 dB
Offset 20: -60 dB
Offset 21: -60 dB
Offset 22: -60 dB

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:MODULATION:LIMIT:MANUAL:GSM -58DB,-58DB" 
!Sets the first two offsets in the GSM format to -58 dB and -58 dB respectively.

Function

GSM

This command sets/queries the ORFS due to switching multi-measurement count value and turns the state on in the active (that is the selected) format.

GPRS

Range: 1 to 999

Resolution: 1

Query

Range: 1 to 999

Resolution: 1

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:COUNT:SNUMBER 55" 
!Sets the multi-measurment value to 10 and the state to on.

Function

GSM

This command is not applicable to GSM.

GPRS

This command sets/queries the ORFS due to switching multi-measurement count value and turns the state on in the GPRS format whether or not that format is active.

Range: 1 to 999

Resolution: 1

Query

Range: 1 to 999

Resolution: 1

10

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:COUNT:SNUMBER:GPRS 55" 
!Sets the multi-measurment value to 10 and the state to on.

Function

GSM

This command sets/queries the ORFS due to switching multi-measurement count value and turns the state on in the GSM format whether or not that format is active.

GPRS

This command is not applicable to GPRS

Range: 1 to 999

Resolution: 1

Query

Range: 1 to 999

Resolution: 1

10

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:COUNT:SNUMBER:GSM 55" 
!Sets the multi-measurment value to 10 and the state to on.

Function

GSM

GPRS

Range: 1 to 999

Resolution: 1

Query

Range: 1 to 999

Resolution: 1

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:COUNT:NUMBER 15" 
!Sets the multi-measurement count number for ORFS due to switching to 15.

Function

GSM

This command is not applicable to GSM

GPRS

This command sets/queries the ORFS due to switching multi-measurement count value in the GPRS format whether or not that format is active. See Output RF Spectrum Measurement Description

Range: 1 to 999

Resolution: 1

Query

Range: 1 to 999

Resolution: 1

10

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:COUNT:NUMBER:GPRS 15" 
!Sets the multi-measurement count number for ORFS due to switching to 15.

Function

GSM

This command sets/queries the ORFS due to switching multi-measurement count value in the GSM format whether or not that format is active. See Output RF Spectrum Measurement Description

GPRS

This command is not applicable to GPRS.

Range: 1 to 999

Resolution: 1

Query

Range: 1 to 999

Resolution: 1

10

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:COUNT:NUMBER:GSM 15" 
!Sets the multi-measurement count number for ORFS due to switching to 15.

Function

GSM

GPRS

Range: 0 to 8 comma-separated values ranging from -1.8 MHz to -10 Hz, and +10 Hz to +1.8 MHz

Resolution: 10 Hz

Query

Range: 0 to 8 comma-separated values ranging from -1.8 MHz to -10 Hz, and +10 Hz to +1.8 MHz

Resolution: 10 Hz

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:FREQUENCY:OFFSET 400 KHZ, 700 KHZ" 
!Turns on the first two ORFS due to switching measurement offsets and sets them
!to 400 kHz and 700 kHz offsets. All other offsets are in the off state.

OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:FREQUENCY:OFFSET 700 KHZ" 
!Turns on the first ORFS due to switching measurement offset and sets it to 700 kHz
!offsets. All other offsets are in the off state.

OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:FREQUENCY:OFFSET" 
!Turns all of the ORFS due to switching measurements offsets to off.

Function

GSM

GPRS

This command sets/queries the list of ORFS due to switching frequency offsets in the GPRS format whether or not that format is active. Each offset listed in the command is turned on by default. If no frequency offsets (null list) are sent, the output RF spectrum due to switching measurement will not be made. The units (GHZ|MHZ|KHZ|HZ) are optional, if no units are specified than units default to HZ. See Output RF Spectrum Measurement Description .

Range: 0 to 8 comma-separated values ranging from -1.8 MHz to -10 Hz, and +10 Hz to +1.8 MHz

Resolution: 10 Hz

Query

Range: 0 to 8 comma-separated values ranging from -1.8 MHz to -10 Hz, and +10 Hz to +1.8 MHz

Resolution: 10 Hz

Offset 1 = 400.0 kHz

Offset 2 = 600.0 kHz

Offsets 3 to 8 off

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:FREQUENCY:OFFSET:GPRS 400 KHZ, 700 KHZ" 
!Turns on the first two ORFS due to switching measurement offsets and sets them
!to 400 kHz and 700 kHz offsets. All other offsets are in the off state.

OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:FREQUENCY:OFFSET:GPRS 700 KHZ" 
!Turns on the first ORFS due to switching measurement offset and sets it to 700 kHz
!offsets. All other offsets are in the off state.

OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:FREQUENCY:OFFSET:GPRS" 
!Turns all of the ORFS due to switching measurements offsets to off.

Function

GSM

This command sets/queries the list of ORFS due to switching frequency offsets in the GSM format whether or not that format is active. Each offset listed in the command is turned on by default. If no frequency offsets (null list) are sent, the output RF spectrum due to switching measurement will not be made. The units (GHZ|MHZ|KHZ|HZ) are optional, if no units are specified than units default to HZ. See Output RF Spectrum Measurement Description .

GPRS

This command is not applicable to GPRS.

Range: 0 to 8 comma-separated values ranging from -1.8 MHz to -10 Hz, and +10 Hz to +1.8 MHz

Resolution: 10 Hz

Query

Range: 0 to 8 comma-separated values ranging from -1.8 MHz to -10 Hz, and +10 Hz to +1.8 MHz

Resolution: 10 Hz

Offset 1 = 400.0 kHz

Offset 2 = 600.0 kHz

Offsets 3 to 8 off

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:FREQUENCY:OFFSET:GSM 400 KHZ, 700 KHZ" 
!Turns on the first two ORFS due to switching measurement offsets and sets them
!to 400 kHz and 700 kHz offsets. All other offsets are in the off state.

OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:FREQUENCY:OFFSET:GSM 700 KHZ" 
!Turns on the first ORFS due to switching measurement offset and sets it to 700 kHz
!offsets. All other offsets are in the off state.

OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:FREQUENCY:OFFSET:GSM" 
!Turns all of the ORFS due to switching measurements offsets to off.

Function

GSM

GPRS

Query

Range: 0 to 8

Resolution: 1

Function

GSM

GPRS

This command queries the number of frequency offsets currently on during an ORFS due to switching measurement in the GPRS format whether or not that format is active. See Output RF Spectrum Measurement Description .

Query

Range: 0 to 8

Resolution: 1

Function

GSM

This command queries the number of frequency offsets currently on during an ORFS due to switching measurement in the GSM format whether or not that format is active. See Output RF Spectrum Measurement Description .

GPRS

This command is not applicable to GPRS.

Query

Range: 0 to 8

Resolution: 1

Function

GSM

This command allows you to set the limits for the ORFS due to switching measurement in the active (that is the selected) format. You can enter up to eight limit values, one for each of the ORFS due to switching offset frequencies. The n ^th limit value is the value for the n ^th offset frequency, regardless of whether the offset frequency is switched on or off. Changing the offset value has no effect on the limit value. If you supply fewer than eight limit values, the remainder of the limit values remain unchanged.

The first optional [:SELected] node allows you to select which traffic channel band the setting is implemented in. The default band is the currently selected band, otherwise you can specify PGSM, EGSM, DCS, PCS, RGSM, GSM450, GSM480, GSM850, or GSM750.

GPRS

Range: 1 to 8 comma-separated values ranging from -200 dBm to +100 dBm

Resolution: 0.1

Query

Range:8 comma-separated values ranging from -200 dBm to +100 dBm

Resolution: 0.1

Offset 1: -23 dBm
Offset 2: -26 dBm
Offset 3: -23 dBm
Offset 4: -26 dBm
Offset 5: -32 dBm
Offset 6: -32 dBm
Offset 7: -36 dBm
Offset 8: -36 dBm

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:LIMIT:MANUAL -30DBM,-32DBM" 
!Sets the first two offsets to -30 dBm and -32 dBm respectively.

Function

GSM

GPRS

This command allows you to set the limits for the ORFS due to switching measurement in the in the GPRS format whether or not that format is active. You can enter up to eight limit values, one for each of the ORFS due to switching offset frequencies. The n ^th limit value is the value for the n ^th offset frequency, regardless of whether the offset frequency is switched on or off. Changing the offset value has no effect on the limit value. If you supply fewer than eight limit values, the remainder of the limit values remain unchanged.

