How to use the Digital Audio Interface Features
Last updated: September 29, 2009
This section is only applicable to lab applications and the test application with a required feature license.
This section describes general procedures for performing the Digital Audio Interface (DAI) Test from the test set's front panel.
How to record the Digital Audio Interface (DAI) File
-
Connect the mobile station to the test set using a suitable RF connector and adaptor and connect the mobile station to the Customer test station using a suitable LAN cable.
-
Power on the mobile station, the test set and the mobile station.
-
Configure the DAI test mode.
-
Press
Call Setup
.
-
Press
TCH Parameters
(
F8
).
-
Press the
More
key until screen
2 of 3
of the
TCH Parameters
menu is displayed.
-
Press
Internal Test Loops
(
F9
).
-
Press
DAI Setup
(
F8
) and the
DAI Setup
menu appears in the center of the screen as shown in the figure below. Use the knob to select Speech Decoder. This results in the test set sending a Layer 3 message to the Mobile Station to inform it to accept the digital audio files from the test set.
-
Select the Logical Speech Channel that is to be tested.
-
Press
Call Setup
.
-
Press
TCH Parameters
(
F8
).
-
Press
Channel Mode Setup
(
F11
).
-
Press
Channel Mode Config
(
F7
) and the
Channel Mode Configuration
is displayed. Use the knob to highlight the
Logical Speech Channel
and select the desired Logical Speech Channel from the list.
-
Start a voice call between the test set and the DUT.
You can establish a Mobile Terminated Call by:
-
Press
Call Setup
-
Press
Originate Call
(
F3
)
-
Press the button on the mobile station that answers the call.
Or you can establish a Mobile Originated Call by dialing a number on the mobile station and pressing the button on the mobile station that sends a call.
-
Command the test set to start recording the digital audio file (COD/DEC reference file).
-
Press
Call Setup
-
Press the
More
key until screen
3 of 3
of the
Control
menu is displayed.
-
Press
Digital Audio Interface
(
F1
), The following screen is displayed.
-
Press
AMR Recording Format
(
F3
), set the Recording Format.
-
Press
Start COD Record
(
F2
), notice that the softkey changes to
Stop COD Record
after the press.
Note that 2MB limit is reached as the buffer indicator reaches 100%.
-
Press
Stop COD Record
(
F2
) when the COD record finished.
-
Download the digital audio file using the DAI File Manager.
How to play the Digital Audio Interface (DAI) File
-
Connect the mobile station to the test set using a suitable RF connector and adaptor and connect the mobile station to the Customer test station using a suitable LAN cable.
-
Power on the mobile station, the test set and the mobile station.
-
Select the Logical Speech Channel that is to be tested.
-
Press
Call Setup
.
-
Press
TCH Parameters
(
F8
).
-
Press
Channel Mode Setup
(
F11
).
-
Press
Channel Mode Config
(
F7
) and the
Channel Mode Configuration
is displayed. Use the knob to highlight the
Logical Speech Channel
and select the desired Logical Speech Channel from the list.
-
Upload the digital audio file using the DAI File Manager.
-
Start a voice call between the test set and the DUT.
You can establish a Mobile Terminated Call by:
-
Press
Call Setup
-
Press
Originate Call
(
F3
)
-
Press the button on the mobile station that answers the call.
Or you can establish a Mobile Originated Call by dialing a number on the mobile station and pressing the button on the mobile station that sends a call.
-
Command the test set to start playing the digital audio file (COD/DEC reference file).
-
Press
Call Setup.
-
Press the
More
key until screen
3 of 3
of the
Control
menu is displayed.
-
Press
Digital Audio Interface
(
F1
), The following screen is displayed.
-
Press
Start COD Play
(
F1
).