SETup:TXPower

Function

GSM

This command sets/queries the trigger state for TX carrier power measurements in the active (that is the selected) format.

GPRS

Range:

• Single trigger mode = 0|OFF
• Continuous trigger mode = 1|ON

Query

Range: 0|1

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:CONTINUOUS OFF" !Specifies single trigger mode for TX carrier power measurements.

Function

GSM

This command is not applicable to GSM.

GPRS

This command sets/queries the trigger state for TX carrier power measurements in the GPRS format whether or not that format is active.

Range:

• Single trigger mode = 0|OFF
• Continuous trigger mode = 1|ON

Query

Range: 0|1

0 (off)

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:CONTINUOUS:GPRS OFF" !Specifies single trigger mode for GPRS TX carrier power measurements.

Function

GSM

This command sets/queries the trigger state for TX carrier power measurements in the GSM format whether or not that format is active.

GPRS

This command is not applicable to GPRS.

Range:

• Single trigger mode = 0|OFF
• Continuous trigger mode = 1|ON

Query

Range: 0|1

0 (off)

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:CONTINUOUS:GSM OFF" !Specifies single trigger mode for GSM TX carrier power measurements.

Function

GSM

This command sets/queries the number of TX carrier power measurements the test set makes in the active (that is the selected) format. This command sets the count state to on.

GPRS

Range: 1 to 999

Resolution: 1

Query

Range: 1 to 999

Resolution: 1

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:COUNT:SNUMBER 99" 
!Sets the state to on and the multi-measurement count value to 99.

Function

GSM

This command is not applicable to GSM.

GPRS

This command sets/queries the number of TX carrier power measurements the test set makes in the GPRS format whether or not that format is active. This command sets the count state to on.

Range: 1 to 999

Resolution: 1

Query

Range: 1 to 999

Resolution: 1

10

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:COUNT:SNUMBER:GPRS 99" 
!Sets the state to on and the multi-measurement count value to 99.

Function

GSM

This command sets/queries the number of TX carrier power measurements the test set makes in the GSM format whether or not that format is active. This command sets the count state to on.

GPRS

This command is not applicable to GPRS.

Range: 1 to 999

Resolution: 1

Query

Range: 1 to 999

Resolution: 1

10

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:COUNT:SNUMBER:GSM 99" 
!Sets the state to on and the multi-measurement count value to 99.

Function

GSM

This command sets/queries the number of TX power measurements the test set makes in the active (that is the selected) format. The multi-measurement count state must be on.

GPRS

Range: 1 to 999

Resolution: 1

Query

Range: 1 to 999

Resolution: 1

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:COUNT:NUMBER 5" 
!Sets the TX Power multi-measurementcount number to 5.

Function

GSM

This command is not applicable to GSM.

GPRS

This command sets/queries the number of TX power measurements the test set makes in the GPRS format whether or not that format is active. The multi-measurement count state must be on.

Range: 1 to 999

Resolution: 1

Query

Range: 1 to 999

Resolution: 1

10

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:COUNT:NUMBER:GPRS 5" 
!Sets the TX Power multi-measurementcount number to 5.

Function

GSM

This command sets/queries the number of TX power measurements the test set makes in the GSM format whether or not that format is active. The multi-measurement count state must be on.

GPRS

This command is not applicable to GPRS.

Range: 1 to 999

Resolution: 1

Query

Range: 1 to 999

Resolution: 1

10

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:COUNT:NUMBER:GSM 5" 
!Sets the TX Power multi-measurementcount number to 5.

Function

GSM

This command sets/queries the TX power multi-measurement count state in the active (that is the selected) format.

GPRS

Range: 0|OFF | 1|ON

Query

Range: 0|1

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:COUNT:STATE ON" !Sets the multi-measurement count state to on.

Function

GSM

This command is not applicable to GSM.

GPRS

This command sets/queries the TX power multi-measurement count state in the GPRS format whether or not that format is active.

Range: 0|OFF | 1|ON

Query

Range: 0|1

0 (off)

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:COUNT:STATE:GPRS ON" !Sets the multi-measurement count state to on.