The first optional [:SELected] node allows you to select which traffic channel band the setting is implemented in. The default band is the currently selected band, otherwise you can specify PGSM, EGSM, DCS, PCS, RGSM, GSM450, GSM480, GSM850, or GSM750.

Range: 1 to 8 comma-separated values ranging from -200 dBm to +100 dBm

Resolution: 0.1

Query

Range:8 comma-separated values ranging from -200 dBm to +100 dBm

Resolution: 0.1

Offset 1: -23 dBm
Offset 2: -26 dBm
Offset 3: -23 dBm
Offset 4: -26 dBm
Offset 5: -32 dBm
Offset 6: -32 dBm
Offset 7: -36 dBm
Offset 8: -36 dBm

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:LIMIT:MANUAL:GPRS -30DBM,-32DBM" 
!Sets the first two offsets in the GPRS format to -30 dBm and -32 dBm respectively.

Function

GSM

This command allows you to set the limits for the ORFS due to switching measurement in the in the GPRS format whether or not that format is active. You can enter up to eight limit values, one for each of the ORFS due to switching offset frequencies. The n ^th limit value is the value for the n ^th offset frequency, regardless of whether the offset frequency is switched on or off. Changing the offset value has no effect on the limit value. If you supply fewer than eight limit values, the remainder of the limit values remain unchanged.

The first optional [:SELected] node allows you to select which traffic channel band the setting is implemented in. The default band is the currently selected band, otherwise you can specify PGSM, EGSM, DCS, PCS, RGSM, GSM450, GSM480, GSM850, or GSM750.

GPRS

Range: 1 to 8 comma-separated values ranging from -200 dBm to +100 dBm

Resolution: 0.1

Query

Range:8 comma-separated values ranging from -200 dBm to +100 dBm

Resolution: 0.1

Offset 1: -23 dBm
Offset 2: -26 dBm
Offset 3: -23 dBm
Offset 4: -26 dBm
Offset 5: -32 dBm
Offset 6: -32 dBm
Offset 7: -36 dBm
Offset 8: -36 dBm

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:SWITCHING:LIMIT:MANUAL:GSM -30DBM,-32DBM" 
!Sets the first two offsets in the GSM format to -30 dBm and -32 dBm respectively.

Function

GSM

GPRS

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

Query

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:TIMEOUT:TIME 15" 
!Sets the timeout value to 15 seconds.

Function

GSM

GPRS

This command selects/queries the timeout value in seconds that will be used for ORFS measurements when the SETup:ORFSpectrum:TIMeout:STATe[:SELected] is ON in the GPRS format whether or not that format is active. The units (S|MS) are optional. If no units are specified than units default to S.

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

Query

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

10 seconds

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:TIMEOUT:TIME:GPRS 15" 
!Sets the timeout value to 15 seconds.

Function

GSM

This command selects/queries the timeout value in seconds that will be used for ORFS measurements when the SETup:ORFSpectrum:TIMeout:STATe[:SELected] is ON in the GSM format whether or not that format is active. The units (S|MS) are optional. If no units are specified than units default to S.

GPRS

This command is not applicable to GPRS.

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

Query

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

10 seconds

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:TIMEOUT:TIME:GSM 15" 
!Sets the timeout value to 15 seconds.

Function

GSM

This command sets/queries the timeout value in seconds that will be used for ORFS measurements and turns the timeout state on in the active (that is the selected) format. The units (S|MS) are optional. If no units are specified than units default to S.

GPRS

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

Query

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:TIMEOUT:STIME 12" 
!Sets the timeout value to 12 seconds and the state to on.

Function

GSM

This command is not applicable to GSM.

GPRS

This command sets/queries the timeout value in seconds that will be used for ORFS measurements and turns the timeout state on in the GPRS format whether or not that format is active. The units (S|MS) are optional. If no units are specified than units default to S.

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

Query

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

10 seconds

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:TIMEOUT:STIME:GPRS 12" 
!Sets the timeout value to 12 seconds and the state to on.

