Last updated: December 2, 2008
The features and functionality present in the E6701T Special GSM/GPRS/EGPRS Lab Application are identical to those offered in the E6701E GSM/GPRS/EGPRS Lab Application, with the exceptions described in this document. For information on how to use the features that are common to the E6701E and E6701T, see the GSM/GPRS/EGPRS online user's guide located at:
http://wireless.keysight.com/rfcomms/refdocs/gsmgprs/default.php
The E6701T can only be loaded onto an E5515C with Special High Data Rate Hardware (or a test set with the equivalent hardware upgrades). Contact your local Keysight Sales Representative for more information, or visit www.keysight.com/find/8960upgrades.
In a test set with Special High Data Rate Hardware, the standard Protocol Processor is replaced with a High Data Rate Protocol Processor, and the test set's rear panel is modified to include a new LAN 2 PORT , which you must use for sending data to the test set (previously the LAN 1 PORT was used for this purpose).
The Special High Data Rate Hardware required to run the E6701T includes a modified rear panel with a new
LAN 2 PORT
. To use the E6701T
Data Channels
functionality (to establish an Packet-Switched Data connection, for example), you must connect your data server to
LAN 2 PORT
, rather than to
LAN 1 PORT
as in the past.
LAN 1 PORT
is still used for all other LAN operations such as protocol logging, firmware downloads and screen captures.
The LAN 2 PORT connects directly to the test set's High Data Rate protocol processor, as shown in the block diagram below.
You must configure the address of the
LAN 2 PORT
using the
LAN IP Address 2 (Data+)
setting (see
Configuring the Test Set's LAN
for general information about LAN IP addresses). LAN IP Address 2 (Data+) must not be the identical to the
LAN IP Address
setting, and must be on the same subnet as the
LAN IP Address
setting. If
LAN IP Address
or
Subnet Mask
is changed such that
LAN IP Address 2 (Data+)
is identical to or is no longer on the same subnet as
LAN IP Address
, then
LAN IP Address 2 (Data+)
is set to
0.0.0.0
and a warning is posted.
LAN IP Address 2 (Data+)
is accessible from the
Instrument Setup
menu on the
System Config Screen
. The GPIB command for
LAN IP Address 2 (Data+)
is
SYSTem:COMMunicate:LAN[:SELF]:ADDRess2<sp><string>
. See
SYSTem:COMMunicate:GPIB:[:SELF]:ADDRess
for range information.
External Device Connection
using one or more test sets running the E6703U, you must connect both the
LAN 1 PORT
and
LAN 2 PORT
to the LAN switch.
External Device Connection
from a test set running the E6703U, the destination test set displays the E6703U's
LAN IP Address 2 (Data+)
under
Connected Device IP Address
.
Ext 8960 IP Addr
to the
LAN IP Address 2 (Data+)
of the E6703U test set (unless you've connected the two test sets via a hub and have connections to the E6703U test set's
LAN 1 PORT
and
LAN 2 PORT
; in that case you can set
Ext 8960 IP Addr
to the E6703U test set's
LAN IP Address
or
LAN IP Address 2 (Data+)
.)
SYSTem:APPLication:CATalog[:NAME]?
query includes
"1xEV-DO Lab App T"
,
"CDMA 2000 Lab App T"
,
"GSM/GPRS Lab App T"
, "GSM/GPRS_WCDMA Lab App T" and
"WCDMA Lab App T"
.
SYSTem:APPLication:CATalog:LICense:APPLIcation:ALL?
query includes
"E6701T","GSM/GPRS LA rev T"
,
"E6702T","CDMA2000 LA rev T"
,
"E6703T","WCDMA LA rev T"
,
"E6706T","1xEV-DO LA rev T"
,
"E6706T-102","1xEV-DO Re A ETAP"
and
"E6785T","GSM/GPRS_WCDMA LA rev T"
.
SYSTem:APPLication[:CURRent][:NAME]?
query returns
"GSM/GPRS Lab App T"
.