FETCh:PFERror

FETCh:PFERror

Last updated: March 18, 2009

GPIB Command Conventions

FETCh:PFERor[:ALL]?

Function	GSM TA	Queries integrity indicator, maximum RMS phase error, maximum peak phase error and worst frequency error.
	GPRS TA
	EGPRS TA
	GSM/GPRS LA
	EGPRS LA
Query		Integrity indicator Range: See Integrity Indicator . Resolution: 1 Maximum RMS Phase Error Range: 0 degrees to 180 degrees and 9.91 E+37 (NAN) Resolution: 0.01 degrees Maximum Peak Phase Error Range: 0 degrees to 180 degrees and 9.91 E+37 (NAN) Resolution: 0.01 degrees Worst Frequency Error Range: -750 kHz to +750 kHz and 9.91 E+37 (NAN) Resolution: 0.1 kHz
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"FETCH:PFERROR:ALL?" ! Returns integrity, maximum RMS phase error, maximum peak phase error and ! worst frequency error.

FETCh:PFERor:FAIL?

Function	GSM TA	Queries integrity indicator, RMS phase error pass/fail indicator, peak phase error pass/fail indicator, frequency error pass/fail indicator and the number of measurements taken. The number of measurements taken may be of interest to you if you are using the confidence level feature. For more information on using confidence levels refer to Confidence Levels .
	GPRS TA
	EGPRS TA
	GSM/GPRS LA
	EGPRS LA
Query		Integrity indicator Range: See Integrity Indicator . Resolution: 1 RMS Phase Error pass/fail indicator Range: 0\|1 Peak Phase Error pass/fail indicator Range: 0\|1 Frequency Error pass/fail indicator Range: 0\|1 Number of measurements taken Range: 0 to 999 and 9.91 E+37 (NAN) Resolution: 1
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"FETCH:PFERROR:FAIL?" ! Returns integrity, RMS phase error pass/fail result, peak phase error pass/fail ! result, frequency error pass/fail result and the number of measurements made.

FETCh:PFERror:COUNt:TESTed?

Function	GSM TA	Queries the number of measurements taken. If you are not using the confidence level feature then the value returned, after a successful measurement completes, is the same as that returned by the query of SETup:PFERror:COUNt:NUMBer . However if you are using the confidence level feature then this value may be lower than that set for multi-measurements.
	GPRS TA
	EGPRS TA
	GSM/GPRS LA
	EGPRS LA
Query		Range: 0 to 999 and 9.91 E+37 (NAN) Resolution: 1
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
Requirements	GSM/GPRS/ EGPRS LA	Revision: C.01 and above

FETCh:PFERror:FERRor:ALL?

Function	GSM TA	Queries minimum, maximum, average, and worst frequency error, in Hz. The minimum frequency error is the value closest to negative infinity from the last multi-measurement cycle. The maximum frequency error is the value closest to positive infinity from the last multi-measurement cycle.
	GPRS TA
	EGPRS TA
	GSM/GPRS LA
	EGPRS LA
Query		Minimum Frequency Error Range: -750 kHz to +750 kHz and 9.91 E+37 (NAN) Resolution: 0.1 kHz Maximum Frequency Error Range: -750 kHz to +750 kHz and 9.91 E+37 (NAN) Resolution: 0.1 kHz Average Frequency Error Range: -750 kHz to +750 kHz and 9.91 E+37 (NAN) Resolution: 0.1 kHz Worst Frequency Error Range: -750 kHz to +750 kHz and 9.91 E+37 (NAN) Resolution: 0.1 kHz
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"FETCH:PFERROR:FERROR:ALL?" ! Returns minimum, maximum, average and worst frequency error results.

FETCh:PFERror:FERRor:AVERage?

Function	GSM TA	Queries the single or average (from a multi-measurement) frequency error measurement result, in Hz.
	GPRS TA
	EGPRS TA
	GSM/GPRS LA
	EGPRS LA
Query		Range: -750 kHz to +750 kHz and 9.91 E+37 (NAN) Resolution: 0.1 kHz
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
Requirements	GSM/GPRS/ EGPRS LA	Revision: C.01 and above

FETCh:PFERror:FERRor:FAIL?