Function

GSM

This command sets/queries the timeout value in seconds that will be used for ORFS measurements and turns the timeout state on in the GSM format whether or not that format is active. The units (S|MS) are optional. If no units are specified than units default to S.

GPRS

This command is not applicable to GPRS.

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

Query

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

10 seconds

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:TIMEOUT:STIME:GSM 12" 
!Sets the timeout value to 12 seconds and the state to on.

Function

GSM

This command selects/queries the ORFS measurement timeout state in the active (that is the selected) format.

GPRS

Range: 0|OFF | 1|ON

Query

Range: 0|1

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:TIMEOUT:STATE ON" !Sets timeout state to on.

Function

GSM

This command is not applicable to GSM

GPRS

This command selects/queries the ORFS measurement timeout state in the GPRS format whether or not the format is active.

Range: 0|OFF | 1|ON

Query

Range: 0|1

0 (off)

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:TIMEOUT:STATE:GPRS ON" !Sets timeout state to on.

Function

GSM

This command selects/queries the ORFS measurement timeout state in the GSM format whether or not that format is active.

GPRS

This command is not applicable to GPRS

Range: 0|OFF | 1|ON

Query

Range: 0|1

0 (off)

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:TIMEOUT:STATE:GSM ON" !Sets timeout state to on.

Function

GSM

This command sets/queries the trigger delay for ORFS measurements in the active (that is the selected) format. The units (S|MS|US|NS) are optional, if no units are specified than units default to S.

GPRS

Range: -2.31 ms to +2.31 ms

Resolution: 5 significant digits or 100 nanoseconds whichever is greater

Query

Range: -2.31 ms to +2.31 ms

Resolution: 5 significant digits or 100 nanoseconds whichever is greater

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:TRIGGER:DELAY 1MS" 
!Sets the trigger delay value to 1 millisecond.

Function

GSM

This command is not applicable to GSM.

GPRS

This command sets/queries the trigger delay for ORFS measurements in the GPRS format whether or not that format is active. The units (S|MS|US|NS) are optional, if no units are specified than units default to S.

Range: -2.31 ms to +2.31 ms

Resolution: 5 significant digits or 100 nanoseconds whichever is greater

Query

Range: -2.31 ms to +2.31 ms

Resolution: 5 significant digits or 100 nanoseconds whichever is greater

0 seconds

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:TRIGGER:DELAY:GPRS 1MS" 
!Sets the trigger delay value to 1 millisecond.

Function

GSM

This command sets/queries the trigger delay for ORFS measurements in the GSM format whether or not that format is active. The units (S|MS|US|NS) are optional, if no units are specified than units default to S.

GPRS

This command is not applicable to GPRS.

Range: -2.31 ms to +2.31 ms

Resolution: 5 significant digits or 100 nanoseconds whichever is greater

Query

Range: -2.31 ms to +2.31 ms

Resolution: 5 significant digits or 100 nanoseconds whichever is greater

0 seconds

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:TRIGGER:DELAY:GSM 1MS" 
!Sets the trigger delay value to 1 millisecond.

Function

GSM

GPRS

Range: AUTO | IMMediate | PROTocol | RISE

See Triggering of Measurements .

Query

Range: AUTO | IMM | PROT | RISE

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:TRIGGER:SOURCE AUTO" 
!Sets the trigger source to automatic.

Function

GSM

GPRS

This command selects/queries the trigger source for ORFS measurements in the GPRS format whether or not that format is active. See Output RF Spectrum Measurement Description .

Range: AUTO | IMMediate | PROTocol | RISE

See Triggering of Measurements .

Query

Range: AUTO | IMM | PROT | RISE

AUTO

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:TRIGGER:SOURCE:GPRS AUTO" 
!Sets the trigger source to automatic.

Function

GSM

This command selects/queries the trigger source for ORFS measurements in the GSM format whether or not that format is active. See Output RF Spectrum Measurement Description .

GPRS

This command is not applicable to GPRS.

Range: AUTO | IMMediate | PROTocol | RISE

See Triggering of Measurements .

Query

Range: AUTO | IMM | PROT | RISE

AUTO

Programming Example

 
OUTPUT 714;"SETUP:ORFSPECTRUM:TRIGGER:SOURCE:GSM AUTO" 
!Sets the trigger source to automatic.