CALL:UPLink

Function

Sets/queries the Maximum Allowed UL TX Power setting.

The setting can be set in active cell operating mode only when the call status is Idle, or in other operating modes.

If BCCH Update Page is set to Auto and you change the setting while your UE is camped to the test set, the test set performs a Broadcast Channel (BCCH) Update Procedure ; If BCCH Update Page is set to Inhibit (the default value) and you change the setting while your UE is camped to the test set, the UE is informed to re-read the BCCH to observe the change (see CALL:BCCHannel:UPDAte:PAGE AUTO).

Setting

Range: -50 to +33 dBm

Query

Range: -50 to +33

*RST Setting

33

Requirements

Test Application Revision: A.02.00 and above

Programming Example

"CALL:UPLink:TXPower:LEVel:MAXimum 33"

Function

Sets/queries the UpPCH Power Ramp Step setting.

Setting

Range: 0|1|2|3 dB

Query

Range: 0|1|2|3

*RST Setting

3

Requirements

Test Application Revision: A.02.00 and above

Programming Example

"CALL:UPLink:UPPChannel:POWer:STEP 3"

Function

Sets/queries Desired UpPCH RX Power.

The setting can be set in active cell operating mode only when the call status is Idle, or in other operating modes.

Setting

Range: -120 to -58 dBm

Query

Range: -120 to -58

*RST Setting

-100

Requirements

Test Application Revision: A.02.00 and above

Programming Example

"CALL:UPLink:UPPChannel:POWer:LEVel -100"

Function

Queries the Initial UpPCH TX Power.

Query

Range: -65 to +30

Requirements

Test Application Revision: A.02.00 and above

Programming Example

"CALL:UPLink:UPPChannel:POWer:INITial?"

Function

Sets/queries SYNC UL Code Bitmap setting.

Setting

Range: 0000 0001 to 1111 1111

Query

Range: 0000 0001 to 1111 1111

*RST Setting

1111 1111

Requirements

Test Application Revision: A.02.00 and above

Programming Example

"CALL:UPLink:UPPChannel:SYNChronize:CBITmap '00000001'"

Function

Sets/queries the maximum numbers of SYNC_UL transmissions in a synchronisation attempt initiated by the UE. This parameter will be sent in SIB5 on BCCH.

Setting

Range: TRANsmit1 | TRANsmit2 | TRANsmit4 | TRANsmit8

Query

Range: TRAN1|TRAN2|TRAN4|TRAN8

*RST Setting

TRANsmit8

Requirements

Test Application Revision: A.02.00 and above

Programming Example

"CALL:UPLink:UPPChannel:SYNChronize:TRANsmission:MAXimum TRANsmit8"

Function

Sets/queries the maximum number of synchronisation attempts in one random access procedure. This parameter will be sent in SIB5 on BCCH.

Setting

Range: 1 to 32

Query

Range: 1 to 32

*RST Setting

32

Requirements

Test Application Revision: A.02.00 and above

Programming Example

"CALL:UPLink:UPPChannel:SYNChronize:ANUMber:MAXimum 32"

Function

Sets/queries Desired PRACH RX Power.

The setting can be set in active cell operating mode only when the call status is Idle, or in other operating modes.

Setting

Range: -120 to -80 dBm

Query

Range: -120 to -80

*RST Setting

-100

Requirements

Test Application Revision: A.02.00 and above

Programming Example

"CALL:UPLink:PRAChannel:POWer:LEVel -100"

Function

Queries the Initial PRACH TX Power.

Query

Range: -65 to +30

Requirements

Test Application Revision: A.02.00 and above

Programming Example

"CALL:UPLink:PRAChannel:POWer:INITial:LEVel?"