Function	GSM TA	Queries whether the frequency error passed or failed the value set using either of the following commands: SETup:PFERror:FERRor[:LIMit]:GSM , or SETup:PFERror:FERRor[:LIMit][:SELected]
	GSM/GPRS LA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS LA	This command is not applicable to EGPRS.
Query		Range: 0 (pass), 1 (fail), and 9.91 E+37 (NAN)
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
Requirements	GSM/GPRS/ EGPRS LA	Revision: C.01 and above

FETCh:PFERror:FERRor: MAXimum?

Function	GSM TA	Queries the maximum (from a multi-measurement) frequency error measurement result, in Hz.
	GPRS TA
	EGPRS TA
	GSM/GPRS LA
	EGPRS LA
Query		Range: -750 kHz to +750 kHz and 9.91 E+37 (NAN) Resolution: 0.1 kHz
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
Requirements	GSM/GPRS/ EGPRS LA	Revision: C.01 and above

FETCh:PFERror:FERRor:MINimum?

Function	GSM TA	Queries the minimum (from a multi-measurement) frequency error measurement result, in Hz.
	GPRS TA
	EGPRS TA
	GSM/GPRS LA
	EGPRS LA
Query		Range: -750 kHz to +750 kHz and 9.91 E+37 (NAN) Resolution: 0.1 kHz
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
Requirements	GSM/GPRS/ EGPRS LA	Revision: C.01 and above

FETCh:PFERror:FERRor[:WORSt]?

Function	GSM TA	Queries the frequency error from the individual multi-measurements that is furthest from 0 Hz. If the most positive and the most negative frequency errors are the same, the positive value will be returned.
	GPRS TA
	EGPRS TA
	GSM/GPRS LA
	EGPRS LA
Query		Range: -750 kHz to +750 kHz and 9.91 E+37 (NAN) Resolution: 0.1 kHz
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
Requirements	GSM/GPRS/ EGPRS LA	Revision: C.01 and above

FETCh:PFERror:ICOunt?

Function	GSM TA	Queries the intermediate count of phase and frequency multi-measurements completed. This number will increase to the value returned by SETup:PFERror:COUNt:NUMBer .
	GPRS TA
	EGPRS TA
	GSM/GPRS LA
	EGPRS LA
Query		Range: 0 to 999 Resolution: 1
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
Requirements	GSM/GPRS/ EGPRS LA	Revision: C.01 and above

FETCh:PFERror:INTegrity?

Function	GSM TA	Queries the integrity indicator for the phase and frequency error measurement. Zero indicates a normal result. See Integrity Indicator for descriptions of non-zero integrity indicators.
	GPRS TA
	EGPRS TA
	GSM/GPRS LA
	EGPRS LA
Query		Range: See Integrity Indicator . Resolution: 1
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
Requirements	GSM/GPRS/ EGPRS LA	Revision: C.01 and above

FETCh:PFERror:PEAK:ALL?

Function	GSM TA	Queries the minimum, maximum, and average peak phase error measurement result, in degrees.
	GPRS TA
	EGPRS TA
	GSM/GPRS LA
	EGPRS LA
Query		Minimum Peak Phase Error Range: 0 degrees to 180 degrees and 9.91 E+37 (NAN) Resolution: 0.01 degrees Maximum Peak Phase Error Range: 0 degrees to 180 degrees and 9.91 E+37 (NAN) Resolution: 0.01 degrees Average Peak Phase Error Range: 0 degrees to 180 degrees and 9.91 E+37 (NAN) Resolution: 0.01 degrees
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"FETCH:PFERROR:PEAK:ALL?" ! Returns minimum, maximum, and average peak phase error results.

FETCh:PFERror:PEAK:AVERage?

Function	GSM TA	Queries the single or average (from a multi-measurement) peak phase error measurement result, in degrees.
	GPRS TA
	EGPRS TA
	GSM/GPRS LA
	EGPRS LA
Query		Range: 0 degrees to 180 degrees and 9.91 E+37 (NAN) Resolution: 0.01 degrees
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
Requirements	GSM/GPRS/ EGPRS LA	Revision: C.01 and above

FETCh:PFERror:PEAK:FAIL?

Function	GSM TA	Queries whether the peak phase error passed or failed the value set using either of the following commands: SETup:PFERror:PEAK[:LIMit]:GSM , or SETup:PFERror:PEAK[:LIMit][:SELected]
	GSM/GPRS LA
	EGPRS TA
	GPRS TA	This command is not applicable to GPRS.
	EGPRS LA	This command is not applicable to EGPRS.
Query		Range: 0 (pass), 1 (fail), and 9.91 E+37 (NAN)
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
Requirements	GSM/GPRS/ EGPRS LA	Revision: C.01 and above

FETCh:PFERror:PEAK[:MAXimum]?

