Manual Operation
This page provides links to information on using the test set from the front panel including: Call Processing Operations (such as making a call, handovers), Call Processing Configuration (configuring the test set's base station emulator), Making Measurements (how to use the measurements in general, and also how to perform 3GPP TS 34.121 tests, see Performing Individual Measurements and 3GPP TS 51.010 Tests ), Data Channel , Test Set Configuration (such as amplitude offsets, GPIB and LAN ports), General Manual Operation (such as Help Mode, which provides context-sensitive GPIB command syntax assistance, and Save and Recall Registers, which provide a way to return to frequently used setups).
Call Processing Operations
- How Do I Set Up a Call?
- How Do I End a Call?
- How do I Make Rach Measurements?
- How Do I Change the Payload Pattern Sent to the Mobile Station?
- How Do I Set Up and Use the Frequency Hopping Feature?
- How Do I Perform a Handover?
- How Do I Perform an EGPRS Handover?
- How Do I Access the Medium Access Control (MAC) Parameters? (GPRS/EGPRS LA Only)
- How to view Measurement Reports (LA Only)
- How to use the Adaptive Multi-Rate (AMR) and Wideband AMR (AMR-WB) Features (LA Only)
- How to use Protocol Logging (LA Only)
- How to use the Short Message Service Features (LA Only)
- Enabling the HTTP Interface
- How to use Timing Advance Control. (LA Only)
- How do I test Incremental Redundancy? (EGPRS LA only)
- How do I test MCS Switching? (EGPRS LA only)
- How do I change the Downlink TBF Puncturing Scheme? (EGPRS LA only)
- How Do I Use the Data Throughput Monitor? (LA Only)
- How Do I Perform Calling Party Number Verification? (LA Only)
- How Do I Set Up and Test Cell Selection and Transitions? (LA Only)
- How Do I Set the TBF Parameters? (GPRS/EGPRS LA Only)
- How Do I Set Up and Use the Dual Transfer Mode Feature? (LA Only)
- How to access DUT PDP Setup (GPRS/EGPRS LA Only)
- How to use the Digital Audio Interface Features (LA Only)
- How Do I Use Real-Time Vocoder?
- How Do I Set Up and Use the Configurable Timers?
- How Do I use Mobile Calculated BER Test
Call Processing Configuration
- How Do I Change Call Parameters?
- How Do I Change Cell Operation Parameters?
- How Do I Change Cell Parameters?
- How Do I Change Cell Identification Parameters?
- How Do I Change Cell List Parameters?
- How Do I Change Paging Parameters?
- How Do I Set the Training Sequence Code (TSC)?
- How to Configure Access Burst Power Control
- How to Configure Access Burst Power Control for DCS
- How Do I Configure the Speech Source?
- How Do I Configure the Call Signaling Parameters? (LA Only)
- How to access Protocol Control
- How Do I Configure the Control Channel Parameters?
- How Do I Configure the PDTCH Parameters?
- How Do I Configure the Type of Bursts used to Carry the Packet Control Acknowledgments? (LA Only)
- How Do I Change the MS TX Level?
- How Do I Change the EGPRS Modulation Coding Scheme?
- How Do I Assign Different Modulation Coding Schemes / Puncturing Schemes to Each Downlink of a Multislot Burst?
- How Do I Gain Access to All the EGPRS Multislot Configurations?
- How do I change the EGPRS Demodulation Type to Normal? (EGPRS TA Only)
Making Measurements
-
Performing Individual Measurements and 3GPP TS 51.010 Tests
click here for instructions for performing
3GPP TS 51.010 tests. - How Do I Make GSM Measurements on a Mobile?
- How Do I Make GPRS Measurements on a Mobile?
- How Do I Make EGPRS Measurements on a Mobile?
- How Do I Change Measurement Setup in GSM?
- How Do I Change Measurement Setup in GPRS?
- How Do I Change Measurement Setup in EGPRS?
- How Do I Turn Off a GSM Measurement?
- How Do I Turn Off a GPRS Measurement?
- How Do I Turn Off a Measurement in EGPRS?