SETup:ETXPower

SETup:ETXPower

Last updated: May 31, 2010

GPIB Command Conventions

SETup:ETXPower:CONTinuous

Function	GSM TA	This command is not applicable to the GSM Test Application
	GPRS TA	This command is not applicable to the GPRS Test Application.
	GSM/GPRS LA	This command is not applicable to the GSM/GPRS Lab Application.
	EGPRS TA	This command sets/queries the trigger state for EGPRS TX carrier power measurements.
	EGPRS LA
Setting		Range: Single trigger mode = 0 \| OFF Continuous trigger mode = 1 \| ON
Query		Range: 0 \| 1
*RST Setting		0 \| OFF
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETup:ETXPower:CONTinuous ON" ! Specifies continuous trigger mode for EGPRS TX carrier power measurements.

SETup:ETXPower:COUNt[:SNUMber]

Function	GSM TA	This command is not applicable to the GSM.Test Application
	GPRS TA	This command is not applicable to the GPRS Test Application.
	GSM/GPRS LA	This command is not applicable to the GSM/GPRS Lab Application.
	EGPRS TA	This command sets/queries the number of EGPRS TX carrier power measurements made by the test set. This command sets the count state to ON.
	EGPRS LA
Setting		Range: 1 to 999 Resolution: 1
Query		Range: 1 to 999 Resolution: 1
*RST Setting		10
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETup:ETXPower:COUNt:SNUMber 99" ! Sets the state to on and the multi-measurement count value to 99.

SETup:ETXPower:COUNt:NUMBer

Function	GSM TA	This command is not applicable to the GSM.Test Application
	GPRS TA	This command is not applicable to the GPRS Test Application.
	GSM/GPRS LA	This command is not applicable to the GSM/GPRS Lab Application.
	EGPRS TA	This command sets/queries the number of EGPRS TX power measurements the test set makes in the active (that is the selected) format. The multi-measurement count state must be on.
	EGPRS LA
Setting		Range: 1 to 999 Resolution: 1
Query		Range: 1 to 999 Resolution: 1
*RST Setting		10
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETup:ETXPower:COUNt:NUMBer 5" ! Sets the EGPRS TX Power multi-measurementcount number to 5.

SETup:ETXPower:COUNt:STATe

Function	GSM TA	This command is not applicable to the GSM.Test Application
	GPRS TA	This command is not applicable to the GPRS Test Application.
	GSM/GPRS LA	This command is not applicable to the GSM/GPRS Lab Application.
	EGPRS TA	This command sets/queries the EGPRS TX power multi-measurement count state.
	EGPRS LA
Setting		Range: 0 \| OFF \| 1 \| ON
Query		Range: 0 \| 1
*RST Setting		0 \| OFF
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETup:ETXPower:COUNt:STATe ON" ! Sets the multi-measurement count state to on.

SETup:ETXPower:ECPower:STATe

Function	GSM TA	This command is not applicable to the GSM.Test Application
	GPRS TA	This command is not applicable to the GPRS Test Application.
	GSM/GPRS LA	This command is not applicable to the GSM/GPRS Lab Application.
	EGPRS TA	This command sets/queries the EGPRS TX power estimated carrier power state. When set to ON (1) and the modulation format is set to 8PSK, the estimated carrier power measurement is calculated and the result is available via GPIB and on the test set's front panel. When set to OFF (0) and the modulation format is set to 8PSK, the estimated carrier power measurement is not calculated. The power measurement completes in a shorter time when this command is set to OFF. If the modulation format is set to GMSK, only the transmit power value is displayed on the test set's front panel, and the transmit power is returned via GPIB when the estimated carrier power result is queried.
	EGPRS LA
Setting		Range: 0 \| OFF \| 1 \| ON
Query		Range: 0 \| 1
*RST Setting		0 \| OFF
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETup:ETXPower:COUNt:STATe ON" ! Sets the multi-measurement count state to on.

