Data Connection Processing

Last updated: October 30, 2013

This page provides links to descriptions of the numerous settings and operations available in the test set for base station emulation and data connection processing including: Data Connection Processing Overview , Access Network Emulator Configuration , Data Connection Processing Operations , Access Terminal Information , Test Set Operating Modes and General Information .

If you have trouble finding the information you need below, use the "Search" functionality to search the contents of this guide. If you are new to using the test set, it may be helpful to review the Getting Started with Data Connection Processing section, which further describes where to find key data connection processing content.

Data Connection Processing Overview

TAP/ETAP/MCTAP Data Connection Processing States Lifecycle
TAP/ETAP/MCTAP Data Connection Call Flow
C.S0029 Test Application Specification Description (TAP/ETAP/MCTAP)
Summary of Data Connection Processing States Description
Data Channel ( Lab Application Only ) (DPA based data connection, Mobile IP, Data Throughout Monitor, Hybrid Mode, etc.)
Multi-carrier Multi-unit (MCMU) (applicable to the lab application and to a test application with the required feature license )

Access Network Emulator Configuration

Parameters Under Call Control Menus	Parameters Under Call Parms Menus
Operating Mode , System Type	Cell Power
Handoff Setup	Cell Band
AT Max Power Parameter: AT Max Power Multicarrier AT Max Power Backoff (only for subtype 3 physical layer)	Channel
Session App Pre Configure
Access Network Info: Configurable Attribute Parms: Preferred Control Channel Cycle Control , Release A Physical Layer Subtype , Release B Physical Layer Subtype , Access Channel MAC Subtype , Rate 1M8 Supported Control ( only for subtype 2 physical layer ), Idle State Subtype In Use , Enhanced Idle State Protocol Slotted Control (Lab Application Only ). Cell Parameters: Sector ID , Country Code , Color Code , Subnet Mask , UATI024 , Control Channel Data Rate , Preferred Control Channel Cycle , Pilot Drop , Small Slot Cycle Allowed , Slotted Mode Attribute Values , Prior Session Restore State , Partial HSGW Context Available State Channel Gain/Traffic Info: Traffic Parameters: DRC Length Channel Gain Parameters: ACK Channel Gain , DRC Channel Gain , Data Offset 9k6\|19k2\|38k4\|76k8\|153k6 , Data Offset Nom , Auxiliary Pilot Channel Gain ( only for subtype 2 and subtype 3 physical layer ), DSC Channel Gain ( only for subtype 2 and subtype 3 physical layer ) Power Parameters Info ( only for subtype 2 and subtype 3 physical layer ) including: T2P Transition Settings , Termination Target Settings , TxT2P Gain Settings , Power Parameters Screen Enhanced Traffic Parameters ( only for subtype 2 and subtype 3 physical layer ) including: Auxiliary Pilot Channel Min Payload , DSC Length , Short Packet Enabled Threshold ( only for subtype 2 physical layer ), DRC Length RRI Gain Parameters ( only for subtype 2 and subtype 3 physical layer ) Access Parameters ( for subtype 0 physical layer ) or Enhanced Parameters ( for subtype 2 and subtype 3 physical layer ): Open Loop Adjust Probe Initial Adjust Probe Power Step Probe Num Step Probe Sequence Max Preamble Length (Frames) Preamble Length Slots (applicable to the lab application and to a test application with the required feature license) CDMA System Time / Sync Info: CDMA System Time Parameters , Multi-unit Synchronization (applicable to the lab application and to a test application with the required feature license ) Inter-RAT Config Info (applicable to the lab application only) Inter-RAT Config Parms E-UTRAN Neighbor Parameters E-UTRAN Neighbor EARFCN Parms	Application Config: Session Application Type ( Lab Application Only ) Test Application Protocol ( only for subtype 0 physical layer ) Enhanced Test Application Protocol ( only for subtype 2 physical layer ) Multi-carrier Test Application Protocol ( only for subtype 3 physical layer ) Limited TAP ( only for subtype 0 physical layer ) AT Directed Packets DRC Value Fixed Mode Attribute ACK Channel Bit Fixed Mode Attribute ACK Channel Modulation Type ( only for subtype 2 and subtype 3 physical layer ) Reverse Data Transmission Mode ( only for subtype 2 and subtype 3 physical layer ) Enhanced Access Rate ( only for subtype 2 and subtype 3 physical layer )
Generator Info: Code Channel Parameters ( only for subtype 2 and subtype 3 physical layer ) including: H-ARQ Modulation , ARQ Mode CC , H-ARQ/L-ARQ Channel Level , P-ARQ Channel Level , RPC Channel Level AWGN Power PN Offset External Trigger Type Channel Data Info: ARQ Parameters: ACK R-Data After ( only for subtype 2 and subtype 3 physical layer ) Reverse Activity Parameters Termination Parameters: Max Forward Packet Duration , Forward Early Termination State	FTAP Rate ( only for subtype 0 physical layer ) F-Traffic Format ( only for subtype 2 and subtype 3 physical layer ) F-Traffic Config ( only for subtype 2 and subtype 3 physical layer )
Multicarrier Info ( only for subtype 3 physical layer ), see Multi-carrier Multi-unit (MCMU) : Multicarrier Setup Parms MCMU Automatic Setup Steps Aux Carriers Info External Device Connection
E-UTRAN / eHRPD Interworking (Lab Application Only )
Data Channel (Lab Application Only )	RTAP Rate ( only for subtype 0 physical layer ) R-Data Pkt Size ( only for subtype 2 and subtype 3 physical layer )
Ping (Lab Application Only )	Reverse Closed Loop Power Control
Protocol Logging (applicable to the lab application and to a test application with the required feature license )	Power Control Step
Digital Bus Information ( applicable to the lab application and to a test application with the required feature license with rear panel digital bus only )	Call Drop Timer
Multi-Flow Packet Application Info: ( only for Lab Application and subtype 2 or subtype 3 physical layer ) IP Config Info RLP Info Forward Mappings View Reverse Mappings View Graphical Mappings View	Call Limit Mode
Enh M-Flow Pkt Application Info ( only for Lab Application and subtype 2 or subtype 3 physical layer ) IP Config Info Link Info Forward Mappings View Reverse Mappings View Graphical Mappings View
Traffic Channel MAC Info: ( only for Lab Application and subtype 2 or subtype 3 physical layer ) Traffic Channel MAC Pre Config: Non_Flow Parms Pre Configure , MAC Flow NN Pre Configure FTC MAC Parameters RTC MAC Non-Flow Parms: RTC MAC Flows , RTC MAC Simple Parameters , TxT2P Maximum Parameters , Permitted Payload FlowNN Simple Parameters Info Flow NN Complex Parameters Info	Protocol Rel
	Protocol Subtype Config: Release A Physical Layer Subtype ( only for protocol release A ) Release B Physical Layer Subtype ( only for protocol release B ) Access Channel MAC Subtype Idle State Subtype
	Session Close
	Receiver Control
	Tx Timing Advance