Function

GSM

This command sets/queries the TX power multi-measurement count state in the GSM format whether or not that format is active.

GPRS

This command is not applicable to GPRS.

Range: 0|OFF | 1|ON

Query

Range: 0|1

0 (off)

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:COUNT:STATE:GSM ON" !Sets the multi-measurement count state to on.

Function

GSM

This command sets/queries the TX carrier power measurement timeout value in the active (that is the selected) format. This command also sets the count state to on. The units (S|MS) are optional, if no units are specified then units default to S.

GPRS

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

Query

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:TIMEOUT:STIME 20" 
!Sets the state to on and the timeout value to 20 seconds.

Function

GSM

This command is not applicable to GSM.

GPRS

This command sets/queries the TX carrier power measurement timeout value in the GPRS format whether or not that format is active. This command also sets the count state to on. The units (S|MS) are optional, if no units are specified then units default to S.

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

Query

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

10 seconds

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:TIMEOUT:STIME:GPRS 20" 
!Sets the state to on and the timeout value to 20 seconds.

Function

GSM

This command sets/queries the TX carrier power measurement timeout value in the GSM format whether or not that format is active. This command also sets the count state to on. The units (S|MS) are optional, if no units are specified then units default to S.

GPRS

This command is not applicable to GPRS.

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

Query

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

10 seconds

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:TIMEOUT:STIME:GSM 20" 
!Sets the state to on and the timeout value to 20 seconds.

Function

GSM

This command sets/queries the timeout value in seconds that will be used for TX power measurements in the active (that is the selected) format. The units (S|MS) are optional, if no units are specified then units default to S.

GPRS

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

Query

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:TIMEOUT:TIME 20" 
!Sets the TX power measurement timeout to 20 seconds.

Function

GSM

This command is not applicable to GSM.

GPRS

This command sets/queries the timeout value in seconds that will be used for TX power measurements in the GPRS format whether or not that format is active. The units (S|MS) are optional, if no units are specified then units default to S.

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

Query

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

10 seconds

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:TIMEOUT:TIME:GPRS 20" 
!Sets the GPRS TX power measurement timeout to 20 seconds.

Function

GSM

This command sets/queries the timeout value in seconds that will be used for TX power measurements in the GSM format whether or not that format is active. The units (S|MS) are optional, if no units are specified then units default to S.

GPRS

This command is not applicable to GPRS.

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

Query

Range: 0.1 to 999 seconds

Resolution: 0.1 seconds

10 seconds

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:TIMEOUT:TIME:GSM 20" 
!Sets the GSM TX power measurement timeout to 20 seconds.

Function

GSM

This command selects/queries TX carrier power measurement timeout state in the active (that is the selected) format.

GPRS

Range: 0|OFF | 1|ON

Query

Range: 0|1

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:COUNT:STATE 1" 
!Turns the TX carrier power timeout state on.

Function

GSM

This command is not applicable to GSM.

GPRS

This command selects/queries TX carrier power measurement timeout state in the GPRS format whether or not that format is active.

Range: 0|OFF | 1|ON

Query

Range: 0|1

0 (off)

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:COUNT:STATE:GPRS 1" 
!Turns the GPRS TX carrier power timeout state on.

Function

GSM

This command selects/queries TX carrier power measurement timeout state in the GSM format whether or not that format is active.

GPRS

This command is not applicable to GPRS.

Range: 0|OFF | 1|ON

Query

Range: 0|1

0 (off)

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:COUNT:STATE:GSM 1" 
!Turns the GSM TX carrier power timeout state on.

Function

GSM

This command sets/queries the trigger delay in seconds for TX carrier power measurements in the active (that is the selected) format. The units (S|MS|US|NS) are optional, if no units are specified then units default to S.

GPRS

Range: -2.31 ms to +2.31 ms

Resolution: 5 significant digits or 100 ns, whichever is greater

Query

Range: -2.31 ms to +2.31 ms

Resolution: 5 significant digits or 100 ns, whichever is greater

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:TRIGGER:DELAY 1.5MS" !Set trigger delay time to 1.5 milliseconds

Function

GSM

This command is not applicable to GSM.