Function	GSM TA	Queries the maximum (from a multi-measurement) peak phase error result, in degrees.
	GPRS TA
	EGPRS TA
	GSM/GPRS LA
	EGPRS LA
Query		Range: 0 degrees to 180 degrees and 9.91 E+37 (NAN) Resolution: 0.01 degrees
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
Requirements	GSM/GPRS/ EGPRS LA	Revision: C.01 and above

FETCh:PFERror:PEAK:MINimum?

Function	GSM TA	Queries the minimum (from a multi-measurement) peak phase error measurement result, in degrees.
	GPRS TA
	EGPRS TA
	GSM/GPRS LA
	EGPRS LA
Query		Range: 0 degrees to 180 degrees and 9.91 E+37 (NAN) Resolution: 0.01 degrees
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
Requirements	GSM/GPRS/ EGPRS LA	Revision: C.01 and above

FETCh:PFERror:RMS:ALL?

Function	GSM TA	Queries the minimum, maximum, and average RMS phase error measurement result, in degrees.
	GPRS TA
	EGPRS TA
	GSM/GPRS LA
	EGPRS LA
Query		Minimum RMS Phase Error Range: 0 degrees to 180 degrees and 9.91 E+37 (NAN) Resolution: 0.01 degrees Maximum RMS Phase Error Range: 0 degrees to 180 degrees and 9.91 E+37 (NAN) Resolution: 0.01 degrees Average RMS Phase Error Range: 0 degrees to 180 degrees and 9.91 E+37 (NAN) Resolution: 0.01 degrees
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"FETCH:PFERROR:RMS:ALL?" ! Returns minimum, maximum, and average RMS phase error.

FETCh:PFERror:RMS:AVERage?

Function	GSM TA	Queries the single or average (from a multi-measurement) RMS phase error measurement result, in degrees.
	GPRS TA
	EGPRS TA
	GSM/GPRS LA
	EGPRS LA
Query		Range: 0 degrees to 180 degrees and 9.91 E+37 (NAN) Resolution: 0.01 degrees
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
Requirements	GSM/GPRS/ EGPRS LA	Revision: C.01 and above

FETCh:PFERror:RMS:FAIL?

Function	GSM TA	Queries whether the RMS phase error passed or failed the value set using either of the following commands: SETup:PFERror:RMS[:LIMit]:GSM , or SETup:PFERror:RMS[:LIMit][:SELected]
	GPRS TA
	EGPRS TA
	GSM/GPRS LA
	EGPRS LA
Query		Range: 0 (pass), 1 (fail), and 9.91 E+37 (NAN)
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
Requirements	GSM/GPRS/ EGPRS LA	Revision: C.01 and above

FETCh:PFERror:RMS[:MAXimum]?

Function	GSM TA	Queries the Maximum (from a multi-measurement) RMS phase error measurement result, in degrees.
	GPRS TA
	EGPRS TA
	GSM/GPRS LA
	EGPRS LA
Query		Range: 0 degrees to 180 degrees and 9.91 E+37 (NAN) Resolution: 0.01 degrees
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"FETCH:PFERROR:RMS:MAXIMUM?" ! Returns the maximum RMS phase error.

FETCh:PFERror:RMS:MINimum?

Function	GSM TA	Queries the minimum (from a multi-measurement) RMS phase error measurement result, in degrees.
	GPRS TA
	EGPRS TA
	GSM/GPRS LA
	EGPRS LA
Query		Range: 0 degrees to 180 degrees and 9.91 E+37 (NAN) Resolution: 0.01 degrees
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
Requirements	GSM/GPRS/ EGPRS LA	Revision: C.01 and above

FETCh:PFERror:SYMBol:DATA?

Function	GSM TA	Queries the Phase Frequency Error measurement and returns 148 points representing the demodulated symbols
	GPRS TA
	EGPRS TA
	GSM/GPRS LA
	EGPRS LA
Query		Range: 0 \|1\|-1 where -1 indicates a symbol that could not be demodulated
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"FETCH:PFERror:SYMBol:DATA?" ! Returns the 148 demondulated bits.