SETup:ETXPower:TIMeout[:STIMe]

Function	GSM TA	This command is not applicable to the GSM.Test Application
	GPRS TA	This command is not applicable to the GPRS Test Application.
	GSM/GPRS LA	This command is not applicable to the GSM/GPRS Lab Application.
	EGPRS TA	This command sets/queries the EGPRS TX carrier power measurement timeout value. This command also sets the count state to on. The units (S\|MS) are optional, if no units are specified then units default to S.
	EGPRS LA
Setting		Range: 0.1 to 999.9 seconds Resolution: 0.1 seconds
Query		Range: 0.1 to 999.9 seconds Resolution: 0.1 seconds
*RST Setting		10 seconds
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETup:ETXPower:TIMeout:STIMe 20" ! Sets the state to on and the timeout value to 20 seconds.

SETup:ETXPower:TIMeout:TIME

Function	GSM TA	This command is not applicable to the GSM.Test Application
	GPRS TA	This command is not applicable to the GPRS Test Application.
	GSM/GPRS LA	This command is not applicable to the GSM/GPRS Lab Application.
	EGPRS TA	This command sets/queries the timeout value in seconds that will be used for EGPRS TX power measurements in the active (that is the selected) format. The units (S\|MS) are optional, if no units are specified then units default to S.
	EGPRS LA
Setting		Range: 0.1 to 999.9 seconds Resolution: 0.1 seconds
Query		Range: 0.1 to 999.9 seconds Resolution: 0.1 seconds
*RST Setting		10 seconds
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETup:ETXPower:TIMeout:TIME 20" ! Sets the EGPRS TX power measurement timeout to 20 seconds.

SETup:ETXPower:TIMeout:STATe

Function	GSM TA	This command is not applicable to the GSM.Test Application
	GPRS TA	This command is not applicable to the GPRS Test Application.
	GSM/GPRS LA	This command is not applicable to the GSM/GPRS Lab Application.
	EGPRS TA	This command selects/queries EGPRS TX carrier power measurement timeout state in the active (that is the selected) format.
	EGPRS LA
Setting		Range: 0 \| OFF \| 1 \| ON
Query		Range: 0 \| 1
*RST Setting		0 \| OFF
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETup:ETXPower:COUNt:STATe 1" ! Turns the EGPRS TX carrier power timeout state on.

SETup:ETXPower:TRIGger:DELay

Function	GSM TA	This command is not applicable to the GSM.Test Application
	GPRS TA	This command is not applicable to the GPRS Test Application.
	GSM/GPRS LA	This command is not applicable to the GSM/GPRS Lab Application.
	EGPRS TA	This command sets/queries the trigger delay in seconds for EGPRS TX carrier power measurements in the active (that is the selected) format. The units (S\|MS\|US\|NS) are optional, if no units are specified then units default to S.
	EGPRS LA
Setting		Range: -2.31 ms to +2.31 ms Resolution: 5 significant digits or 100 ns, whichever is greater
Query		Range: -2.31 ms to +2.31 ms Resolution: 5 significant digits or 100 ns, whichever is greater
*RST Setting		0 seconds
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETup:ETXPower:TRIGger:DELay 1.5MS" ! Set trigger delay time to 1.5 milliseconds

SETup:ETXPower:TRIGger:SOURce

Function	GSM TA	This command is not applicable to the GSM.Test Applicaton
	GPRS TA	This command is not applicable to the GPRS Test Application.
	GSM/GPRS LA	This command is not applicable to the GSM/GPRS Lab Application.
	EGPRS TA	This command selects/queries the trigger source for EGPRS TX carrier power measurements in the active (that is the selected) format. See Triggering of Measurements .
	EGPRS LA
Setting		AUTO \| PROTocol \| RISE \| IMMediate
Query		AUTO \| PROT \| RISE \| IMM
*RST Setting		AUTO
Requirements	GSM/GPRS/ EGPRS TA	Revision: A.01 and above
	GSM/GPRS/ EGPRS LA	Revision: C.01 and above
Programming Example OUTPUT 714;"SETup:ETXPower:TRIGger:SOURce AUTO" ! Sets trigger source to automatic.