GPRS

This command sets/queries the trigger delay in seconds for TX carrier power measurements in the GPRS format whether or not that format is active. The units (S|MS|US|NS) are optional, if no units are specified then units default to S.

Range: -2.31 ms to +2.31 ms

Resolution: 5 significant digits or 100 ns, whichever is greater

Query

Range: -2.31 ms to +2.31 ms

Resolution: 5 significant digits or 100 ns, whichever is greater

zero seconds

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:TRIGGER:DELAY:GPRS 1.5MS" !Set trigger delay time to 1.5 milliseconds

Function

GSM

This command sets/queries the trigger delay in seconds for TX carrier power measurements in the GSM format whether or not that format is active. The units (S|MS|US|NS) are optional, if no units are specified then units default to S.

GPRS

This command is not applicable to GPRS.

Range: -2.31 ms to +2.31 ms

Resolution: 5 significant digits or 100 ns, whichever is greater

Query

Range: -2.31 ms to +2.31 ms

Resolution: 5 significant digits or 100 ns, whichever is greater

zero seconds

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:TRIGGER:DELAY:GSM 1.5MS" !Set trigger delay time to 1.5 milliseconds

Function

GSM

This command selects/queries the trigger source for TX carrier power measurements in the active (that is the selected) format. See Triggering of Measurements .

GPRS

AUTO|PROTocol|RISE|IMMediate

Query

AUTO|PROT|RISE|IMM

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:TRIGGER:SOURCE AUTO" !Sets trigger source to automatic.

Function

GSM

This command is not applicable to GSM.

GPRS

This command selects/queries the trigger source for TX carrier power measurements in the GPRS format whether or not that format is active. See Triggering of Measurements .

AUTO|PROTocol|RISE|IMMediate

Query

AUTO|PROT|RISE|IMM

AUTO

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:TRIGGER:SOURCE:GPRS AUTO" !Sets trigger source to automatic.

Function

GSM

This command selects/queries the trigger source for TX carrier power measurements in the GSM format whether or not that format is active. See Triggering of Measurements .

GPRS

This command is not applicable to GPRS.

AUTO|PROTocol|RISE|IMMediate

Query

AUTO|PROT|RISE|IMM

AUTO

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:TRIGGER:SOURCE:GSM AUTO" !Sets trigger source to automatic.

Function

GSM

This command sets/queries the trigger qualification for TX carrier power measurements in the active (that is the selected) format. When ON, an automatic trigger re-arm occurs if a measurement is triggered when no valid signal (burst) is present. See Trigger Qualifier Description .

GPRS

Range: 0|OFF | 1|ON

Query

Range: 0|1

The *RST value of this command depends on the format that is currently active. For example, if the GSM format is currently active, the *RST value for this command is the same value as the equivalent command containing the :GSM format identifier.

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:TRIGGER:QUALIFIER ON" !Sets trigger qualifier state to on.

Function

GSM

This command is not applicable to GSM.

GPRS

This command sets/queries the trigger qualification for TX carrier power measurements in the GPRS format whether or not that format is active. When ON, an automatic trigger re-arm occurs if a measurement is triggered when no valid signal (burst) is present. See Trigger Qualifier Description .

Range: 0|OFF | 1|ON

Query

Range: 0|1

1 (on)

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:TRIGGER:QUALIFIER:GPRS ON" !Sets trigger qualifier state to on.

Function

GSM

This command sets/queries the trigger qualification for TX carrier power measurements in the GSM format whether or not that format is active. When ON, an automatic trigger re-arm occurs if a measurement is triggered when no valid signal (burst) is present. See Trigger Qualifier Description .

GPRS

This command is not applicable to GPRS.

Range: 0|OFF | 1|ON

Query

Range: 0|1

1 (on)

Programming Example

 
OUTPUT 714;"SETUP:TXPOWER:TRIGGER:QUALIFIER:GSM ON" !Sets trigger qualifier state to on.